• 한국멀티미디어학회논문지
• /
• 제15권10호
• /
• pp.1212-1220
• /
• 2012

In this paper, a collision-free resource reservation scheme for WUSB (Wireless Universal Serial Bus) networks with WiMedia D-MAC (Distributed Medium Access Control). Since distributed characteristic of the WiMedia D-MAC supporting DRP (Distributed Reservation Protocol) scheme may cause lots of conflicts, overall performances of the WUSB with WiMedia D-MAC can be deteriorated. In addition, when we consider multi-hop environment, "mobile" hidden node problem due to mobility of WUSB devices can be happened, and it is a critical problem to mobile WUSB devices transceiving real-time QoS (Quality of Service) traffic. To tackle the problem, we propose a new DRP reservation mechanism to prevent DRP conflicts for multi-hop mobility support in WUSB networks with WiMedia D-MAC and show its improved performance via simulation results.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.285-292
• /
• 2000

Though there has been increasing use of large diameter drilled shaft as a foundation structure of bridges, current practice for quality control is to confirm the minimum required load carrying capacity during construction stage. For economic and appropriate design of drilled shaft, it is necessary to evaluate the load transfer mechanism by pile load tests during initial stage of construction and to use the test results as a feedback to a revision of initial design. In this paper, results of load tests peformed at several domestic sites are presented to investigate the load transfer characteristics of large diameter drilled shaft. It was found that most of the load on piles is sustained by shaft friction and that only small portion of the load reaches the bottom of the drilled shaft. Some test results of drilled shaft by Pile Driving Analyzer performed at same sites are also presented to compare the load transfer characteristics interpreted from static pile load tests.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2002년도 ICCAS
• /
• pp.56.3-56
• /
• 2002

For the weld quality improvement and the convenient operation of machines, laser vision system can be used to track weld seams on pressure vessels. There are many bad conditions to the weld grooves such as cutting error, gap variation of weld joint, and offset error of center line caused by misalignment. We developed a laser vision seam tracking system which consists of a laser vision sensor, a two axis positioning mechanism and a user interface program running on the Windows system. It was found that our system worked well for U, V and X shaped grooves. We used an industrial PC as the system controller to secure immunity to electrical noise and dust. We introduce here a simple and...

• 한국정밀공학회지
• /
• 제31권2호
• /
• pp.125-131
• /
• 2014

Winding is an integral operation in almost every roll-to-roll continuous process and center-winding is suitable and general scheme in the winding system. However, the internal stresses within center-wound rolls can cause damage such as buckling, spoking, cinching, etc. It is therefore necessary to analyze the relationship between taper tension in winding section and internal stress distribution within center-wound roll to prevent the winding failure. In this study, an optimal taper tension control method with parabolic taper tension profile for producing high quality wound roll was developed. The new logic was designed from analyzing the winding mechanism by using the stress model in center-wound rolls. The performance of the proposed taper tension profile was verified experimentally.

• 한국기계가공학회지
• /
• 제8권4호
• /
• pp.7-13
• /
• 2009

Five-axis laser cutting has great advantages when it is applied to 3-dimensional machining requiring high cutting quality. For developing 5-axis CNC laser cutting systems, however, many problems such as rotating a laser head or a working table, 5-axis servo-control mechanism, tool path generation and post processing, and collision avoidance between a laser head and a work-piece should be solved. In this paper, we deal with developing a dedicated CAM system based on UG-NX3 for 5-axis laser cutting machine. Two essential modules such as post-processor and cutting motion simulation was developed. The developed system was applied to cutting curve defined on 3-D workpiece in order to show the validity of the proposed methods.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1994년도 추계학술대회 논문집
• /
• pp.206-209
• /
• 1994

This paper has been researched bondability of electronic devices, such as lead frame and thick film of Ag/Pd on an alumina substrate by different heat sources. To obtain the bonds with high quality, it is very important to control both the thermal distribution of the bonds and it stability, because electronics components is consist of different materials. Therefore, this paper clarifies not only heat mechanism of micro parallel gap resistance bonding method and pulse heat tip bonding method but also investigates selection of heat sources with micro-electronic materials for bonding. Finally, it is realzed fluxless bonding process with filler metal such as plating layers.

• 한국표면공학회지
• /
• 제29권6호
• /
• pp.691-694
• /
• 1996

Two models of scratch testers developed recently are applied to the adhesion measurement of thin coatings. In both models the critical load is determined from the frictional irregularity when coated surface is broken in the scratching process. One model is effective for coatings thicker than 1m and the other for thin coatings down to $0.1\mu\textrm{m}$. The mechanism and the measurement principle of these testers are described. High sensitivity and good reproducibility of the measurement are attained primarily by the employment of new detection devices. These testers are even more useful for the quality control and the inspection of commercial products of coatings because only a small area of specimen is required for the test.

• 한국정밀공학회지
• /
• 제23권2호
• /
• pp.65-72
• /
• 2006

Downcoiler is one of the major facilities in hot strip mill operation. The key to good coiling is having good equipment, modem control systems, excellent maintenance and an understanding of coiling process. Therefore, this study aims to develop a program that is useful for calculating machine design parameters and simulating coiling process. In this study, the pinching and coiling mechanism of the downcoiler was thoroughly studied and some of operational factors and their effects on the coiling process were investigated. The software was developed to estimate engineering parameters for coiler component design and to determine optimal setting values for successful coiling operation. In order to check the accuracy and usefulness of the developed software, the simulation of the downcoiler in $\#2$ Hot Strip Mill in Pohang Works was performed. The simulation results suggested that the set-up value for unit tension could be lowered. Test coiling operation by using the lowered set-up value for unit tension resulted in much more successful coiling in the aspect of strip quality and power consumption.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.65-66
• /
• 2006

Dancer systems are most widely used mechanism for attenuation of tension disturbances. Lately, demands fur high speed converting machines over 500mpm(m/min) are raising but domestic converting industries can not come up with the machines because capacities for a designing of the converting machine are restricted lower than 300mpm. Moreover roll-to-roll is attracted flexible display manufacturer's attention as a effective method for productivity. A constant tension level in the span before the first printing cylinder is the key of high speed quality printing. This paper presents a modeling and simulations of dancer systems on converting machines.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 기초기술학술발표회
• /
• pp.57-76
• /
• 2002

As piling works in urban area increasing, SIP which is low noise & vibration piling method is taking place of driven pile which has good bearing charateristics and economics. Since SIP has been used for more than 15 years and it's application is increasing year by year, however, accurate analysis of bearing mechanism of SIP is not enough. So the design of SIP is much more conservative than driven pile. This paper is aimed to analyse the bearing charateristics of 103 SIPs constructed in Korea to give rational design criteria. Research result shows that bearing capacity of SIP is 40% lower than that of driven pile and conservative Meyerhof(equation omitted) method produced closer result to load test results than other design method. And this result show that to use optimised design criteria for the economic SIP design, quality control criteria must be settled down to produce high in-situ bearing capacity.