• Journal of the Korean Institute of Telematics and Electronics
• /
• v.22 no.3
• /
• pp.54-59
• /
• 1985

From the foregoing papers, it has been clarified that the push-pull current-fed DC-DC converter is excellent in stability as compared with the other conventional DC-DC con-verters. The relation between the stability of the converter and the capacitance of smoothing condenser is analyzed, considering the ESR of smoothing condenser and the 1 st order phase lag of the feedback circuit. From the results, it is known that when the capacitance of smoothing condenser is reduced, the stability of the converter is also excellent as compared with the conventional buck type converter, whereas there are limitations for practical use, since the ripple of output voltage increases by increasing of output current.

• Journal of Power Electronics
• /
• v.6 no.2
• /
• pp.95-103
• /
• 2006

In this paper, a novel prototype of auxiliary switched capacitor assisted voltage source soft switching PWM Single-Ended Push Pull (SEPP) series capacitor compensated load resonant inverter with two auxiliary edge resonant lossless inductor snubbers is proposed and discussed for small scale consumer high-frequency induction heating (IH) appliances. The operation principle of this inverter is described by using switching mode equivalent circuits. The newly developed multi resonant high-frequency inverter using trench gate IGBTs can regulate its output AC power via constant frequency edge-resonant associated soft switching commutation by using an asymmetrical PWM control or duty cycle control scheme. The brand-new consumer IH products which use the newly proposed edge-resonant soft switching PWM-SEPP type series load resonant high-frequency inverters are evaluated using power regulation characteristics, actual efficiency vs. duty cycle and input power vs. actual efficiency characteristics. Their operating performance compared with some conventional soft switching high-frequency inverters for IH appliances is discussed on the basis of simulation and experimental results. The practical effectiveness of the newly proposed soft switching PWM SEPP series load resonant inverter is verified from an application point of view as being suitable for consumer high-frequency IH appliances.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.6 no.2
• /
• pp.105-117
• /
• 2015

The purpose of this study is to develop a new seismic resistant method by using precast concrete wall panels for existing low-rise, reinforced concrete beam-column buildings such as school buildings. Three quasi-static hysteresis loading tests were experimentally performed on one unreinforced beam-column specimen and two reinforced specimens with L-type precast wall panels. The results were analyzed to find that the specimen with anchored connection experienced shear failure, while the other specimen with steel plate connection principally manifested flexural failure. The ultimate strength of the specimens was determined to be the weaker of the shear strength of top connection and flexural strength at the critical section of precast panel. In this setup of L-type panel specimens, if a push loading is applied to the reinforced concrete column on one side and push the precast concrete panel, a pull loading from upper shear connection is to be applied to the other side of the top shear connection of precast panel. Since the composite flexural behavior of the two members govern the total behavior during the push loading process, the ultimate horizontal resistance of this specimen was not directly influenced by shear strength at the top connection of precast panel. However, the RC column and PC wall panel member mainly exhibited non-composite behavior during the pull loading process. The ultimate horizontal resistance was directly influenced by the shear strength of top connection because the pull loading from the beam applied directly to the upper shear connection. The analytical result for the internal shear resistance at the connection pursuant to the anchor shear design of ACI 318M-11 Appendix-D except for the equation to predict the concrete breakout failure strength at the concrete side, principally agreed with the experimental result based on the elastic analysis of Midas-Zen by using the largest loading from experiment.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.747-750
• /
• 1999

A 30Watt inverter with 300: 1 dimming capability for high luminance, one cell, surface discharge plasma light source for LCD backlight was designed and tested. It was possible to achieve 300:1 dimming control by using the push-pull type inverter with burst-mode dimming control. The surface discharge plasma light cell with luminance of more than 5, 260 cd/$m^2$ was successfully operated.

• Journal of KIISE:Databases
• /
• v.31 no.4
• /
• pp.422-431
• /
• 2004

In recent years, different models in data delivery have been explored in mobile computing systems. Particularly, there were a lot of research efforts in the periodic push model where the server repetitively disseminates information without explicit request. However, average waiting time per data operation highly depends on the length of a broadcast cycle and different access pattern among clients may deteriorate the response time considerably. In this case, clients are preferably willing to send a data request to the server explicitly through backchannel in order to obtain optimal response time. We call the broadcast model supporting backchannel as hybrid broadcast. In this paper, we devise a new transaction processing algorithm(O-PreH) in hybrid broadcast environments. The data objects which the server maintains are divided into Push_Data for periodic broadcasting and Pull_Data for on-demand processing. Clients tune in broadcast channel or demand the data of interests according to the data type. Periodic invalidation reports from the server support maintaining transactional consistency. If one or more conflicts are found, conflict orders are determined not to violate the consistency(pre-reordering) and then the remaining operations have to be executed pessimistically. Through extensive simulations, we demonstrate the improved throughput of the proposed algorithm.

• KIPS Transactions on Computer and Communication Systems
• /
• v.7 no.5
• /
• pp.119-126
• /
• 2018

Content-centric networking (CCN) is a future Internet technology to reorganize the paradigm of end-to-end communication of the current IP-based Internet architecture into a content-based paradigm. In managing such new networks, the network management is one of the most important functions. The standard for typical network management in existing IP networks is Simple Network Management Protocol (SNMP). Though there have been several works to implement network management functions on CCN, they have their own limitations to apply them to pure CCN operational environments. The basic reason of the limitation is that existing methods operate in an IP-overlay structure, or do not support push-type information exchange. In this paper, we propose a new naming structure that can accommodate both pull and push-type SNMP methods for CCN network management with SNMP. Then, methods to support GET and TRAP methods as well as a SET method of SNMP in the pure CCN environment using the proposed naming structure are proposed. We implement the proposed method using CCNx, and construct a CCN network testbed to validate the effectiveness of the proposed method by monitoring appropriate exchange of SNMP messages over the testbed.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.227-231
• /
• 2003

In This paper, A novel zero-voltage-switching(ZVS) resonant DC-DC converter is proposed. it is composed of two symmetrical active-clamped circuits, The converter can achieve each switchs ZVS. proposed circuit is active clamp capacitor Ratios can be reduce switching voltage stress of each main switch. Simulation results using Pspice ver 9.2 show that the prove the validity of theoretical analysis.

• Journal of Biosystems Engineering
• /
• v.25 no.1
• /
• pp.19-24
• /
• 2000

This study was carried out to develop gripper which to adaptive variable tray and to develop automatic transplanting system for seedling-production system between tray. This system consisted of five set of gripper and end-effector, a planting-width control unit, a tray transfer unit, and gripper moving device which move gripper between nursing tray and growing tray. This system used push-out rod to grasp plant instead of pull-out end -effector. Several types of fingers, which physically grip seedlings, were also developed and tested to ensure reliable transplanting operation of the gripper. The transplanting system detaches seedlings from a tray with push-o0ut rods, which were installed under the tray transfer unit. The performance of the transplanting system was evaluated by successive transplanting experiments. Using the best type of finger , the transplanting system produced 94.6% of transplanting success rate.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.2
• /
• pp.140-149
• /
• 1985

Fully reversed push-pull low cycle fatigue tests under strain control of trapezoid cyclic mode have been conducted in air at temperature of 550.deg. C and with frequency of 0.5 cpm on the domestic stainless steel STS 316 after solution treatment for 1 hour at 1100.deg. C. As an experimental equipment for high temperature fatigue tests, an electric servo-hydraulic fatigue machine(Instron model 1350) was used. This paper presents the effects of creep hold time and plastic strain range on push-pull high temperature low cycle fatigue life and fracture behavior. The fracture surfaces were observed by means of the scanning electron microscope. The results are as follows. (1) The fatigue life decreases with increase of the plastic strain range equal hold time and also decreases as the hold time is getting longer. (2) The frequency modified damage function can predict fatigue life by incorporating a variation of Coffin's frequency modified approach into damage function. (3) The ratios of creep damage and fatigue damage can be calculated by using he linear accumulation damage concept and the ratio of creep damage increases as the hold time is getting longer. (4) At the creep hold time of 5 minutes and the strain range of 2.0%, the fracture mode was intergranular fracture and striations were hardly observed. In this case, the intergranular cracking was originated in void type('.gamma.' type) cracking.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.4
• /
• pp.364-375
• /
• 2014

Parametric array transducers are used for long-range and highly directional communication in an underwater environments. The power amplifiers for parametric array transducers should have sufficient linear output characteristic and high efficiency to avoid communication errors, system heating, and fuel problems. But the conventional power amplifier with fixed source voltage is very low efficient due to large power loss by the big difference between the fixed source voltage and the amplifier output voltage. Thus to solve the problems this paper proposes the high efficiency power amplifier for parametric array transducers. The proposed power amplifier ensures high linearity of output characteristic by utilizing the push-pull class B type amplifier and furthermore gets high efficiency by applying the envelope tracking technique that variable source voltage tracks the envelope of the amplified signal. Also the paper suggests the detailed circuit topology and design guideline of class B push-pull type amplifier and variable output voltage AC/DC converter. Its characteristics are verified by the detailed simulation and experimental results.