• Journal of the Korea Convergence Society
• /
• v.8 no.11
• /
• pp.307-312
• /
• 2017

In the industry, galvanizing using the principle of sacrificial anode is used Zn-Ni alloy plating was developed as one of the measures to increase the corrosion resistance rather than pure zinc plating. The alloy plating layer has a corrosion resistance of 4-5 times that of the pure zinc plating layer, so that it is applied to automotive parts requiring high corrosion resistance even though the plating cost is high. The amount of Zn-Ni alloy plating solution is a sulfuric acid bath, a chlorinated bath, an alkali bath, and an ammonia bath. Here, the influence of the electrolytic conditions on the composition of the alloy plating in the chloride bath was investigated. The results are explained by the cathode overvoltage and the diffusion coefficient. In general, as the overvoltage of the cathode increases, the concentration polarization becomes more important than the activation polarization. The concentration polarization is determined by element diffusion in the diffusion layer. That is, as the overvoltage of the cathode increases, the Zn content having a large diffusion coefficient increases.

• Journal of the Korean institute of surface engineering
• /
• v.53 no.1
• /
• pp.1-8
• /
• 2020

Sulfamate-chloride baths were fabricated to study the properties of the electrodeposited Ni and NiCo thin films. The dependences of current efficiency, deposit composition of Ni and Co, residual stress, surface morphology and microstructure of electrodeposited Ni and NiCo thin films on CoCl₂ concentration in sulfamate-chloride baths were investigated. The current efficiency was measured to be more than about 90%, independent of the changes of CoCl₂ concentration in the baths. Residual stress of Ni and NiCo thin films was increased from about 45 to about 250 MPa with varying CoCl₂ concentration from 0 to 0.210 M CoCl₂ in the baths and then reached to a plateau, about 250 MPa above 0.420 M CoCl₂ concentration. Nodular surface morphologies were observed at most CoCl₂ concentrations in the baths except 0.210 M. NiCo thin film electrodeposited from the bath with 0.210 M CoCl₂ concentration showed an acicular surface morphology. Pure Ni thin film consists of FCC(111), FCC(200), FCC(220), and FCC(311) peaks without any preferred orientation. On the other hand NiCo thin films make up of HCP(100), FCC(111), HCP(101), FCC(200), FCC(220) or HCP(110), FCC(311) or HCP(112) and FCC(222) peaks. It was revealed from the analysis of XRD result that FCC(111) peak at the NiCo thin film electrodeposited from the bath with 0.084 M CoCl₂ concentration can be regarded as the preferred orientation. However the peak of the preferred orientation was changed to FCC(220) or HCP(110) above 0.084 M CoCl₂ concentration in the baths. Then the intensity of FCC(220) or HCP(110) peak was gradually decreased with increasing CoCl₂ concentration further. The crystalline size of pure Ni thin film was observed to be about 53 ㎛ and those of NiCo thin films were in the range of 35~45 ㎛.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.611-614
• /
• 2005

In this paper, investigated is the relationship between the formation temperature and the thermal stability of Ni silicide formed with Ni-V (Nickel Vanadium) alloy target. The sheet resistance after the formation of Ni silicide with the Ni-V showed stable characteristic up to RTP temperature of $700\;^{\circ}C$ while degradation of sheet resistance started at that temperature in case of pure-Ni. Moreover, the Ni silicide with Ni-V indicated more thermally stable characteristic after the post-silicidation annealing. It is further found that the thermal robustness of Ni silicide with Ni-V was highly dependent on the formation temperature. With the increased silicidation temperature (around $700\;^{\circ}C$), the more thermally stable Ni silicide was formed than that of low temperature case using the Ni-V.

• Journal of the Korean Electrochemical Society
• /
• v.13 no.3
• /
• pp.203-210
• /
• 2010

NiO is commonly used as the cathode for the molten carbonate fuel cell due to its stability and high electrical conductivity in molten carbonates and oxygen atmosphere. However, long-term operation of MCFC has a serious problem which is the degradation of cathode material, the so-called Ni dissolution. In the present study, we have attempted to synthesize a new alternative cathode material as Co/Nb-coated NiO cathode. The results obtained in this study suggest that the Co/Nb-coated NiO cathode can be utilized as having lower dissolution and higher cell performance than those of the pure NiO cathode.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.2
• /
• pp.47-51
• /
• 2008

In this paper, thermal stability of Nickel silicide formed on p-type silicon wafer using Ni-V alloy film was studied. As compared with pure Ni, Ni-V shows better thermal stability. The addition of Vanadium suppresses the phase transition of NiSi to $NiSi_2$ effectively. Ni-V single structure shows the best thermal stability compared with the other Ni-silicide using TiN and Co/TiN capping layers. To enhance the thermal stability up to $650^{\circ}C$ and find out the optimal thickness of Ni silicide, different thickness of Ni-V was also investigated in this work.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.17-18
• /
• 2008

In this paper, 1%-nitrogen doped Nickel was used for improvement of thermal stability of Ni-Germanide. Proposed Ni-N(1%)/TiN structure has shown better thermal stability, sheet resistance and less agglomeration characteristic than pure Ni/TiN structure. During the germanidation process, it is believed that the nitrogen atoms in the deposited nickel layer can suppress the agglomeration of Ni germanide by retarding the diffusion of Ni atoms toward silicon layer, hence improve the thermal stability of Ni-germanide.

• Journal of the Korean Society for Heat Treatment
• /
• v.20 no.4
• /
• pp.187-194
• /
• 2007

A transmission electron microscope (TEM) investigation has been performed on the precipitation of $L2_1$-type $Ni_2AlTi$ phase in B2-ordered NiAl system. The hardness after solution treatment is high in NiAl-Ti alloys suggesting the large contribution of solid solution strengthening in this alloy system. However, the amount of age hardening is not large as compared to the large microstructural variations during aging. At the beginning of aging, the $L2_1$-type $Ni_2AlTi$ precipitates keep a lattice coherency with the NiAl matrix. By longer periods of aging $Ni_2AlTi$ precipitates lose their coherency and change their morphology to the globular ones surrounded by misfit dislocations. Misfit dislocations, which are observed on {100} planes of H-precipitates have the Burgers vector of a <100> with a pure edge type. The lattice misfits of NiAl-$Ni_2AlTi$ system is estimated from the spacings of misfit dislocations to be 1.1% at 1273 K. The lattice misfits decrease with increasing aging temperature in this system.

• Journal of the Korean Electrochemical Society
• /
• v.5 no.3
• /
• pp.125-130
• /
• 2002

An attempt was made for the application of porous reticular metal to a heat dissipation material in semiconductor process. For this aim, the electrodeposition of Fe/Ni alloy on the porous reticular Cu has been performed to minimize the thermal expansion mismatch between Cu skeleton and electronic chip. Preliminary tests for the electrodeposition of Fe/Ni alloy layer were conducted by using standard Hull Cell to examine the effect of current density on the composition of alloy layer. It seemed that mass transfer affected significantly the composition of Fe/Ni layer due to anomalous codeposition in the electrodeposition of Fe/Ni alloy. A paddle type stirring bath, which was employed to control the mass transfer of electrolyte in the work, was found to allow the electrodeposition Fe/Ni with a precise composition. result showed that the thermal expansion of Fe/Ni alloy layer was much lower than that of pure copper. From the tests of heat dissipation by using the apparatus designed in the work the heat dissipation material fabricated in the work showed the excellent heat dissipation capacity, namely, more than two times as compared to that of pure copper plate.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.201-201
• /
• 2003

It has been well known that Ni-MILC TFTs are acceptable for operation of LCD devices but still decrease of annealing temperature is desirable for the future devices like LCD on the plastic substrate. In this work, Cu was added to Ni-MILC in an attempt to lower the annealing temperature and enhance the MILC rate. It has been found that even small amount of Cu addition enhances the MlLC rate considerably. Also well One MILC can be distinguished from island type, which cannot be observed in pure Ni-MILC. Poly TFTs were fabricated with Cu/Ni-MILC and the effects of copper addition on the electrical properties were carefully investigated.

• Journal of the Korean institute of surface engineering
• /
• v.27 no.3
• /
• pp.166-175
• /
• 1994

The effect of Co addition on the electrochemical performance and structural stability of porous Ni anode for molten carbonate fuel cell(MCFC) was evaluated by the anodic polarization and the sintering test in the simulated MCFC anode condition ($650^{\circ}C$, 80% $H_2$+20%$CO_2$). The anode current density ranged from 110mA/$cm^2$ to 144mA/$cm^2$ was obtained at +100mV overpotential by additions of Co up to 10 wt.%. The sintering resistance of Ni-Co anodes was higher than that of the pure Ni anode. The increase of sintering resistance seemed to be to the lower diffusion coefficient of Co than that of Ni.