• Journal of the Korean Applied Science and Technology
• /
• v.32 no.2
• /
• pp.281-289
• /
• 2015

This study investigated the conversion of oil products from polypropylene by using dispersed Co and Mo catalyst on reaction time and concentration change for knowledging liquefation characteristics at low-temperature (425, 450 and $475^{\circ}C$) pyrolysis in a batch reactor. The reaction time was set in 20~80 minutes and the oil products formed during pyrolysis were classfied into gas, gasoline, kero, diesel and heavy oil according to the domestic specification of petroleum products. The pyrolysis conversion rate was showed as Mo catalyst > Co catalyst > Thermal in all reaction time at reaction temperature $450^{\circ}C$. The conversion rate and yields of the pyrolysis products were the most height when Co and Mo Catalyst ratio was 50:50.

• Korean Journal of Materials Research
• /
• v.19 no.11
• /
• pp.581-587
• /
• 2009

Fe powders with elongated and aggregated structure as heat pellet material for thermal battery applications were prepared by spray pyrolysis under various preparation conditions. The precursor powders with spherical shapes and hollow morphologies turned into Fe powders after reduction at a temperature of 615$^{\circ}C$ under 20% $H_2$/Ar gas. The powders had pure Fe crystal structures irrespective of the preparation conditions of the precursor powders in the spray pyrolysis. The morphologies and mean sizes of the Fe powders are affected by the preparation conditions of the precursor powders in the spray pyrolysis. Therefore, the ignition sensitivities and the burn rates of the heat pellets formed from the Fe powders prepared by spray pyrolysis are affected by the preparations of the precursor powders. The Fe powders prepared under the optimum preparation conditions have a BET surface area of 2.9 $m^2g^1$. The heat pellets prepared from the Fe powders with elongated and aggregated structure have a good ignition sensitivity of 1.1W and a high burn rate of 18 $cms^1$.

• Journal of the Korean Society of Tobacco Science
• /
• v.30 no.2
• /
• pp.94-102
• /
• 2008

In this paper, we describe our study on the characterization of tobacco leaves by their pyrolysis patterns. Two kinds of tobacco leaves were pyrolyzed and analyzed by Double-Shot Pyrolysis-Gas Chromatography/Mass Spectroscopy (Py-GC/MS) methods. Three grades of Korean flue-cured tobacco leafsuch as B1O, AB3O, CD3L and burley tobacco leaves such as B1T, AB3T, CD3W were pyrolyzed with six discrete but stepwise heating temperature ranges, those are from 100$^{\circ}C$ to 150$^{\circ}C$, 150$^{\circ}C$ to 200$^{\circ}C$, 200$^{\circ}C$ to 250$^{\circ}C$, 250$^{\circ}C$ to 300$^{\circ}C$, 300$^{\circ}C$ to 350$^{\circ}C$ and finally from 350$^{\circ}C$ to 400$^{\circ}C$. Using the resultant 52 pyrolytic components identified in the programs as components, principal component analysis (PCA) showed statistical classification between flue-cured and burley tobacco lamina. Among six pyrolysis temperature ranges, the best discrimination was achieved at the temperature range from 250$^{\circ}C$ to 300$^{\circ}C$ and from 300$^{\circ}C$ to 350$^{\circ}C$.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.16 no.4
• /
• pp.57-63
• /
• 2008

The characteristics of the bio-oil produced by the pyrolysis process with pig feces was investigated in this paper. The continuous auger-type reactor produced bio-oil was maintained at the temperature range of 400 to $600^{\circ}C$, which was higher than a typical that in a conventional pyrolysis system. The pig feces was used as the feedstock. The bio-oil and its compositions were characterized by water analysis, heating values, elemental analysis, bio-oil compounds, by Gas Chromatography/Mass Spectrometry (GC/MS), and functional group by $^1H$ NMR spectroscopy. It was found that the maximum bio-oil yields of 21% w.t. was achieved at $550^{\circ}C$. This result suggested that this auger reactor might be a potential technology for livestock waste treatment to produce bio-oil because it is able to be improved to reach higher efficiency of bio-oil production in further study. The pyrolysis system reported herein had low heat transfer into the feedstock in the auger reactor so that it needs improve the heat conduction rate of the system in further study.

• Journal of Environmental Science International
• /
• v.11 no.4
• /
• pp.375-382
• /
• 2002

The total hydrocarbon distribution of oil products obtained from the pyrolysis of four kinds of mixtures of polyethylene-polystyrene waste has been studied by multidimensional chromatography(high performance liquid chromatography followed by capillary gas chromatography)/mass spectrometry. Saturated, unsaturated and aromatic hydrocarbons in oil products were selectively pre-separated according to structural groups by HPLC and the weight fraction of each group was estimated by analysis of each component using GC-FID response factors. The hydrocarbon distribution of aliphatic fraction consists of $C_{5}$ to $C_{25}$ saturated and unsaturated hydrocarbons. And that of aromatics fraction consists of benzene, toluene, xylene, styrene, propenyl benzene, naphthalene, and some of derivatives. Pyrolysis temperature did not affect the ratio of total weight fraction of aliphatic over aromatic hydrocarbon distribution in case of PS only and PE-PS mixtures (1:1 and 1:4 wt. ratio) as a feed while affected the ratio of total wt. fraction in case of PE only. The optimal temperature for the maximum oil production was $600^{\circ}C$ for pyrolysis of PS and 1:1 and 1:4 mixtures of PE and PS. The optimal condition for aromatic recovery was $600^{\circ}C$ with 1:1 mixture of PE and PS. In this condition, aromatic was produced up to 90% of total oil product. The maximum yield of toluene, xylene, styrene, and propenyl benzene were 8.6, 8.9, 51.0 and 7.4% of feed for pyrolysis PS at $700^{\circ}C$, respectively. However, only 1.3% naphthalene was recovered at $700^{\circ}C$ with 1:1 PE:PS(by wt.).

• Resources Recycling
• /
• v.17 no.6
• /
• pp.50-56
• /
• 2008

A polypropylene fraction collected from the stream of post-consumer plastics was pyrolyzed. The aim of this study is to observe the dependence of yield of BTEX-aromatics normally used as solvent on the reaction temperature. To reach the goal, three experiments were carried out at different temperature between 650 and $700^{\circ}C$, using a fluidized bed reactor that shows an excellent heat transfer. In the experiments, product gases were used as a fluidizing medium to maximize the amount of BTEX-aromatics at fixed flow rate and feed rate during the pyrolysis. Oil, gas and char were obtained as product fractions. Product gases were analyzed with GCs(TCD, FID) and with a GC-MS system for qualitative analysis. For an accurate analysis of product oil, the product oil was distilled under vacuum, and separated the distillation residues from oil fractions that were actually analyzed with a GC-MS system. As the reaction temperature went higher, the content of BTEX-aromatics increased. The maximal yield of BTEX-aromatics was obtained at $695^{\circ}C$ with a value of about 30%. The main compounds of product gas were $CH_4$, $C_2H_4$, $C_2H_6$, $C_3H_6$, $C_4H_{10}$ and the product gas had an higher heating value about 45MJ/kg. It could be used as a heat source for a pyrolysis plant or for other fuel applications.

• Journal of Energy Engineering
• /
• v.16 no.1 s.49
• /
• pp.32-39
• /
• 2007

Coal pyrolysis processes vary with the origin and rank of coal. It is difficult to generalize the characteristics of coal pyrolysis reaction because the process consists of numerous reactions including pyrolysis, gasification, and combustion. To find out the optimum process condition it is necessary to determine the condition fur each coal from the smatter scale experiment. In this study pressurized ($2kg_{f}/cm^{2}$) fluidized bed, low temperature ($735{\sim}831^{\circ}C$) gasification using Kideco coal was performed. The reaction condition and product gas composition were determined from the variables including steam flow rate, coal feed rate and air flow rate. Optimum reaction condition was determined from the concentrations of $H_{2}$, and CO in the product gas. The ratio of air/coal was 4.45 and that of steam/coal was 0.21 respectively. The concentrations of CO and $H_{2}$ decreased with the increase of $CO_{2}$. It is important to control the feed rates of coal and steam because the reaction temperature rapidly increased when the combustion reaction dominates over the gasification reaction. The concentrations of CO and $H_{2}$ were 18%, 17% respectively from the continuous operating condition.

• Journal of the Korean Wood Science and Technology
• /
• v.14 no.2
• /
• pp.21-28
• /
• 1986

A quartz type gasification reactor was designed and used for pyrolysis and gasification of sawdust, ricestraw and ricehusk. The initial reaction temperature was 350$^{\circ}C$, and up to 550$^{\circ}C$ to complete pyrolysis and gasification reaction. In order to examine the effect of catalyst on reaction temperature, $K_2CO_3$ and $Na_2CO_3$ as catalyst were also used. The product gas mixtures are identified to be CO, $CO_2$, $CH_4$ and $CH_3CHO$ etc. by Gas Chromatography and Mass Spectrometer. The highest gas volume of the gasified sawdust at 550$^{\circ}C$ amounts to 1800ml/g of sawdust, even though the yield and composition of this product gas are depending on the reaction temperature of the reactor and catalyst used.

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.1
• /
• pp.34-39
• /
• 2017

The recent gradual increase in the energy demand is mostly met by fossil fuel, but the research on and development of new alternative energy sources is drawing much attention due to the limited fossil fuel supply and the greenhouse gas problem. This paper assesses the feasibility of producing fuel energy from a dewatered sewage sludge by microwave-induced pyrolysis with sludge char and graphite receptor. Both receptors produced gas, char, and tar in order from product amount. The gas produced for the sludge char receptor contained mainly hydrogen and methane with a small amount of light hydrocarbons. The graphite receptor generated higher gravimetric tar and generated higher light tar. Through the results, the product gas from the microwave processes of wet sewage sludge might be possible as a fuel energy. But the product gas has to be removed the condensable PAH tars.

• Clean Technology
• /
• v.27 no.3
• /
• pp.232-239
• /
• 2021

In order to develop a novel system named "thermal medium and gas circulation type pyrolysis system," this study was conducted to obtain basic data for process simulation before performing the pyrolysis experiment. Polypropylene (PP) was chosen as model material in the basic pyrolysis experiment instead of waste plastic and fluidized sand (hereinafter referred to as "sand"), and it was used as a heat transfer material in the "thermal medium and gas circulation type pyrolysis system." Ni was impregnated as an active catalyst on the sand to promote catalytic pyrolysis. The basic physical properties of PP were analyzed using a thermogravimetric analyzer, and pyrolysis was performed at 600 ℃ in an N₂ atmosphere to produce liquid oil. The distribution of the carbon number of the liquid oil generated through the catalytic pyrolysis reaction was analyzed using GC/MS. We investigated the effects of varying the pyrolysis space velocity and catalyst amount on the yield of liquid oil and the carbon number distribution of the liquid oil. Using Ni/sand, the yield of liquid oil was increased except with the pyrolysis condition of 10 wt% Ni/sand at a space velocity of 30,000 h^-1, and the composition of C₆ ~ C₁₂ hydrocarbons increased. With increases in the space velocity, higher yields of liquid oil were obtained, but the composition of C₆ ~ C₁₂ hydrocarbons was reduced. With 1 wt% Ni/sand, the oil yield obtained was greater than that obtained with 10 wt% Ni/sand. In summary, when 1 wt% Ni/sand was used at a space velocity of 10,000 h^-1, the oil yield was 60.99 wt% and the composition of C₆ ~ C₁₂ hydrocarbons was highest at 42.06 area%.