• Journal of Welding and Joining
• /
• 제31권3호
• /
• pp.39-43
• /
• 2013

It is difficult to feed welding wire stably, when the distance between welding wire feeder and welding torch is far enough. In order to solve this problem, arranging a extension wire feeder between them could be one of useful methods. However, the welding wire could be twisted up in the extension cable between extension and terminal wire feeders in the case that RPM of extension wire feeding motor is higher than that of terminal motor. In this study, feeding problem of normal push-pull wire feeding system occurred at low welding current range less than 250A. In order to solve the problem, two new wire feeding systems of push-pull type were introduced. Welding wire feeding tests were preformed in the range of 150A to 400A with the developed push-pull feeding system. In addition, weldability test was performed at the welding current of 200A, 300A, and 400A. The welding wire twisting problem that was observed in the normal feeding system did not occur in the new push-pull wire feeding system.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2012년도 전력전자학술대회 논문집
• /
• pp.7-8
• /
• 2012

본 논문에서는 저전압 대전류 입력의 DC/DC컨버터에서 과도한 전류 스트레스를 부담하는 변형된 Push-Pull type 컨버터를 제안한다. 제안된 컨버터는 변압기에 병렬로 권선과 스위치를 구성하며 L-C공진을 통해 소프트스위칭을 실현한다. 이를 시뮬레이션 및 실험을 통해 검증하였다.

• Journal of Information Display
• /
• 제9권2호
• /
• pp.9-13
• /
• 2008

A novel push-pull voltage converter structure, using a switched capacitor type voltage doubler, is proposed. The circuit is constructed with a two-stage push-pull voltage doubler that has a stable operation with small output ripple. The two-stage voltage doubler creates the output voltage 4Vdd. The high clock signal is cross-coupled to the input of the second stage with the opposite phase to reduce two switching transistors and capacitors. Simulation results verify that even with a reduced number of transistor and capacitor, there is no circuit performance loss. Adding one capacitor and two switching transistors the circuit can be changed to eight times of Vdd maker.

• 한국음향학회지
• /
• 제19권4호
• /
• pp.107-114
• /
• 2000

기존의 Push-Pull 트랜스듀서보다 간단한 구조를 가지며 출력을 한층 더 높이기 위해서 실린더 중앙에 구동부를 둔 새로운 구조의 Push-Pull 트랜스듀서를 설계하고자 한다. 유한 요소 상용 패키지인 ANSYS를 이용하여 트랜스듀서 모델을 구성한 후, 각종 구조 변수들, 즉, 길이, 반경, Endcap Edge 형상등의 변화에 대한 음압의 변화경향을 조사하여 최대 음압을 구현하기 위한 최적 길이, 반경, Endcap Edge 형상을 설정하였다. 기존 트랜스듀서 보다 구조적으로 더 간단하면서도 더 큰 음압을 구현할 수 있는 새로운 구조의 고출력 트랜스듀서를 개발하였고, 그 성능을 기존 트랜스듀서의 성능과 비교 평가함으로써 개발된 트랜스듀서의 우수성을 입증하였다.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권1호
• /
• pp.19-26
• /
• 1999

A moving-coil-type linear motor, designed and fabricated, is consisted of the NdFeB permanent magnets with high specific energy as the stator, a coil-wrapped nonmagnetic hollow rectangular structure and an iron core as a pathway for magnetic flux. The interaction between permanent magmet and armature fie1d, so called "push/pull effect", is to shift the airgap flux density variation due to the magnet alone by a certain amount. Thrust therefore is shift downward or upward. The push/pull effect was presented through the FEM analysis and the static tests. We compared the thrust obtained through the FEM analysis with the static tests. Finally, we present the linearity and correction coefficients of the thrust in consideration of the push/pull effects.l effects.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.1324-1326
• /
• 2000

This paper proposes a Current-Fed Push Pull type DC-DC converter using LCCC Resonant circuit and Zero Voltage Switching function to reduce turn on and off loss at the switching instants. This paper have the advantage which is able to operating safely in load short, because of DC reactor is connected with resonance reactor in order to supply a fixed current with low ripple from DC Power supply. The capacitor ($C_1$, $C_2$) connected in switch are common using as resonance capacitor and ZVS capacitor. The analysis of the proposed Current-Fed Push Pull type DC-DC converter is generally described by using normalized parameter, and we have evaluated characteristic values which is needed to design a circuit. We confirm a rightfulness theoretical analysis by comparing a theoretical values and experimental values obtained from experiment using MOSFET as switching devices.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.1184-1186
• /
• 2002

Recently, according to the industrial development relative to multimedia, demand of display system is radically increase, thus development for power supply of back-lighting is advanced lively. Fluorescent lamp operated at high frequency by the electronic ballast provide benefits like unnoticeable flicker effect and higher luminous efficiency. This paper presents analysis of Push-Pull type resonant inverter for CCFL drive for stable characteristic and life improvement of fluorescent lamp operated at high frequency. Also it has proposed design procedure of Current-Fed type resonant inverter. On the basis of equivalent circuit, component characteristic and suitable region of operation frequency from simulation using Matlab and Pspice is predicted. Suitability of applied equivalent model and validity of design process from the experimental results with CCFL inverter.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 창립기념 춘계학술대회 논문집
• /
• pp.502-509
• /
• 1998

The scheme to reduce jerking phenomena in one push-pull type trainset was proposed. To simulate the jerking between coaches, dynamic analysis model was made. This model could analyze longitudinal dynamic behavior between locomotives and coaches caused by spring and damping characteristics of couplers and center pivots; characteristic curves of traction and braking. To validate the analysis results, tests were conducted in the same driving and braking condition. Comparison of longitudinal acceleration between simulation and test results shows a good agreement. To minimize the jerking phenomena, lots of dynamic simulations were conducted with varying driving/braking effort curve. From the results of simulations, an efficient and economic way to reduce jerking phenomena was found to be to reduce slope of tractive effort curve and synchronize braking time between locomotives and coaches. Test results show that this way could reduce the jerking Phenomena. To express jerkins Phenomena quantitatively, maximum peak to peak values of acceleration were used.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 A
• /
• pp.275-277
• /
• 1998

The effect of the coil flux, so called "push/pull effect", is to shift the airgap flux density variation due to the magnet alone by a certain amount. Thrust therefore is shift downward or upward. The push/pull effect was presented through the FEM analysis and static tests. We compared with the thrust obtained through the FEM analysis and static tests.

• 전력전자학회논문지
• /
• 제18권3호
• /
• pp.247-255
• /
• 2013

In this paper, a soft switching DC-DC converter for AC module type photovoltaic (PV) module integrated converter is proposed. A push-pull converter is suitable for a low voltage PV AC module system because the step-up ratio of a high frequency transformer is high and the number of primary side switches is relatively small. However, the conventional push-pull converters do not have high efficiency because of high switching losses by hard switching and transformer losses (copper and iron losses) by high turns-ratio of the transformer. In the proposed converter, primary side switches are turned on at zero voltage switching (ZCS) condition and turned off at zero current switching (ZVS) condition through parallel resonance between secondary leakage inductance of the transformer and a resonant capacitor. Therefore the proposed push-pull converter decreases the switching loss using soft switching of the primary switches. Also, the turns-ratio of the transformer can be reduced by half using a voltage-doubler of secondary side. The theoretical analysis of the proposed converter is verified by simulation and experimental results.