• Korean Journal of Optics and Photonics
• /
• v.15 no.3
• /
• pp.263-267
• /
• 2004

We have investigated the characteristics of a Nd:YAG laser pumped by a cw Ti:sapphire laser. When the pumping power of the Ti:sapphire laser was 850 ㎽, the maximum output power of the Nd:YAG laser was 450 ㎽. As a result, the slope efficiency for the output power of the Nd:YAG laser was measured to be 56%. We have also investigated the characteristics of a passively Q-switched Nd:YAG laser by using a Cr$^{4+}$:YAG as saturable absorber with initial transmission of 90%. The maximum average output power of 200 ㎽ was obtained with repetition rate of 23.8 KHz and pulse width of 17.0 ns.

• Journal of ILASS-Korea
• /
• v.22 no.2
• /
• pp.69-79
• /
• 2017

When designing a redox flow battery system, compression of battery stack is required to prevent leakage of electrolyte and to reduce contact resistance between cell components. In addition, stack compression leads to deformation of the porous carbon electrode, which results in lower porosity and smaller cross-sectional area for electrolyte flow. In this paper, we investigate the effects of electrode compression on the cell performance by applying multi-dimensional, transient model of all-vanadium redox flow battery (VRFB). Simulation result reveals that large compression leads to greater pressure drop throughout the electrodes, which requires large pumping power to circulate electrolyte while lowered ohmic resistance results in better power capability of the battery. Also, cell compression results in imbalance between anolyte and catholyte and convective crossover of vanadium ions through the separator due to large pressure difference between negative and positive electrodes. Although it is predicted that the battery power is quickly improved due to the reduced ohmic resistance, the capacity decay of the battery is accelerated in the long term operation when the battery cell is compressed. Therefore, it is important to optimize the battery performance by taking trade-off between power and capacity when designing VRFB system.

• Nuclear Engineering and Technology
• /
• v.53 no.6
• /
• pp.1786-1795
• /
• 2021

Printed Circuit Heat Exchanger (PCHE) is a widely used heat exchanger in the supercritical carbon dioxide (sCO₂) Brayton cycle because it can work under high temperature and pressure, and has been a hot topic in Next Generation Nuclear Plant (NGNP) projects for use as recuperators and condensers. Most previous studies focused on channel structures or shapes. However, no clear advancement has so far been seen in the allover size of the PCHE. In this paper, we proposed an optimal size of the PCHE with a fixed volume. Two boundary conditions of PCHE were simulated, respectively. When the volume of PCHE was fixed, the heat transfer rate and pressure loss were picked as the optimization objectives. The Pareto front was obtained by the Multi-objective optimization procedure. We got the optimized number of PCHE channels under two different boundary conditions from the Pareto front. The comprehensive performance can be increased by 5.3% while holding in the same volume. The numerical results from this study can be used to improve the design of PCHE with straight channels.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.6
• /
• pp.513-518
• /
• 2015

Salinity gradient power (SGP) has attracted significant attention because of its high potential. In this study, we evaluate reverse electrodialysis (RED) with various compositions of available resources. The polarization curve (I-V characteristics) shows linear behavior, and therefore the power density curve has a parabolic shape. We measure the power density with varying compartment thicknesses and inlet flow rates. The gross power density increases with decreasing compartment thickness and increasing flow rate. The net power density, which is the gross power density minus the pumping power, has a maximum value at a compartment thickness of 0.2 mm and an inlet flow rate of 22.5 mL/min. The power density in RED is also evaluated with compositions of desalination brines, seawater, river water, wastewater, and brackish water. A maximum power density of $1.75W/m^2$ is obtained when brine discharged from forward osmosis (FO) and river water are used as the concentrated and the diluted solutions, respectively.

• International journal of advanced smart convergence
• /
• v.4 no.1
• /
• pp.104-113
• /
• 2015

This paper focuses on a temperature effects on a PV panel which has been installed in Thailand. The main objective is cleaning PV panels and reduce temperature of PV panel by water injects from waterway and experimental results of PV power what it is difference. This project is designed by PLC control system which water injects and control PV temperature, In addition, this project consists of hardware and software such as water pump, water injection and PLC control has been automatically and it can be control system manually. The automatic control system is working when PV temperature rises up over 45 degree Celsius after that the pumping machine would inject water to the surface of PV panels and it must be stop when the PV panel temperature comes down less than 45 degree Celsius. The result of actual experimental found that the control system has been done correctly under specify condition. The experimental has been shown electrical data before and after water injects on PV system found that the electrical power a bit increases and The energy has been taken from PV panel less than energy consumption equipment of control system which taken to operate the water injecting system.

• New & Renewable Energy
• /
• v.6 no.3
• /
• pp.22-29
• /
• 2010

The concept of Ocean Thermal Energy Conversion (OTEC) is simple and various types of OTEC have been proposed and tried. However the location of OTEC is limited because OTEC requires $20^{\circ}C$ of temperature difference as a minimum, so most of OTEC plants were constructed and experimented in tropical oceans. To solve this we proposed the modified OTEC which uses condenser discharged thermal energy of existing fossil or nuclear power plants. We call this system CTEC (Condenser Thermal Energy Conversion) as this system directly uses $32^{\circ}C$ partially saturated steam in condenser instead of $20{\sim}25^{\circ}C$ surface sea water as heat source. Increased temperature difference can improve thermal efficiency of Rankine cycle, but CTEC should be located near existing plant condenser and the length of cold water pipe between CTEC and deep cold sea water also increase. So friction loss also increases. Calculated result shows the change of efficiency, pumping power, net power and other parameters of modeled 7.9 MW CTEC at given condition. The calculated efficiency of CTEC is little larger than that of typical OTEC as expected. By proper location and optimization, CTEC could be considered another competitive renewable energy system.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.8
• /
• pp.801-806
• /
• 2015

The experimental analysis of a crevice-type vapor chamber heat pipe (CVCHP) is investigated. The heat source of the CVCHP is a high-power light-emitting diode (LED). The CVCHP, which exhibits a bubble pumping effect, is used for heat dissipation in a high-heat-flux system. The working fluid is R-141b, and its charging ratio was set at 60 vol.% of the vapor chamber in a heat pipe. The total thermal conductivity of the falling-liquid-film-type model, which was a modified model, was 24% larger than that of the conventional model in the LED package. Flow visualization results indicated that bubbles grew larger as they combined. These combined bubbles pushed the working fluid to the top, partially wetting the heat-transfer area. The thermal resistance between the vapor chamber and tube in the modified design decreased by approximately 32%. The overall results demonstrated the better heat dissipation upon cooling of the high-power LED package.

• International Journal of Railway
• /
• v.7 no.2
• /
• pp.35-39
• /
• 2014

Urban subways are one of the main parts of urban transportation networks in every city that always requires much attention in order to improve its efficiency in aspects of safety, reliability speed and costs. As the viewpoint of costs, an accurate design, especially design of vertical alignment, can have a dominant role to reduce the costs of urban railway projects. This paper seeks to evaluate the advantages and disadvantages of designing chain vertical alignment for urban subways in compare to flat vertical alignment. To achieve this goal, line A of Qom subway in Iran was selected as a case study in this research. Five parameters considered in the technical-economical evaluation: (1) energy consumption, (2) rolling stock, (3) operation, (4) civil works and geotechnical and (5) hydrological, drainage and pumping. According to the results, a power saving of about 40% have been estimated in the chain vertical alignment for the train without regenerative braking in compare with the flat vertical alignment, although the power saving was calculated less than 10% for the train with regenerative braking. Finally it was found that due to the modern rolling stock technology, the chain vertical alignment represents fewer advantages in compare to the past years.

• Korean Journal of Optics and Photonics
• /
• v.9 no.4
• /
• pp.231-235
• /
• 1998

Passively Q-switched, laser diode(LD) end-pumped Nd:YAG laser was demonstrated by using $Cr^{4+}$:YAG as a saturable absorber. In addition , we could calculate an excitation efficiency, which is an important parameter to evaluate the pumping geometry, directly by measuring the absorbed power in Nd:YAG at threshold condition. We found that output parameters such as average power, pulse duration, and repetition rate strongly depended on the low intensity transmission of $Cr^{4+}$:YAG and driving current of lase diode. The maximum Q-switched output power of 1 W was obtained with 40 kHz repetition rate. The pulse duration was varied from 50 ns to 200 ns.

• Current Optics and Photonics
• /
• v.3 no.1
• /
• pp.33-39
• /
• 2019

We report development of a frequency-stabilized mid-infrared continuous-wave (cw) optical parametric oscillator (OPO) based on a fan-out grating MgO:PPLN crystal pumped at 1064 nm. The OPO resonator was designed as a pump-enhanced standing-wave cavity that resonates to the pump and signal beams. To realize stable operation of the OPO, we applied a modified Pound-Drever-Hall technique, which is a well-known method for powerful laser frequency stabilization. Tuning a poling period of the fan-out grating of the crystal allows wavelength-tunable OPO outputs from 1510 nm to 1852 nm and from 2500 nm to 3600 nm for signal and idler beams, respectively. At the idler wavelengths of 2500 nm, 3000 nm and 3500 nm, we achieved more than 50 mW of output powers at a pumping power of 1.1 W. The long-term stability of the OPO was confirmed by recording the power and wavelength variations of the idler for an hour.