• Structural Monitoring and Maintenance
• /
• v.2 no.4
• /
• pp.383-397
• /
• 2015

This article identifies and addresses current limitations on the use of numerical models for validation and/or calibration of damage detection methodologies that are based on the analysis of the high frequency response of the structure to identify the occurrence of abrupt anomalies. Distributed-plasticity non-linear fiber-based models in combination with experimental data from a full-scale reinforced concrete column test are used to point out current modeling techniques limitations. It was found that the numerical model was capable of reproducing the global and local response of the structure at a wide range of inelastic demands, including the occurrences of rebar ruptures. However, when abrupt sudden damage occurs, like rebar fracture, a high frequency pulse is detected in the accelerations recorded in the structure that the numerical model is incapable of reproducing. Since the occurrence of such pulse is fundamental on the detection of damage, it is proposed to add this effect to the simulated response before it is used for validation purposes.

• Structural Engineering and Mechanics
• /
• v.42 no.3
• /
• pp.363-381
• /
• 2012

This study is aimed at providing an efficient analytical model to obtain pressure- impulse diagram of one-way reinforced concrete slabs subjected to different shapes of air blast loading using single degree of freedom method (SDOF). A tri-linear elastic perfectly plastic SDOF model has been used to obtain the pressure-impulse diagram to correlate the blast pressure and the corresponding concrete flexural damage. In order to capture the response history for the slab, a new approximately SDOF method based on the conventional SDOF method is proposed and validated using published test data. The influences of pulse loading shape on the pressure-impulse diagram are studied. Based on the results, a pressure-impulse diagram generation method using SDOF and an analytical equation for the pressure-impulse diagram is proposed to different damage levels and different blast loading shapes.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.3
• /
• pp.52-60
• /
• 1993

Fluttering ghost which is the most severs picture impairment in mobile TV reception under multipath fading environments can be detected by measuring the dynamic variation of the synchronizing pulse timing. And also, the occurrence-stucture of fluttering ghost are directly correlated with the multipath parameters. This paper describes the quantitative evaluating method of the mobile TV pictures impaired by multipath parameters by means of the spectral analysis of synchronizing timing fluctuation. The ghost-flutter curve derived from the spatial amplitue spectrum of synchronizing pulse timing fluctuation express well the spatial variation characteristic, and it has been found to be the quantitative evaluating measure of picture impairment in mobile reception. A correspondence between the ghost-flutter curve (and/or index) and picture quality opinion test results is established.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 1999.04a
• /
• pp.186-195
• /
• 1999

This study is focused on the design and performance test of an earthquake simulator using stepping motor. Stepping motor which controls the motion accurately with generated pulses is applied to the earthquake simulator. Earthquakes like El Centro and Taft are used as inputs to the earthquake simulator. First the number of pulses are calculated and sent to pulse generator, . Then the generator controls the simulator according to the pulse sings, It is shown that the measured signals from the simulator are in very good agreement with input signals of scale-downed earthquakes of El Centro and Taft. This simulator will be used for the experimental study of small-scaled building structures with tuned mass dampers under earthquakes.

• Journal of Surface Science and Engineering
• /
• v.50 no.6
• /
• pp.432-438
• /
• 2017

AZ91D casting alloy requires an advanced plasma anodizing processing because large amount of defects are liable to generate during anodization. In this study, plasma electrolytic oxidation (PEO) of AZ91D Mg alloy was conducted by the application of either constant voltage or current using a pulse mode and its effects on pore formation, surface roughness and corrosion resistance were investigated. The PEO films showed a three-layer structure. The PEO film thickness was found to increase linearly with voltage. The surface roughness, Ra, ranged between $0.2{\mu}m$ and $0.3{\mu}m$. The corrosion resistance increased from RN 3.5 to 9.5 by the PEO treatment when evaluated according to the 72 hour salt spray test. The PEO-treated surface exhibited higher pitting potential than the raw material.

• Journal of the Korean Institute of Navigation
• /
• v.5 no.2
• /
• pp.41-47
• /
• 1981

Many new radar techniques have appeared on the electronic scene in recent years, such as a variety of automatic computer processing. However, even with the advent of these sophisticated radar techniques, an old problem continues to plague all radars: the problem of transmission line losses. With the higher performance required today, the Waveguide testing and trouble-shooting techniques remain essentially unchanged in principle. This paper dealt with the rf pulse "Time-domain Reflectometry" to inspect radar wave-guide system and compared with the conventional methods. During the investigation, it was verified that the pulsed TDR for wave-guide is superior to the conventional methods; 1. Disassembling is not needed to locate the discontinity points and measure the reflections of trobled points. 2. The results of the data are more precise. 3. The condition of individual component is able to the photographed and recorded permanently. 4. Since rf pulse TDR is based on the well-known basic radar principle, such a test set requires the minimum of training to operate. With the level of transmission line problems, the prospect of increasing complexity of equipment, and no relief in sight, the benifits must be emphasizied to adopt such a testing procedure.procedure.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.987-989
• /
• 1993

In this paper, the characteristics of an arc-type linear pulse motor(ALPM) with permanent magnet are analysed using analytical and 2-D finite element method. To verify the analysing method. An ALPM which can be used as actuators of servo systems is designed and constructed. The stator of the ALPM has a permanent magnet and 4 pole exciters in order to provide a detent and thrust force. It's rotor radius is 70 mm and average torque of 60 $N{\cdot}cm$. The test results of the prototype ALPM have reasonably good agreement with those of analytic solutions.

• Proceedings of the KIEE Conference
• /
• 2001.10a
• /
• pp.137-139
• /
• 2001

This paper describes a new methods of detecting rotor position in SRM(switched reluctance motor). The Conventional method of position sensorless control for SRM is measuring phase current and pulse voltage applied in unexcited phase. The estimation of rotor position based on the detection of inductance by pulse current. Implementation is via low-cost electronic circuits with DSP320F241. Test results show that this technique is a possible approach to detect the rotor position of an SRM.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.3
• /
• pp.157-164
• /
• 2003

The pulse-echo method is one of the most widely used ultrasonic techniques for application of nondestructive evaluation. Particularly, quantitative nondestructive evaluation of defects has been considered more important to assure the reliability and the safety of structure. Frequency energy in adhesive joints is based on the ultrasonic wave analysis. The attenuation coefficient upon wave amplitude and the frequency energy that is expressed in the term of wave pressure amplitude were utilized for the primary wave experiment. By means of a control experiment, it was confirmed that the variation of the frequency energy in adhesive joints depends on transition by stress variation. In this paper, the ultrasonic characteristics were measured for single lap joint and Double Cantilever Beam specimen with different fracture modes that was subjected to stress. Consequently, the data that was obtained from the adhesive specimen was analytically compared to the fracture mechanics parameter

• International Journal of Advanced Culture Technology
• /
• v.8 no.4
• /
• pp.95-100
• /
• 2020

Recently, the problem of hypoxia caused by jogging is attracting attention. To solve this problem, this paper proposed a new solution. This paper proved that as a vocalization method of reading aloud, it is possible to increase air intake and activate lung function to exchange more air and obtain more oxygen. Then, blood oxygen saturation was used as an evaluation index for the body's oxygen content level to prove its effectiveness. A photoelectric pulse oximeter developed on the basis of different light absorption principles in blood was used to test blood oxygen saturation. Experimental results show that a certain degree of hypoxia is induced when a lot of oxygen is required due to jogging. Therefore, it was proved that the new vocal breathing method by reading books can increase the blood oxygen saturation of the body and improve the hypoxia of the body. Reading vocal breathing is a simple and efficient oxygen saturation recovery breathing method.