• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.4
• /
• pp.303-311
• /
• 2014

This paper shows the test result of 2MVA BESS(Battery Energy Storage System) with wind-turbine in micro-grid of the Gapado. To implement of micro-grid with BESS, characteristics of generator and customer load in grid are considered. Also, to operate of 2-parallel PCU(Power Conversion Unit) in BESS, the droop control is adopted with operating mode of grid independent. Performances of BESS with wind-turbine were verified by analysis of power quality such as voltage harmonics, ratio of voltage and frequency regulation, and by measurement of waveform such as output voltage and current.

• Journal of Power Electronics
• /
• v.17 no.3
• /
• pp.686-694
• /
• 2017

Due to the wide use of electronic products, digitally controlled DC-DC converters are attracting more and more attention in recent years. However, digital control strategies may introduce undesirable Limit Cycle Oscillation (LCO) due to quantization effects in the Analog-to-Digital Converter (ADC) and Digital Pulse Width Modulator (DPWM). This results in decreases in the quality of the output voltage and the efficiency of the system. Meanwhile, even if the resolution of the DPWM is finer than that of the ADC, LCO may still exist due to improper parameters of the digital compensator. In order to discover how LCO is generated, the state space averaging model is applied to derive equilibrium equations of a digital PID controlled DC-DC converter in this paper. Furthermore, the influences of the parameters of the digital PID compensator, and the resolutions of the ADC and DPWM on LCO are studied in detail. The amplitude together with the period of LCO as well as the corresponding PID parameters are obtained. Finally, MATLAB/Simulink simulations and FPGA verifications are carried out and no-LCO conditions are obtained.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.15-16
• /
• 2007

The high efficiency and low cost solar cells in order to it applied a dopant pastes diffusion process. The dopant pastes diffusion process which it uses is easily applied in screen-printing solar cells output line. in this paper, it used the Ferro 99-038 phosphorus diffusion pastes source and it analyzed a sheet resistance and a uniformity degree. And it knew the quality of the sheet resistance which it follows in temperature and time condition. The temperature variable it let and it fixed the time in 7 minutes. It will be able to measure the sheet resistance of $40({\Omega}/sq),\;30({\Omega}/sq),\; 20({\Omega}/sq)$. also average uniformity of the sheet resistance was below 5%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.37-38
• /
• 2007

This paper reports the characteristics of piezoelectric microspeakers that are audible in open air with high quality piezoelectric AlN thin film according to the materials properties. When we use a tensile-stressed silicon nitride diaphragm as a supporting layer, the Sound Pressure Level (SPL) is relatively small. However, the SPL of the fabricated microspeakers that have compressive-stressed composite diaphragm show higher output pressure than those of tensile-stressed diaphragm. It produces more than 60dB from 100Hz to 15kHz and the highest SPL is about 100dB at 9.3kHz with 20 Vpeak-to-peak sinusoidal input biases and at 10 mm distances from the fabricated microspeakers to the reference microphone.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.2
• /
• pp.71-77
• /
• 2013

Advanced semiconductor manufacturing technology requires methods to maximize tool efficiency and improve product quality by reducing process variability. Real-time plasma process monitoring and diagnosis have become crucial for fault detection and classification (FDC) and advanced process control (APC). Additional sensors may increase the accuracy of detection of process anomalies, and optical monitoring methods are non-invasive. In this paper, we propose the use of a chromatic data acquisition system for real-time in-situ plasma process monitoring called the Plasma Eyes Chromatic System (PECS). The proposed system was initially tested in a six-inch research tool, and it was then further evaluated for its potential to detect process anomalies in an eight-inch production tool for etching blanket oxide films. Chromatic representation of the PECS output shows a clear correlation with small changes in process parameters, such as RF power, pressure, and gas flow. We also present how the PECS may be adapted as an in-situ plasma arc detector. The proposed system can provide useful indications of a faulty process in a timely and non-invasive manner for successful run-to-run (R2R) control and FDC.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.64 no.2
• /
• pp.79-84
• /
• 2015

Voltage sags are considered the dominant disturbances affecting power quality. Dynamic voltage restorers(DVRs) are mainly used to protect sensitive loads from the electrical network voltage disturbances such as sags or swells and could be used to reduce harmonic distortion of ac voltages. The typical DVR topology essentially contains a PWM inverter with LC Filter, an injection transformer connected between the ac voltage line and the sensitive load, and a DC energy storage device. For injecting series voltage, the PWM inverter is used and the passive filter consist of inductor(L) and capacitor(C) for harmonics elimination of the inverter. However there are voltage pulsation responses by the characteristic of the LC passive filter that eliminate the harmonics of the PWM output waveform of the inverter. Therefore, this paper presented design and feedback performance of LC filter used in the DVRs. The voltage control by LC filter should be connected in the line side since this feedback method allows a relatively faster dynamic response, enabling the elimination of voltage notches or spikes in the beginning and in the end of sags and strong load voltage THD reduction. Illustrative examples are also included.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.11
• /
• pp.1645-1650
• /
• 2015

This paper presents the 3-dimensional electromagnetic field analysis method and correction of sensor distortion that is used by a motor speed sensor. The magnetic sensors are being expanded due to lower price than the other speed sensors such as resolver and encoder. Magnetic sensor generates sine and cosine waves when the motor rotates. However, the sine and cosine signals are distorted due to magnetic noise, which makes the angle error of the sensor, generated near by the Hall element. This paper defines an optimal design variables by using the Taguchi method to minimize output distortion of the magnetic sensor and permanent magnet. To enhance reliability of the magnetic position sensor from sensitivity error, assembly amplitude mismatch and the electrical angle, 3-Dimensional electromagnetic finite element method and correction algorithm errors were performed in due of the magnetic sensor in order to improve the quality of the initial production model.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.477-478
• /
• 2006

Characteristics of InAs/GaAs quantum dot (QD) ridge laser diodes (LDs) are investigated for high-power $1.3\;{\mu}m$ applications. For QD ridge LDs with a $5-{\mu}m$-wide stripe and a 1-mm-long cavity, the emission wavelength of 1284.1 nm, the single-uncoated-facet CW output power as high as 90 mW, the external efficiency of 0.31 W/A and the threshold current density of $800\;mA/cm^2$ are obtained. The linewidth enhancement factor ($\alpha$-factor) is successfully measured to be between 0.4 and 0.6, which are about four times as small values with respect to conventional quantum well structure. It is possible that this result significantly reduce the filamentation of far-field profiles resulting in better beam quality for high power operation.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1684-1686
• /
• 2005

As photovoltaic(PV) power generation systems become more common, it will be necessary to investigate islanding detection method for PV systems. Islanding of PV systems can cause a variety of problems and must be prevented. However, if the real and reactive power of load and PV system are closely matched, islanding detection by passive methods becomes difficult. Also, most active methods lose effectiveness when there are several PV systems feeding the same island. The active frequency drift positive feedback method(AFDPF) enables islanding detection by forcing the frequency of the voltage in the island to drift up or down. In this paper the research for the minimum value of chopping fraction gain applied digital phase-locked-loop(DPLL) to AFDPF considering output power quality and islanding prevention performance are performed by simulation and experiment in IEEE Std 929-2000 islanding test.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.10
• /
• pp.826-831
• /
• 2009

In this paper, a high power RF amplifier module using AlN substrate of high thermal conductivity has been proposed. This RF amplifier module has the advantage of compact size and effective heat dissipation for the packaging of high power chip. To fabricate the thru-hole and scribing line on AlN substrate, the key parameters of $CO_2$ laser were experimented. And then, microstrip lines and spiral planar inductors were fabricated on an AlN substrate using the thin-film process. The fabricated microstrip lines on the AlN substrate has an attenuation value of 0.1 dB/mm up to 10 GHz. The fabricated spiral planar inductor has a high quality factor, a maximum of about 62 at 1 GHz for a 5.65 nH inductor. Packaging of a RF power amplifier was implemented on an AlN substrate with thru-hole. From the measured results, the gain is 24 dB from 13 to 15 GHz and the output power is 33.65 dBm(2.3 W).