• Resources Recycling
• /
• v.29 no.6
• /
• pp.88-97
• /
• 2020

In this study, the selected waste plastic waste logistics used for cement sintering were classified into two types through the process of sorting and crushing, analyzing the characteristics of each, and analyzing the correlation of the strength after cement manufacturing. The experimental variables were classified into soft and hard waste plastic waste, and the correlations between calorific value, chlorine, and moisture were analyzed. In addition, some of each waste was selected and melted, and the basic characteristics were evaluated by analyzing the structure and calorific value. The results of the experiment showed that it was evaluated that it is suitable to obtain a heat source by separating soft waste plastic wastes and sintering them with materials having similar properties. As a result of examining the wastes by strength after cement manufacturing, it was analyzed that the use of hard plastics greatly contributes to the compressive strength on the 1st and 28th, and the use of soft plastics contributes to the compressive strength on the 28th. However, these characteristics are evaluated by collecting only a part of the waste, and since the deviation of the waste occurs, continuous management is required, and a follow-up study on the environmental problems caused by the use of waste is required.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.6
• /
• pp.561-568
• /
• 2020

Wave measurements using X-band radar have many advantages compared to other wave gauges including wave-rider buoy, P-u-v gauge and Acoustic Doppler Current Profiler (ADCP), etc.. For example, radar system has no risk of loss/damage in bad weather conditions, low maintenance cost, and provides spatial distribution of waves from deep to shallow water. This paper presents new methods for estimating significant wave heights of X-band marine radar images using Artificial Neural Network (ANN). We compared the time series of estimated significant wave heights (Hs) using various estimation methods, such as signal-to-noise ratio (${\sqrt{SNR}}$), both and ${\sqrt{SNR}}$ the peak period (TP), and ANN with 3 parameters (${\sqrt{SNR}}$, TP, and Rval > k). The estimated significant wave heights of the X-band images were compared with wave measurement using ADCP(AWC: Acoustic Wave and Current Profiler) at Hujeong Beach, Uljin, Korea. Estimation of Hs using ANN with 3 parameters (${\sqrt{SNR}}$, TP, and Rval > k) yields best result.

• Journal of Technology Innovation
• /
• v.29 no.1
• /
• pp.1-38
• /
• 2021

In this paper, an exploratory analysis study was conducted on establishing a strategy to utilize living labs to enhance the innovation of the energy sector. Through the previous research literature, it was possible to confirm the concept, essential components, innovation characteristics of living labs, and types of innovation issues in the energy sector as the theoretical background. Based on this, the case studies of energy living lab (8 overseas, 1 domestic) were analyzed focusing on the possibility of utilizing living lab as an approach to innovation issues in the energy sector, establishing a customized strategy for essential components of living lab and enhancing innovation. It was confirmed that the establishment of a customized strategy for the essential components of the living lab could be a driving force in enhancing innovation, and the Living Lab is effectively used as an approach method for innovation issues(demand management, supply technology, enhance R&D acceptance and promote commercialization, technology policies) in the energy sector. As a result of the case studies, the driving force of each living lab was derived from the viewpoint of contributing to innovation, and strategies for using the living labs for each energy innovation problem were established. This study is an exploratory and descriptive analytical study of the utilization strategy and value of the living lab model as an approach to innovation issues in the energy field, which can provide a living lab strategy framework that has not been tried in the past and enables living lab activation and network formation. It can also be considered to have academic, practical, and policy implications in that it can also contribute.

• Korean journal of applied entomology
• /
• v.61 no.1
• /
• pp.197-210
• /
• 2022

Entomopathogenic fungi can be used to control a variety of sucking and chewing insects, with little effect on beneficial insects and natural enemies. Approximately 170 entomopathogenic fungal insecticides have been registered and used worldwide, with the recent focus being on the mode of action and mechanism of insect-fungal interactions. During the initial period of research and development, the industrialization of entomopathogenic fungi focused on the selection of strains with high virulence. However, improvement in productivity, including securing resistance to environmental stressors, is a major issue that needs to be solved. Although conidia are the primary application propagules, efforts are being made to overcome the limitations of blastospores to improve the economic feasibility of the production procedure. Fungal transformation is also being conducted to enhance insecticidal activity, and molecular biology is being used to investigate functions of various genes. In the fungi-based pest management market, global companies are setting up cooperative platforms with specialized biological companies in the form of M&As or partnerships with the aim of implementing a tank-mix strategy by combining chemical pesticides and entomopathogenic fungi. In this regard, understanding insect ecology in the field helps in providing more effective fungal applications in pest management, which can be used complementary to chemicals. In the future, when fungal applications are combined with digital farming technology, above-ground applications to control leaf-dwelling pests will be more effective. Therefore, for practical industrialization, it is necessary to secure clear research data on intellectual property rights.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.8 no.1
• /
• pp.30-42
• /
• 2006

This experiment was conducted to investigate current situation and plant grouping by light and watering of mingled several cacti and succulents in a pot. The main 11 cacti are consist of Myrtillocactus geometrizans (Mart.) Cons., Gymnocalycium mihanovichii var. friedrichii Werd., Marginatocereus marginatus(DC.) Backbg., Eriocactus leninghausii (Hge. Jr.) Backbg, Notocactus scopa (Spreng.) Berg., Lobivia nealeana Backbg., Mammillaria elongata var. intertexta (DC.) SD., Pseudoespostoa (Vp1.) Backbg., Mammillaria albilanata Backbg., Mammillaria klissingiana Bod. and Espostoa lanata (HBK.) Br. & R. The main 10 succulents are Kalanchoe thyrsifolia Harv., Portulacaria afra var. foliis-variegatis Jacobs., Crassula perforata Thunbg., Echeveria pulvinata Rose, Aeonium arboreum cv. atropurpureum., Echeveria lauii Moran & J. Meyran, Pachypodium lamerei Drake, Sedum rubrotinctum cv. Aurora Boom., Aloe mitriformis Mill., and Euphorbia coerulescens Haw. The cacti were native to Mexico, Brazil, Peru, Paraguay, Ecuador, etc. The sucullents were native to Mexico, Africa, Gran Canaria, Madagascar, etc. Most of all the cacti and sucullents in the experiment are growing well under full sun or light shade, however Portulacaria afra var. foliis-variegatis Jacobs, and Sedum rubrotinctum cv. Aurora Boom. did not influenced by light. And all the plants require a little or moderate watering. Thus, planting by similar required water and light, when growing in a pot of several cacti and succulents, might be decreased the rate of death causing by their different plant physiology.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.5
• /
• pp.53-64
• /
• 2009

Many slope failures are induced by rainfall infiltration. A lot of recent researches are therefore focused on rainfall-induced slope instability and the rainfall infiltration is recognized as the important triggering factor. The rainfall infiltrates into the soil slope and makes the matric suction lost in the slope and even the positive pore water pressure develops near the surface of the slope. They decrease the resisting shear strength. In Korea, a few public institutions suggested conservative slope design guidelines that assume a fully saturated soil condition. However, this assumption is irrelevant and sometimes soil properties are misused in the slope design method to fulfill the requirement. In this study, a more relevant slope stability evaluation method is suggested to take into account the real rainfall infiltration phenomenon. Unsaturated soil properties such as shear strength, soil-water characteristic curve and permeability for Korean weathered soils were obtained by laboratory tests and also estimated by artificial neural network models. For real-time assessment of slope instability, failure warning criteria of slope based on deterministic and probabilistic analyses were introduced to complement uncertainties of field measurement data. The slope stability evaluation technique can be combined with field measurement data of important factors, such as matric suction and water content, to develop an early warning system for probably unstable slopes due to the rainfall.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.2
• /
• pp.127-138
• /
• 2023

A variety of decarbonized energy sources are being developed globally to realize carbon neutrality (Net Zero) by 2050 as a measure to address the global climate crisis. As the Korean government has also established a Renewable Energy 3020 policy and promoted energy development plans using solar or wind power, large-scale offshore development projects not present before in coastal waters, such as offshore wind farms, are being promoted. From ships' point of view, offshore facilities present obstacles to safe navigation, and with the installation of marine facilities, ship collisions or contact accidents between ships and marine facilities may occur in the narrowed water areas. In addition, there are concerns about environmental pollution and human casualties caused by marine accidents. Accordingly, we review overseas and domestic offshore wind farm development plans, analyze whether institutional devices are in place to ensure the safe passage of ships in wind farm areas, and study the safe operation of large-scale offshore wind farms and safe passage of ships along the Korean coast by comparing overseas legislative cases with domestic laws and presenting a proposal to illuminate the legal blind sectors.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2023.05a
• /
• pp.108-109
• /
• 2023

The purpose of this study is to set a policy that can be specifically promoted according to the recently announced domestic equipment industry fostering strategy, and to suggest a plan that can be implemented. As a plan to foster the equipment industry, a new technology certification system and a new technology test and verification area operation and vitalization plan were set as alternatives. And a survey was conducted on companies conducting R&D to derive specific demand and introduction plans. As a result of the survey, it was found that there was a high demand for the use of new technology certification systems and testing and verification area. Also demonstration in connection with port equipment, testing and evaluation in connection with accredited verification agency, and preparation of dedicated agencies were derived to foster the equipment industry. Based on this, this study suggests a new technology certification system specialized for port equipment was established and a plan to institutionalize. In addition, in connection with the survey results and certification system, the basic functions and roles of the new technology testing and verification area was established. For future activation, incentives with effective certificates such as exemption of certification costs and issuance of performance confirmation certificates are needed, and efficient operation and management through dedicated organization and certification center were suggested.

• Smart Media Journal
• /
• v.12 no.10
• /
• pp.63-70
• /
• 2023

Recently, energy consumption for heating costs, which is 35% of smart farm energy costs, has increased, requiring energy consumption efficiency, and the importance of new and renewable energy is increasing due to concerns about the realization of electricity bills. Renewable energy belongs to hydropower, wind, and solar power, of which solar energy is a power generation technology that converts it into electrical energy, and this technology has less impact on the environment and is simple to maintain. In this study, based on the greenhouse heat storage tank and heat pump data, the factors that affect the heat storage tank are selected and a heat storage tank supply temperature prediction model is developed. It is predicted using Long Short-Term Memory (LSTM), which is effective for time series data analysis and prediction, and XGBoost model, which is superior to other ensemble learning techniques. By predicting the temperature of the heat pump heat storage tank, energy consumption may be optimized and system operation may be optimized. In addition, we intend to link it to the smart farm energy integrated operation system, such as reducing heating and cooling costs and improving the energy independence of farmers due to the use of solar power. By managing the supply of waste heat energy through the platform and deriving the maximum heating load and energy values required for crop growth by season and time, an optimal energy management plan is derived based on this.

• Journal of the Institute of Convergence Signal Processing
• /
• v.24 no.1
• /
• pp.27-33
• /
• 2023

Recently, water shortages have occurred due to climate change, and the need for water management of agricultural water has increased due to the occurrence of algal blooms in reservoirs. Existing algae prevention is operated by putting many people on site and misses the optimal spraying time due to movement through boats. In order to solve this problem, it is necessary to block contamination in advance and move within time to uniformly spray complex microorganisms uniformly. Control drones are used for pesticide spraying and can be applied to algae prevention work by utilizing control drones. In this paper, basic research for the establishment of a marine control system was conducted for application to the reservoir environment, and as one of the results, the characteristics of a drone nozzle, a core technology that can be used for control drones, were calculated. In particular, it was found that the existing agricultural control drones had a disadvantage that the concentration was non-uniform within the suggested spraying interval, and to compensate for this, nozzle positioning and nozzle spraying uniformity were calculated. Based on the experimental results, we develop a core algorithm for establishing an algal bloom monitoring system in the reservoir environment and propose a precision control technology that can be used for marine control work in the future.