• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.903_904
• /
• 2009

본 논문에서는 대표적인 고조파 저감기법인 단일동조 수동고조파필터(single-tuned Passive Harmonic Filter)의 설계 시에 반드시 고려해야 할 최적의 동조계수($\delta$)와 양호도(Q)값의 결정 방법을 제안하였다. 두 값들은 실 사례를 통하여 결정하였고, 결정된 값들은 보드선도를 이용한 주파수 영역 해석을 수행한 후 최종적으로 이 값들을 반영하여 설계된 수동고조파필터의 성능확인을 통하여 본 논문에서 결정한 두 값들의 적합성을 평가하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.3
• /
• pp.454-459
• /
• 2007

In this work, micro-scale, high-performance solenoid-type RF chip inductors utilizing amorphous $Al_2O_3$ core material were investigated. The size of the chip inductors was $0.86{\times}0.46{\times}0.45mm^3$ and copper(Cu) wire with $27{\mu}m$ diameter was used as the coil. High frequency characteristics of the inductance(L), quality factor(Q), impedance(Z), and equivalent circuit parameters of the RE chip inductors were measured and analyzed using an RF impedance/material analyzer(HP4291B with HP16193A test fixture). It was observed that the RF chip inductors with the number of turns of 9 to 12 have the inductance of 21 to 34nH and exhibit the self-resonant frequency(SRF) of 5.7 to 3.7GHz. The SRF of inductors decreases with increasing the inductance and inductors have the quality factor of 38 to 49 in the frequency range of 900MHz to 1,7GHz.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.139-142
• /
• 2003

Microwave dielectric properties of $Ca(Li_{1/4}Nb_{3/4})O_3-CaTiO_3$ ceramic systems were investigated with calcination temperatures and amounts of $CaTiO_3$ in the range of 0.2 to 0.4mol. $Ca(Li_{1/4}Nb_{3/4})O_3$ ceramics having orthorhombic crystal structure could be synthesized at $750^{\circ}C$ and sintered well at $1250^{\circ}C$. They showed the dielectric constant of 26, quality factor($Q{\times}f_o$) of 13,000 and temperature coefficient of resonant frequency(${\tau}_f$) of $-49{\pm}2ppm/^{\circ}C$ With adding the $CaTiO_3$ amount the dielectric constant and ${\tau}_f$ increased due to the solute of $CaTiO_3$ but the quality factor decreased. The 0.7$Ca(Li_{1/4}Nb_{3/4})O_3-0.3CaTiO_3$ ceramic showed the dielectric constant of 44, quality factor($Q{\times}f_o$) of 12,000 and ${\tau}_f$ of $-9{\pm}1ppm/^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.6
• /
• pp.524-530
• /
• 2006

$xCa(Li_{1/4}Nb_{3/4})O_{3}-(1-x)CaTiO_{3}$ ceramics were sintered under the presence of zinc-borosilicate(ZBS) glass and resultant microwave dielectric properties were investigated with a view to applying the composition to low-temperature co-fired ceramic(LTCC) technology. The addition of $5{\sim}15wt%$ ZBS glass ensured successful sintering below $900\;^{\circ}C$. In general, increased addition of ZBS glass increased sinterability but it decreased the quality factor($Q{\times}f_{0}$) significantly due to the formation of an excessive liquid and second phases. As for the addition of $CaTiO_3$, the dielectric constant(${\epsilon}_r$) and temperature coefficient of resonant frequency(${\tau}_f$) increased, while the quality factor($Q{\times}f_{0}$) did not show an apparent change. The sintered $0.9Ca(Li_{1/4}Nb_{3/4})O_{3}-0.1CaTiO_{3}$ specimen at $900\;^{\circ}C$ with 10 wt% ZBS glass demonstrated 39.6 in dielectric constant(${\epsilon}_r$), 4,400 in quality factor$(Q{\times}f_{0}),\;and\;-11ppm/^{\circ}C$ in temperature coefficient of resonant frequency(${\tau}_f$).

• Journal of Korean Society on Water Environment
• /
• v.25 no.6
• /
• pp.902-909
• /
• 2009

With various reservoirs, dams and reduction of water velocity in downstream, rivers in Korea often have characteristics of accumulation of pollutants. Therefore, the main focus of water quality modeling in Korea needs to be shifted from DO to algae and organic matter. Moreover the structures of water quality models should be modified to have capability of simulating BOD which is a key factor of total water pollution load management in Korea as laboratory experiment BOD (Bottle $BOD_5$). In the SWAT model which is one of the widely used water quality models in Korea, the channel water quality module is using main algorithm of the QUAL2E model which has limitations in simulating algae, organic matter and Bottle BOD5 etc. To overcome this hindrance, in this study, the improved channel water quality module of the SWAT model (Q-SWAT) was proposed by linking the algorithms of the QUAL-NIER model which was developed based on the QUAL2E model to the SWAT model. The algorithms estimating the increase of internal organic matter by fractionization algal metabolism process and calculating Bottle $BOD_5$ were added and the results of proposed model were compared to those of the original SWAT model. The results of comparison test are showing that more accurate BOD values can be obtained with the Q-SWAT model and it is anticipated that the Q-SWAT model can be used as an effective tool of decision support through the water quality simulation and long term pollution source analysis.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.636-639
• /
• 2000

Effects of sintering temperature and time on relative permittivity $\varepsilon$$\_$r/, unloaded quality factor Q$.$f and temperature coefficient of resonant frequency $\tau$$\_$f/ of dielectric resonator materials produced from commercial ZST powder were investigated in some detail. Q$.$f values, as determined from cavity perturbation method at 1.6 GHz, gradually increased with sintering temperature reaching the maximum at 1420$^{\circ}C$. However, bulk density and relative permittivity values, which increased with temperature, started to decrease above 1380$^{\circ}C$. In addition, Q$.$f values slightly increased with sintering time at the sintering temperature of 1300$^{\circ}C$∼1380$^{\circ}C$, while bulk density and relative permittivity values were approximately constant. It was also found that $\tau$$\_$f/ values were not affected by sintering temperature and time within the experimental conditions used.

• Current Optics and Photonics
• /
• v.7 no.3
• /
• pp.248-253
• /
• 2023

An efficient global optimization approach for a periodic plasmonic nanoslit array based on extraordinary optical transmission within an acceptable time range is proposed using 𝚀 factor analysis method. The particle swarm optimization is employed as a global optimization tool. The figure of merit is defined as a product of transmission peak value and 𝚀 factor. The design variables are the slit width, height, and period of the slit array, respectively. The optical properties such as transmission spectrum and bandwidth are calculated rigorously using the finite element method.

• Geophysics and Geophysical Exploration
• /
• v.14 no.3
• /
• pp.242-248
• /
• 2011

By applying analytic method to the uniform model, the intrinsic and scattering quality factor ($Q_i^{-1}$ and $Q_s^{-1}$) was separated for the southeastern part of Korean Peninsula. The Multiple Lapse Time Window Analysis method was used to fit theoretical values with observations obtained 759 earthquake data. While previous study for the Korean Peninsula showed very low $Q_i^{-1}$ and $Q_s^{-1}$ reflecting inactive seismicity, southeastern Korea exhibited relatively high $Q_i^{-1}$ and $Q_s^{-1}$ values interpreted as higher seismicity than the other region in the peninsula.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.1
• /
• pp.137-146
• /
• 2009

We present a micromechanical digital-to-analog (DA) variable capacitor using a parallel digital actuator array, capable of accomplishing high-Q tuning. The present DA variable capacitor uses a parallel interconnection of digital actuators, thus achieving a low resistive structure. Based on the criteria for capacitance range ($0.348{\sim}1.932$ pF) and the actuation voltage (25 V), the present parallel DA variable capacitor is estimated to have a quality factor 2.0 times higher than the previous serial-parallel DA variable capacitor. In the experimental study, the parallel DA variable capacitor changes the total capacitance from 2.268 to 3.973 pF (0.5 GHz), 2.384 to 4.197 pF (1.0 GHz), and 2.773 to 4.826 pF (2.5 GHz), thus achieving tuning ratios of 75.2%, 76.1%, and 74.0%, respectively. The capacitance precisions are measured to be $6.16{\pm}4.24$ fF (0.5 GHz), $7.42{\pm}5.48$ fF (1.0 GHz), and $9.56{\pm}5.63$ fF (2.5 GHz). The parallel DA variable capacitor shows the total resistance of $2.97{\pm}0.29\;{\Omega}$ (0.5 GHz), $3.01{\pm}0.42\;{\Omega}$ (1.0 GHz), and $4.32{\pm}0.66\;{\Omega}$ (2.5 GHz), resulting in high quality factors which are measured to be $33.7{\pm}7.8$ (0.5 GHz), $18.5{\pm}4.9$ (1.0 GHz), and $4.3{\pm}1.4$ (2.5 GHz) for large capacitance values ($2.268{\sim}4.826$ pF). We experimentally verify the high-Q tuning capability of the present parallel DA variable capacitor, while achieving high-precision capacitance adjustments.

• Economic and Environmental Geology
• /
• v.32 no.4
• /
• pp.379-384
• /
• 1999

In order to know the characteristics of attenuation of coda wave in the Kyungsang Sedimetary Basin, quality faclity factor for coda wave (coda Q) is estimated from the earthquake data recorded in the KIGAM local seismic network. Thesingle scattering model for coda wave generation is adopted is adopted in estimating coda Q. In the present study, coda Q(Qc)is estimated in the range of $\alpha$=1.5~3.0, where $\alpha$ denotes the normalized time to S-wave travel time and expressed in terms of frequency (f). The deduced function in the range of 1 to 25 Hz is Qc=36.8283$f^{1.15095}$ which represents the strong dependence of coda Q on frequency. It is found that the difference of Qc between U-D, N-S, and E-W components is negligible. This fact suports the back scattering therory that coda wave originates from scattered waves by randomly distributed heterogenities in the crust On the other hand, it is observed that the coda Q increases with increasing epicentral distence. This observation suggests that QC increases with depth.