• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.11
• /
• pp.2149-2154
• /
• 2009

Electric power quality in power transmission/distribution systems has considerably been deteriorated with the increase in the capacity of distributed generators (DGs). It is because inverters, connecting DGs to conventional power grids, tend to generate harmonic current and voltage. For harmonic mitigation, a large amount of research has been done on passive and active filters, which have been operating successfully in many countries. This paper, therefore, presents how to adopt the filters to an inverter-based DG, with considering a system consisting of both inverter-based DG and harmonic filters. In particular, this paper describes the simulation results using the PSCAD/EMTDC: firstly, the relationship between total harmonic distortion(THD) of current and output power of DG: secondly, the harmonic mitigation ability of passive and active filters. The system, furthermore, is obliged to satisfy the regulations made by Korean Electric Power Corporation(KEPCO). In the regulations, power factor should be maintained between 0.9 and 1 in a grid-connected mode. Thus, this paper suggests two methods for the system to control its power factor. First, the inverter of DG should control power factor rather than an active filter because it brings dramatic decrease in the capacity of the active filter. Second, DG should absorb reactive power only in the range of low output power in order to prevent useless capacity increase of the inverter. This method is expected to result in the variable power factor of the system according to its output power.

• Journal of Korean Society on Water Environment
• /
• v.24 no.2
• /
• pp.239-246
• /
• 2008

In this study, an optimized deterministic water-quality model was constructed to estimate water quality of a river and lake in the upstream basin of a dam. A stochastic water-quality analysis using reliability analysis technique was applied to the model. The model was tested in the 13.9 km reach from Maeil stage station of Kyechun to Hoengsung Dam of Sum River. After finding hydraulic characteristics from nonuniform flow analysis, Broyden-Fletcher-Goldfarb-Shanno (BFGS) optimization technique for model calibration was applied to determine optimum reaction parameters, and model verification was performed based on these. The stochastic model, using Mean First­Order Second­-Moment (MFOSM) and Monte-Carlo methods, was applied to the same reach as the deterministic study. Variations of discharge and water quality in headwater were considered, as well as variations of hydraulic coefficients and reaction coefficients. The statistical results of output variables from MFOSM were similar to those from the Monte-Carlo method. Risk analysis using MFOSM and Monte-Carlo methods presented the probabilities of some locations in the Hoengsung Lake violating existing water-quality standards in terms of DO and BOD.

• Proceedings of the Korean Association for Survey Research Conference
• /
• 2002.11a
• /
• pp.111-127
• /
• 2002

As the utilization of official statistics has been recently increased, the necessity of objective quality assessment also has been increased. Since mean square error(MSE) and response rate, which have been considered as representative quality indicators in the past, may have the limits of use, it has been demanded to develop new quality indicators which are able to reflect the various requirements of users. In this paper, regarding sample surveys conducted by governmental agencies, the flow of procedures in statistics production is analyzed using input-output of each procedure. As the result, how to identify and develop quality indicators for each procedure is discussed, with some instances of indicators. Finally, the quality index using the results of quality assessment would be calculated based on a weighting method by the size of deviation of statistical measures.

• International Journal of Computer Science & Network Security
• /
• v.21 no.7
• /
• pp.284-296
• /
• 2021

Quality Models are important element of the software industry to develop and implement the best quality product in the market. This type of model provides aid in describing quality measures, which directly enhance the user satisfaction and software quality. In software development, the inheritance technique is an important mechanism used in object-oriented programming that allows the developers to define new classes having all the properties of super class. This technique supports the hierarchy design for classes and makes an "is-a" association among the super and subclasses. This paper describes a standard procedure for validating the inheritance metric in Quality Model for Object-Oriented Design (QMOOD) by using a set of nine properties established by Weyuker. These properties commonly using for investigating the effectiveness of the metric. The integration of two measuring methods (i.e. QMOOD and Weyuker) will provide new way for evaluating the software quality based on the inheritance context. The output of this research shows the extent of satisfaction of the inheritance metric in QMOOD against Weyuker nine properties. Further results proved that Weyker's property number nine could not fulfilled by any inheritance metrics. This research introduces a way for measuring software that developed using object-oriented approach. The theoretical validation of the inheritance metric presented in this paper is a small step taken towards producing quality software and in providing assistance to the software industry.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.43 no.2 s.308
• /
• pp.40-47
• /
• 2006

This paper proposes a multitoning method using threshold modulation of MJBNM(Modified Jointly Blue Noise Mask) for banding artifacts reduction. As banding artifacts in multitoning appear as uniform dot distributions around the intermediate output levels, such multitone output results in discontinuity and visually unpleasing patterns in smooth transition regions. Therefore, to reduce these banding artifacts, the proposed method rearranges the dot distribution by introducing pixels in the neighborhood of output levels that occurs banding artifacts. First of all principal cause of banding artifacts are analyzed using mathematical description. Based on this analytical result, a threshold modulation technique of MJBNM which takes account of chrominance error and correlation between channels is applied. The original threshold range of MJBNM is first scaled linearly sot that the minimum and maximum of the scaled range include two pixel more than adjacent two output levels that cover an input value. In an input value is inside the vicinity of any intermediate output levels produce banding artifacts, the output is set to one of neighboring output levels based on the pointwise comparison result according to threshold modulation parameter that determines the dot density and distribution. In this case, adjacent pixels are introduced at the position where the scaled threshold values are located between two output levels and the minimum and maximum threshold values. Otherwise, a conventional multitoning method is applied. As a result, the proposed method effectively decreased the appearance of banding artifacts around the intermediate output levels. To evaluate the quality of the multitone result, HVS-WRMSE according to gray level for gray ramp image and S-CIELAB color difference for color ramp image are compared with other methods.

• Plant Journal
• /
• v.15 no.3
• /
• pp.23-28
• /
• 2019

In this study, ammonia consumption by gas turbine output was adjusted to find out the amount of ammonia consumption that complies with the enhanced Air Quality Preservation Act and internal regulation emission standards in SCR type DeNOx System for a 580 MW Sejong Combined Cycle Power Plant. For measurements, the gas turbine output was varied to 50, 99, 149, 198 MW and ammonia consumption was adjusted with the combustion gas and ammonia supply conditions fixed at each stage. When the emission limit were change from 10 ppm to 8 ppm, ammonia consumption was increased from 78, 93, 105, 133 kg/h to 89, 113, 132, 176 kg/h. The increase rate of ammonia consumption was 14, 22, 26, 32% per output category compared to the 10 ppm emission limit, which was shown to increase as output increased.

• Current Optics and Photonics
• /
• v.5 no.2
• /
• pp.186-190
• /
• 2021

In this study, a compact, picosecond, mid-infrared 3.8 ㎛ MgO:PPLN optical parametric oscillator (OPO) laser output with high peak power is realized using a master oscillator power amplifier (MOPA) 1 ㎛ solid-state laser seeded by a picosecond fiber laser as the pump source. The pump source was a 50 MHz and 10 ps fiber seed source. After AOM pulse selection and two-stage solid-state amplification, a 1,064 nm laser output with a repetition frequency of 1-2 MHz, pulse width of 9.5 ps, and a maximum average power of 20 W was achieved. Furthermore, a compact short cavity with a unsynchronized pump is adopted through the design of an OPO cavity structure. When the injection pump power was 15 W and the repetition frequency was 1 MHz, the average output power of idler light was 1.19 W, and the corresponding peak power was 119 kW. The optical conversion efficiency was 7.93%. When the repetition frequency was increased to 2 MHz, the average output power of idler light was 1.63 W, the corresponding peak power was 81.5 kW, and the optical conversion efficiency was 10.87%. At the same time, the output wavelength was measured at 3,806 nm, and the beam quality was MX2 = 3.21 and MY2 = 3.34.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.16 no.6
• /
• pp.465-471
• /
• 2023

This paper proposes a comparator structure that improves the noise and output delay of a single-slope ADC(SS-ADC) used in CMOS Image Sensor (CIS). To improve the noise and delay characteristics of the output, a comparator structure using the miller effect is designed by inserting a capacitor between the output node of the first stage and the output node of the second stage of the comparator. The proposed comparator structure improves the noise, delay of the output, and layout area by using a small capacitor. The CDS counter used in the single slop ADC is designed using a T-filp flop and bitwise inversion circuit, which improves power consumption and speed. The single-slope ADC also performs dual CDS, which combines analog correlated double sampling (CDS) and digital CDS. By performing dual CDS, image quality is improved by reducing fixed pattern noise (FPN), reset noise, and ADC error. The single-slope ADC with the proposed comparator structure is designed in a 0.18-㎛ CMOS process.

• Journal of Broadcast Engineering
• /
• v.13 no.6
• /
• pp.941-950
• /
• 2008

The quality of projector output image is influenced by the surrounding conditions such as the shape and color of screen, and environmental light. Therefore, techniques that ensure desirable image quality, regardless of such surrounding conditions, have been in demand and are being steadily developed. Among the techniques, radiometric compensation is a representative one. In general, radiometric compensation is achieved by measuring the color of the screen and environmental light based on an analysis of camera image of projector output image and then adjusting the color of projector input image in a pixel-wise manner. This process is not time-consuming for small sizes of images but the speed of the process drops linearly with respect to image size. In large sizes of images, therefore, reducing the time required for performing the process becomes a critical problem. Therefore, this paper proposes a fast radiometric compensation method. The method uses color filters for eliminating the color mixing between projector and camera because the speed of radiometric compensation depends mainly on measuring color mixing between projector and camera. By using color filters, there is no need to measure the color mixing. Through experiments, the proposed method improved the compensation speed by 44 percent while maintaining the projector output image quality. This method is expected to be a key technique for widespread use of projectors for large-scale and high-quality display.

• Journal of Service Research and Studies
• /
• v.11 no.4
• /
• pp.43-55
• /
• 2021

This study analyzed the efficiency of medical services in OECD member countries by dividing it into operational efficiency and quality efficiency. For this purpose, data from 2017-2019 OECD Health Statistics were used. As the analysis method, super efficiency was measured by applying an output-oriented Variable Returns to Scale (VRS) model. As a result of the analysis, Switzerland, Korea, and Italy were included in the high group of operational efficiency, Canada, Greece, Denmark, etc. in the medium group, and Belgium, Germany, and Spain in the low group. Based on quality efficiency, Norway, Switzerland, and Spain are in the high group, and Greece, Denmark, Mexico, etc. are in the medium group, and the Netherlands, Germany, Belgium, etc. were included in the low group. As a result of comparative analysis of efficiency by OECD member countries as of 2018, it was found that Korea's operational efficiency was the most efficient and quality efficiency was inefficient. Korea (0.998) should improve life expectancy by 0.2 (0.2%) and subjective health perception by 44.2 (138.1%) by benchmarking Greece (0.422), Switzerland (0.207), and Spain (0.371) to improve quality efficiency. Unlike most previous studies that focused on operational efficiency, this study measured quality efficiency together and analyzed the efficiency of the medical service industry in each OECD member country. Through this, this study has implications in that it confirmed the international competitiveness of the domestic medical service industry and suggested ways to improve efficiency.