• Journal of Advanced Marine Engineering and Technology
• /
• 제24권5호
• /
• pp.103-110
• /
• 2000

A two phase compound jet, which mixes pulverized solid particles with the air in the test section, is experimentally analyzed in this study. Two phase flow is jetted 10 degree upward in the primary jet, while the secondary jet utilizes the air only. The height difference between the primary and secondary central axises is 32.5mm. The velocity vector field, concentration field, and turbulent properties of solid particles are measured by using 3-Dimensional Particles Dynamics Analyzer. When the jet angle of the secondary jet goes into effect, the solid particle recirculation zone becomes larger. Also, solid particle concentration becomes more dense due to a velocity decrement of particles.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권1호
• /
• pp.88-93
• /
• 2000

In this study, the mixing process of two-phase flow generated by two jets with height difference is analyzed. The primary jet is jetted on the condition of the state mixed pulverized solid particles with air. The height difference between the main jet and the secondary jet is changed into three kinds(0, 32.5, 47.5mm). The velocity vector field, concentration field and turbulent properties of solid particles are measured by using 3-Dimensional Particles Dynamics Analyzer. As the height difference of two jets through the two nozzles increases, the solid particle recirculation zone and the dense zone in the combustion chamber become large. The solid particle concentration at the center of the combustion chamber gets dense because the particle velocity remains slow due to the existence of the solid particle recirculation zone. The particle concentration in the combustion chamber can also be influenced by the hight difference of two jets.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권4호
• /
• pp.515-521
• /
• 1998

In this study the mixing process of two-phase flow which makes two jets existing vlocity difference are analyzed. The primary jet is jetted on the condition of the state mixed pulverized solid pariticle with air and the velocity in the secondary jet is changed into three kinds velocities(0.60, 75m/s) The velocity vector field concentration field and turbulent properties of solid particles are measured by using 3-Dimensional Particles Dynamics Analyzer. As the velocity of secondary jet increases the solid particle recirculation zone becomes larger. Also solid particle concentration gets dense due to velocity decrement of particles.

• 설비공학논문집
• /
• 제4권4호
• /
• pp.299-305
• /
• 1992

Saltation occurs in horizontal flow of solid and gas when the carrier gas velocity is small enough to permit enough to settling of the solid particles within the transport line. So we should examine the pneumatic flow system to lessen the unbured carbon in the power plant. In this paper the saltation velocity was studied on the various solid flow rate in the constant pipe diameter and on the various temperatures of the flow gas. The air velocity in the power plant transport lines was also surveyed in order to compare with the saltation velocity. As the solid flow rate increased in the constant diameter, saltation velocity increased and as the temperater of the flow gas inereased in the transport line, saltation velocity also increased.

• 대한환경공학회지
• /
• 제22권10호
• /
• pp.1881-1891
• /
• 2000

석탄화력 발전소에서 석탄이 연소되면서 생성된 석탄회 중 Cenosphere는 속이 비어 있거나 미세 입자들로 채워져 있고 입자의 크기가 큰 구형의 입자로 물에 부유할 정도로 비중이 작을뿐만 아니라 입자의 벽면에 유리질 성분이 많은 입자이다. 본 연구는 Cenosphere 입자에 대한 형성메카니즘을 분석하여 형태적, 물리적, 화학적 특성을 파악하였다. Cenosphere는 석탄이 연소하면서 입자의 내부에서 발생된 가스가 밖으로 방출되면서 형성되기 때문에 입자가 부풀어져 크게 되고 가스의 분출로 입자의 표변에 구멍이 발생하며 알루미노실리케이트 (Aluminosilicate) 성분에 의해 형성된 기포가 용융표면층에 부착되어 Cenosphere내부에 미세 입자들을 형성한다. 이와 같온 입자의 형성메카니즘 특성 때문에 분말성이 좋으면서 가볍고 큰 입자를 형성한다. Cenosphere의 입도분포는 $100{\sim}200{\mu}m$에 집중된 Single Modal로 질량중앙직경은 $123.11{\mu}m$이고 비중은 $0.67g/cm^3$, 분말도는 $1,135g/cm^3$으로 분석되었다. 또한 Cenosphere의 입자를 구성하는 성분 중 $SiO_2$는 59.17%, $Al_2O_3$는 30.16%로 전체의 89.33%를 차지하고 있고 있어 알루미노실리케이트 성분, 즉 유리질 성분이 높아 열절연성이 뛰어나다. 따라서 Cenosphere 입자를 실리카 바인더로 입자를 결합하면 다양한 온도에서 사용할 수 있는 우수한 열절연체를 만들 수 있어 재활용 원료로 활용이 가능하다.

• 대한기계학회논문집B
• /
• 제27권11호
• /
• pp.1604-1611
• /
• 2003

The experimental investigation of a coal splitter used in the 500㎿(e) boilers of fossil power plant is carried out to validate the design criteria. To predict air flow and the amount of particles at the exit, velocity and the weight of particles are measured on test planes using the coal splitter model with two-dimensional phase doppler particle analyzer and the glass fiber filter. It is found that the position of guide plate influences significantly both flow rates of gas and particle at the exit. Gas flow rate was a linear function of the guide plate, whereas particle flow rate was a exponential function of it.

• Journal of Electrochemical Science and Technology
• /
• 제12권1호
• /
• pp.126-136
• /
• 2021

The electrochemical performance of all-solid-state cells (ASSCs) based on sulfide electrolytes is critically affected by the undesirable interfacial reactions between oxide cathodes and sulfide electrolytes because of the high reactivity of sulfide electrolytes. Based on the concept that the interfacial reactions are highly dependent on the type of sulfide electrolyte, the electrochemical properties of the ASSCs prepared using three types of sulfide electrolytes were observed and compared. The Li2MoO4-LiI coating layer was also introduced to suppress the interfacial reactions. The cells using argyrodite electrolyte exhibited a higher capacity and Coulombic efficiency than the cells using 75Li2S-22P2S5-3Li2SO4 and Li7P3S11 electrolytes, indicating that the argyrodite electrolyte is less reactive with cathodes than other electrolytes. Moreover, the introduction of Li2MoO4-LiI coating on the cathode surface significantly enhanced the electrochemical performance of ASSCs because of the protection of coating layer. Pulverization of argyrodite electrolyte is also effective in increasing the capacity of cells because the smaller size of electrolyte particles improved the contact stability between the cathode and the sulfide electrolyte. The cyclic performance of cells was also enhanced by pulverized electrolyte, which is also associated with improved contact stability at the cathode/electrolyte. These results show that the introduction of Li2MoO4-LiI coating and the use of pulverized sulfide electrolyte can exhibit a synergic effect of suppressed interfacial reaction by the coating layer and improved contact stability owing to the small particle size of electrolyte.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1668-1671
• /
• 2005

Vulcanized natural rubber was pulverized using a single screw extruder in a non-cryogenic Solid Shear Extrusion process where rubber granulates were subjected to high compressive and shear stresses. The producted particles had diameters ranging from 40 to 1200$\{mu}m$. A principle used in this paper was developed in Russia. The development method for producing a polymeric material powder consists in compressing said material by shearing the material during a pressure increase and cooling. Consecutive breakdown is carried out by shearing the material during the pressure decrease and cooling.

• 공업화학
• /
• 제16권5호
• /
• pp.648-652
• /
• 2005

대기압하에서 소결이 어렵다고 알려진 초이온 전도체인 $K^+$-beta-aluminas를 attrition mill을 이용하여 약 350 nm의 평균 입도를 가지는 분말로 분쇄한 후, 시편을 일축가압 성형하여 상압 하에서 동일조성의 분위기 분말을 이용하여 소결하였다. 소결온도는 $1400^{\circ}C{\sim}1650^{\circ}C$까지 $50^{\circ}C$ 간격으로 소결하였으며, 각 소결온도에서 시간에 따른 소결특성을 살펴보았다. 또한 고온에서 입자 성장 속도를 조절하기 위하여 $1600^{\circ}C$에서 zone sintering을 실시하였다. $1600^{\circ}C$와 $1650^{\circ}C$에서 소결한 경우와 $1600^{\circ}C$에서 zone sintering한 시편의 경우, 각각 약 93%와 95%의 소결 밀도를 나타내었다. $1600^{\circ}C$ 이상의 온도에서 2 h 이상 장시간 소결할 경우, 입자의 거대성장으로 인하여 소결밀도가 90% 미만으로 감소하였다.

• 한국분말재료학회지
• /
• 제9권6호
• /
• pp.394-408
• /
• 2002

Nanostructured high strength metastable Al-, Mg- and Ti-based alloys containing different amorphous, quasicrystalline and nanocrystalline phases are synthesized by non-equilibrium processing techniques. Such alloys can be prepared by quenching from the melt or by powder metallurgy techniques. This paper focuses on one hand on mechanically alloyed and ball milled powders containing different volume fractions of amorphous or nano-(quasi)crystalline phases, consolidated bulk specimens and, on the other hand. on cast specimens containing different constituent phases with different length-scale. As one example. $Mg_{55}Y_{15}Cu_{30}$- based metallic glass matrix composites are produced by mechanical alloying of elemental powder mixtures containing up to 30 vol.% $Y_2O_3$ particles. The comparison with the particle-free metallic glass reveals that the nanosized second phase oxide particles do not significantly affect the glass-forming ability upon mechanical alloying despite some limited particle dissolution. A supercooled liquid region with an extension of about 50 K can be maintained in the presence of the oxides. The distinct viscosity decrease in the supercooled liquid regime allows to consolidate the powders into bulk samples by uniaxial hot pressing. The $Y_2O_3$ additions increase the mechanical strength of the composites compared to the $Mg_{55}Y_{15}Cu_{30}$ metallic glass. The second example deals with Al-Mn-Ce and Al-Cu-Fe composites with quasicrystalline particles as reinforcements, which are prepared by quenching from the melt and by powder metallurgy. $Al_{98-x}Mn_xCe_2$ (x =5,6,7) melt-spun ribbons containing a major quasicrystalline phase coexisting with an Al-matrix on a nanometer scale are pulverized by ball milling. The powders are consolidated by hot extrusion. Grain growth during consolidation causes the formation of a micrometer-scale microstructure. Mechanical alloying of $Al_{63}Cu_{25}Fe_{12}$ leads to single-phase quasicrystalline powders. which are blended with different volume fractions of pure Al-powder and hot extruded forming $Al_{100-x}$$(Al_{0.63}Cu_{0.25}Fe_{0.12})_x$ (x = 40,50,60,80) micrometer-scale composites. Compression test data reveal a high yield strength of ${\sigma}_y{\geq}$700 MPa and a ductility of ${\varepsilon}_{pl}{\geq}$5% for than the Al-Mn-Ce bulk samples. The strength level of the Al-Cu-Fe alloys is ${\sigma}_y{\leq}$550 MPa significantly lower. By the addition of different amounts of aluminum, the mechanical properties can be tuned to a wide range. Finally, a bulk metallic glass-forming Ti-Cu-Ni-Sn alloy with in situ formed composite microstructure prepared by both centrifugal and injection casting presents more than 6% plastic strain under compressive stress at room temperature. The in situ formed composite contains dendritic hcp Ti solid solution precipitates and a few $Ti_3Sn,\;{\beta}$-(Cu, Sn) grains dispersed in a glassy matrix. The composite micro- structure can avoid the development of the highly localized shear bands typical for the room temperature defor-mation of monolithic glasses. Instead, widely developed shear bands with evident protuberance are observed. resulting in significant yielding and homogeneous plastic deformation over the entire sample.