• Korean Journal of Optics and Photonics
• /
• v.27 no.4
• /
• pp.133-142
• /
• 2016

This paper presents the design and simulation of a three-dimensional pixel-by-pixel scanning light detection and ranging (LIDAR) system with a microelectromechanical system (MEMS) scanning mirror and direct sequence optical code division multiple access (DS-OCDMA) techniques. It measures a frame with $848{\times}480$ pixels at a refresh rate of 60 fps. The emitted laser pulse waves of each pixel are coded with DS-OCDMA techniques. The coded laser pulse waves include the pixel's position in the frame, and a checksum. The LIDAR emits the coded laser pulse waves periodically, without idle listening time to receive returning light at the receiver. The MEMS scanning mirror is used to deflect and steer the coded laser pulse waves to a specific target point. When all the pixels in a frame have been processed, the travel time is used by the pixel-by-pixel scanning LIDAR to generate point cloud data as the measured result.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.7
• /
• pp.711-716
• /
• 2012

The purpose of this study was to investigate how the modulation method affects the effectiveness of eliciting tactile sensations by electrical stimulation. Two methods were employed and the results were compared and analyzed; pulse amplitude modulation (PAM) and pulse width modulation (PWM). Thirty-five healthy subjects participated in the experiments to measure the stimulation intensity that began to elicit a tactile sensation - activation threshold (AT). Constant-current monophasic rectangular pulse trains were employed, and the stimulation intensity was varied from zero until the subject felt any uncomfortable sensation. The step size of the stimulation intensity was 100nC/pulse. After each experiment, the subject described the sensation both quantitatively and qualitatively. The two modulation methods did not make a significant difference as far as the AT values were concerned, but most of the subjects showed 'intra-individual' consistency. Also, it was confirmed that our range of the stimulation parameters enabled us to obtain three major tactile sensations; tickling, pressure and vibration. The results suggested that the stimulation parameters and the modulation type should be selected for each individual and that selective electrical stimulation of the mechanoreceptors needs more diversified researches on the electrode design, multi-channel stimulation protocol, waveforms of the pulse train, etc.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.11
• /
• pp.1653-1660
• /
• 2016

The synthetic aperture rardar (SAR) is an active sensor using microwaves. It transmits a microwave signal, called a chirp pulse, and receives the reflected signal in a moving platform such as satellite and unmanned aerial vehicle. Since this sensor uses microwaves that can penetrate the atmosphere, SAR generates the images regardless of light and weather conditions. However SAR operates on the moving platform, the Doppler shift and the side-looking observation method should be considered. In addtion, a residual image or ghost image can be occurred according to selection of the pulse repetition frequency (PRF). In this paper, a range design of the PRF for the L-band spaceborne SAR system is studied for prevention of SAR image distortion. And the system is studied for prevention of SAR image distortion. And the system parameter and the PRF are calibrated iteratively according to the proposed system design procedure and design constraints. The MATLAB based on SAR system simulator has been developed to verify the validity of calculated PRF. The developed simulator assumes that SAR sensor is operated by the PRF calculated from the design. The results of the simulator show that the targets in image has a valid peak to side-lobe ratio (PSLR) so that the PRF can be used for the spaceborne SAR sensor.

• Asian Oncology Nursing
• /
• v.1 no.2
• /
• pp.204-216
• /
• 2001

The purpose of this study was to test the effects of foot reflexology on pain and mood in patients who have just had a mastectomy. The research design was a nonequivalent control group, non-synchronized design. The participants for this study were 28 patients with breast cancer on first or second day after mastectomy surgery. The first 12 patients were assigned to the control group and the second 16 to the experimental group. The study was conducted from October 28, 2001 to December 22, 2001 on a surgical unit of Y Medical Center in Seoul, Korea. Pain intensity, blood pressure, pulse rate and mood were measured as dependent variables. The instrument used for pain intensity and mood was a 10 cm visual analogue scale. Cronbach alpha for this study was .70. For the experimental group pre and post tests were done immediately before and 15 minutes after completion of foot reflexology. Foot reflexology was performed once for 20 minutes. After the pretest, patients in the control group were instructed to have a quiet time for a 35 minute period and then the post-test was done. The number of participants was small so the data were analyzed by Mann-Whitney U test, and Wilcoxon signed ranks test. The results of this study are as follow : 1. In the experimental group there were significant decreases between the pre and post tests for pain intensity (z=-3.47, p<.001), diastolic blood pressure (z=-2.67, p<.01) and pulse rate (z=-3.44, p<.001) but there was no difference between the two groups on the post test. 2. The systolic blood pressure, diastolic blood pressure and pulse rate were also not significantly different between the experimental group and the control group on the post test. 3. The mood score was significantly improved after foot reflexology(z=-3.52, p=.000) and the difference between the two groups was also significant (u=49.0, p=.03). In conclusion, there was a statistically significant difference in mood between the two groups, but no difference for pain intensity, blood pressure, or pulse rate. However, there were significant differences between the pretest and post-test for pain intensity, diastolic blood pressure and pulse rate in the experimental group. On the basis of the above findings, this study suggests that foot reflexology can be an effective method of relieving pain and improving mood in clinical practice in women who have had mastectomy surgery.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.6
• /
• pp.44-52
• /
• 2017

In this paper, we propose a DFD (Digital Frequency Discriminator) design that has better frequency discrimination and a smaller size. Electronic warfare equipment can analyze different types of radar signal such as those based on Frequency, Pulse Width, Time Of Arrival, Pulse Amplitude, Angle Of Arrival and Modulation On Pulse. In order for electronic warfare equipment to analyze radar signals with a narrow pulse width (less than 100ns), they need to have a special receiver structure called IFM (Instantaneous Frequency Measurement). The DFD (Digital Frequency Discriminator) is usually used for the IFM. Because the existing DFDs are composed of separate circuit devices, they are bulky, heavy, and expensive. To remedy these shortcomings, we use a three delay line ($1{\lambda}$, $4{\lambda}$, $16{\lambda}$) in the DFD, instead of the four delay line ($1{\lambda}$, $4{\lambda}$, $16{\lambda}$, $64{\lambda}$) generally used in the existing DFDs, and apply the microwave integrated circuit method. To enhance the frequency discrimination, we detect the pulse amplitude and perform temperature correction. The proposed DFD has a frequency discrimination error of less than 1.5MHz, affording it better performance than imported DFDs.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.587-592
• /
• 2018

Because the brightness of an AMOLED is determined by the flowing current, each pixel of AMOLED operates via A current driving method. Therefore, it is necessary to supply power to adjust the amount of current according to THE user's requirement for AMOLED driving. In this study, an IP driver block was designed and a simulation was conducted for an AMOLED display, which supplies power as selected by users. The IP driver design focused on regulating the output power due to the OLED characteristics for the diode electric current according to the voltage to be activated by pulse-skipping mode (PSM) under low loads, and 1.5 MHz pulse-width modulation (PWM) for medium/high loads. The IP driver was designed to eliminate the ringing effects appearing from the dis-continue mode (DCM) of the step-up converter. The ringing effects destroy the power switch within the IC, or increase the EMI to the surrounding elements. The IP driver design minimized this through a ringing killer circuit. Mobile applications were considered to enable true shut-down capability by designing the standby current to fall below $1{\mu}A$ to disable it. The driver proposed in this paper can be applied effectively to the same system as the AMOLED display dual power management circuit.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1275-1277
• /
• 1995

We designed and constructed an extremly high power s-band traveling wave resonator for the test of high power microwave components using 80MW pulsed klystron with $4{\mu}s$ pulse width. The 10dB directional coupler for the input power coupling was used, and the ring consists of phase shifter, tuner, H-band, and other microwave components. The designed total electrical length of the system is 10 times of the waveguide wavelength, ${\lambda}_g$=15.3cm, and the measured total insertion loss is 0.15dB. The low power test measurment showed the power multiplication of 14.69. The design goal is to achieve the peak power of 300MW, pulse width $4{\mu}s$ with 30 pulse repetition rate. In this article we discuss the treveling wave resonant ring constructed at the PAL laboratory together with the test results.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.1
• /
• pp.42-49
• /
• 2014

Performance evaluation was carried out for the 70 N-class hydrazine thruster whose design performance had been already verified. The pulse-mode firing test was conducted for the development model thrusters with various thrust chamber diameters. Evaluation was made by the performance parameters such as specific impulse, impulse bit, and characteristic velocity, etc: specific impulse and characteristic velocity were deteriorated as the thrust chamber diameter deviates from a standard model. Consequently, it is revealed that the performance characteristics of standard model is most superior among the test models.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.3
• /
• pp.93-98
• /
• 2003

With the improvement of digital signal processors, digital pulse compressor(DPC) is widely used in radar systems. The DPC can be implemented by using FIR filter algorithm in time domain or FFT algorithm in frequency domain. This paper designs an expansible DPC using multiple DSPs. With ADSP-21060 of Analog Devices Inc., the computation time as a function of the number of received range cells and FIR filter tap is compared and analyzed in time domain using C-language and assembly language. therefore, when radar system parameters are determined, the number of DSP's required to implement DPC can be easily estimated.

• The Journal of the Acoustical Society of Korea
• /
• v.14 no.4
• /
• pp.5-11
• /
• 1995

In this paper, we design the new high-speed seek algorithm which can access the data of disk (in 3.5-inch optical disk drive). When seek the target track on optical disk in high-speed using the ref-T. E(Reference Tracking Error) and sample pulse signal, it's always possible high-speed seek without re-check and compensation for error by the ref_T. E and sample pulse signal. The performance test result is represented as follow ; it is satify the average seek time of 28mses.