• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.139-144
• /
• 2003

To apply CFT members into the bridge girders, bending behavior of CFT is to be investigated. However, pure bending tests of CFT have been rarely performed, while much of the experimental study of CFT focuses on the axial loading. In this study, ultimate bending strength of CFTs with various different thicknesses and diameters was measured and compared with behaviors of bare tubes. It shows the beneficial effect of concrete for CFT in flexure to increase strength and ductility.

• Computers and Concrete
• /
• 제30권5호
• /
• pp.311-321
• /
• 2022

The interfacial bond strength of partially encased composite (PEC) structure tends to 0, therefore, the cast-in-place concrete theoretically cannot embody better composite effect than the fabricated structure. A total of 12 specimens were designed and experimented to investigate the energy dissipation and damage of fabricated PEC beam through unidirectional cyclic loading test. Because the concrete on both sides of the web was relatively independent, some specimens showed obvious asymmetric concrete damage, which led to specimens bearing torsion effect at the later stage of loading. Based on the concept of the ideal elastoplastic model of uniaxial tensile steel and the principle of equivalent energy dissipation, the energy dissipation ductility coefficient is proposed, which can simultaneously reflect the deformability and bearing capacity. In view of the whole deformation of the beam, the calculation formula of energy dissipation is put forward, and the energy dissipation and its proportion of shear-bending region and pure bending region are calculated respectively. The energy dissipation efficiency of the pure bending region is significantly higher than that of the shear-bending region. The setting of the screw arbors is conducive to improving the energy dissipation capacity of the specimens. Under the condition of setting the screw arbors and meeting the reasonable shear span ratio, reducing the concrete pouring thickness can lighten the deadweight of the component and improve the comprehensive benefit, and will not have an adverse impact on the energy dissipation capacity of the beam. A damage model is proposed to quantify the damage changes of PEC beams under cyclic load, which can accurately reflect the load damage and deformation damage.

• Structural Engineering and Mechanics
• /
• 제33권2호
• /
• pp.137-158
• /
• 2009

This paper investigates the behavior of reinforced concrete (RC) circular columns under combined loading including torsion. The main variables considered in this study are the ratio of torsional moment to bending moment (T/M) and the level of detailing for moderate and high seismicity (low and high transverse reinforcement/spiral ratio). This paper presents the results of tests on seven columns subjected to cyclic bending and shear, cyclic torsion, and various levels of combined cyclic bending, shear, and torsion. Columns under combined loading were tested at T/M ratios of 0.2 and 0.4. These columns were reinforced with two spiral reinforcement ratios of 0.73% and 1.32%. Similarly, the columns subjected to pure torsion were tested with two spiral reinforcement ratios of 0.73% and 1.32%. This study examined the significance of proper detailing, and spiral reinforcement ratio and its effect on the torsional resistance under combined loading. The test results demonstrate that both the flexural and torsional capacities are decreased due to the effect of combined loading. Furthermore, they show a significant change in the failure mode and deformation characteristics depending on the spiral reinforcement ratio. The increase in spiral reinforcement ratio also led to significant improvement in strength and ductility.

• 한국산학기술학회논문지
• /
• 제10권8호
• /
• pp.2038-2043
• /
• 2009

본 연구는 유한요소해석을 이용하여 순수 휨이 작용하는 T형 단면보의 탄성 횡-비틀림 좌굴강도에 대해 기술하고 있다. 유한요소해석을 통해 얻어진 결과는 AISC-LRFD(2007)설계기준과 비교되었으며, 검토결과 AISC-LRFD 제안식을 이용하여 얻어지는 값들이 유한요소해석 결과보다 큰 값을 나타내고 있어 안전측 설계를 유도하고 있지 못하고 있다. 이에 본 연구에서는 수정된 설계 계산식을 제안하고 예제를 통해 활용성을 검토하였다. 새로운 설계 계산식은 T형보의 횡-비틀림 좌굴강도 산정에 쉽게 적용될 수 있으며, 다양한 하중이 작용하는 경우 T형보의 연구에 적극 활용 될 수 있을 것이다.

• 대한기계학회논문집A
• /
• 제39권5호
• /
• pp.453-460
• /
• 2015

후쿠시마 원전 사고 이후로 원자력 발전 플랜트의 배관 시스템에 가해지는 비틀림 하중의 영향에 대한 연구가 여러 연구자들에 의해서 수행되었다. 발전 플랜트의 원주방향 균열을 포함한 배관은 정상운전 조건이나 갑자기 발생한 사고에 의해서 굽힘과 비틀림과 같은 하중을 받을 수 있다. ASME 코드에서는 균열 배관의 구조건전성 확보를 위해서 한계하중 기법을 사용해서 완전소성 파단에 대한 결함평가를 제공한다. 최근 개정된 코드에 따르면, 복합하중은 막응력과 굽힘 응력만을 포함하고 있다. 실제로 운전 환경에서 비틀림 하중이 가해질 수 있음에도 불구하고, 비틀림 하중을 평가하는 방법론에 대해서는 언급하지 않았다. 본 논문에서는 한계하중 분석을 기반으로 원주방향 균열 존재하는 배관에 단순 굽힘과 단순 비틀림, 인장을 포함한 굽힘 비틀림 복합하중이 가해질 경우에 대한 유한요소해석 결과를 포함하고 있다. 전단면 완전항복 기준을 만족하는 한계하중 이론해를 제안하고 유한요소해석을 통해서 이를 검증하였다.

• Steel and Composite Structures
• /
• 제32권4호
• /
• pp.521-536
• /
• 2019

The mechanical response of concrete-filled steel tubular (CFST) columns subjected to pure compression or uniaxial bending was studied in depth over the last decades. However, the available research results on CFST columns under biaxial bending are still scarce and the lack of experimental tests for this loading situation is evident. At the same time, the design provisions in Eurocode 4 Part 1.1 for verifying the stability of CFST columns under biaxial bending make use of a simplistic interaction curve, which needs to be revised. This paper presents the outcome of a numerical investigation on slender CFST columns subjected to biaxial bending. Eccentricities differing in minor and major axis, as well as varying end moment ratios are considered in the numerical model. A parametric study is conducted for assessing the current design guidelines of EN1994-1-1. Different aspect ratios, member slenderness, reinforcement ratios and load eccentricities are studied, covering both constant and variable bending moment distribution. The numerical results are subsequently compared to the design provisions of EN1994-1- 1, showing that the current interaction equation results overly conservative. An alternative interaction equation is developed by the authors, leading to a more accurate yet conservative proposal.

• Structural Engineering and Mechanics
• /
• 제48권2호
• /
• pp.275-289
• /
• 2013

The cross sections of multi-span beams are sometimes suddenly increased at the interior support of continuous beams to resist high negative moment. An earlier study on elastic lateral torsional buckling of stepped beams was conducted to propose new design equations. This research aims to continue the earlier study by considering the effect of inelastic buckling of stepped beams subjected to pure bending and general loading condition. A three-dimensional finite element-program ABAQUS and a statistical program MINITAB were used in the development of new design equations. The inelastic lateral torsional buckling strengths of 36 and 27 models for singly and doubly stepped beams, respectively, were investigated. The general loading condition consists of 15 loading cases based on the number of inflection point within the unbraced length of the stepped beams. The combined effects of residual stresses and geometrical imperfection were also considered to evaluate the inelastic buckling strengths. The proposed equations in this study will definitely improve current design methods for the inelastic lateral-torsional buckling of stepped beams and will increase efficiency in building and bridge design.

• 대한조선학회논문집
• /
• 제52권4호
• /
• pp.349-355
• /
• 2015

Through the recent accident, the checking of ultimate hull girder capacity for container ship should be needed. Smith’s method is well known as the only simplified method to access rapidly for ultimate hull girder capacity except very expensive nonlinear F.E approach. This simplified method, however, is admitted to apply only to bulker and tanker in accordance with Classification Rules up to now. The targets of this study are to verify effectiveness of the simplified method for container ship’s ultimate hull girder strength and to propose the safety factor considering the local bending in double bottom structures due to out of plane loads through the nonlinear F.E analyses. Two different sized ships and three loading conditions which are pure bending, homo-loading and one-bay empty condition were used for this study. Based on the F.E results, the present study showed that CSR’s simplified method is available for the ultimate hull girder strength of container ship and over 1.2 of safety factor should be applied to consider the local bending effect in double bottom structures due to out of plane loads such as sea pressure an cargo.

• Structural Engineering and Mechanics
• /
• 제78권3호
• /
• pp.231-253
• /
• 2021

Pure bending loading conditions are not frequently occurred in practical engineering, but the flexural researches are important since it's the basis of mechanical property researches under complex loading. Hence, the objective of this paper is to investigate the flexural behavior of concrete-filled rectangular steel tube (CFRT) through combined experimental and numerical studies. Flexural tests were conducted to investigate the mechanical performance of CFRT under bending. The load vs. deflection curves during the loading process was analyzed in detail. All the specimens behaved in a very ductile manner. Besides, based on the experimental result, the composite action between the steel tube and core concrete was studies and examined. Furthermore, the feasibility and accuracy of the numerical method was verified by comparing the computed results with experimental observations. The full curves analysis on the moment vs. curvature curves was further conducted, where the development of the stress and strain redistribution in the steel tube and core concrete was clarified comprehensively. It should be noted that there existed bond slip between the core concrete and steel tube during the loading process. And then, an extensive parametric study, including the steel strength, concrete strength, steel ratio and aspect ratio, was performed. Finally, design formula to calculate the ultimate moment and flexural stiffness of CFRTs were presented. The predicted results showed satisfactory agreement with the experimental and FE results. Additionally, the difference between the experimental/FE and predicted results using the related design codes were illustrated.

• 한국산학기술학회논문지
• /
• 제10권5호
• /
• pp.1020-1025
• /
• 2009

본 연구에서는 유한요소해석을 통하여 순수휨을 받는 계단식 변단면 일축대칭 I형보의 탄성 횡-비틀림 좌굴강도 산정법에 대해 설계식 개발이 수행되었다. 유한요소해석결과는 새로운 강도계산식 개발에 활용되었으며, 제안된 강도식은 해석결과와 잘 일치하는 결과를 나타내었다. 새로운 좌굴강도 제안식은 해석결과와 비교하여 $-11%{\sim}2%$의 오차범위를 나타내고 있으며, 모멘트 구매계수가 고려되지 않는다면 간편하게 안전측으로 설계에 적극 활용 가능하다. 또한, 다양한 하중 즉 집중하중, 등분포하중, 및 일련의 집중하중이 작용하는 일축대칭 변단면 부재의 좌굴강도 산정식 개발에 크게 기여하게 될 것이다.