• 해양환경안전학회지
• /
• 제13권2호
• /
• pp.169-172
• /
• 2007

본 논문은 Z-형 컨버터와 수정된 공간벡터 PWM인버터로 구성된 분산전원시스템의 회로모델과 제어 알고리즘을 보여주고 있다. Z-형 컨버터는 수동소자인 L과 C로 간단히 구성되어 있으며 인버터의 상하 양 소자가가 동시에 도통되도록 하는 구간을 이용해 승압을 함으로써 기존의 DC/DC 변환기와는 다른 형태를 취하고 있다. 점근 관측기를 이용한 이산시간 슬라이딩모드제어를 통해 전류제어를 함으로써 센서수를 줄이고 제어성능을 개선하였다. 대체에너지로 관심이 많은 태양광이나, 연료전지 그리고 소형 풍력발전으로부터 생산된 직류 에너지를 상용으로 사용할 수 있도록 하는 전력변환기로써 유용하게 사용될 수 있을 것이다.

• 대한의용생체공학회:의공학회지
• /
• 제32권3호
• /
• pp.264-269
• /
• 2011

To increase therapeutic efficiency and biological safety, it is important to precision control of acoustic output for therapeutic ultrasound equipment. In this paper, the electro-acoustic radiation conductance, one of electroacoustic characteristics of therapeutic ultrasound equipment, was measured by the radiation force balance method according to IEC 61161 standards and the acoustic output was estimated using the electro-acoustic radiation conductance. The estimation of acoustic output was conducted to continuous wave mode and pulse wave mode of duty cycle between 20% and 80%. The differences between prediction values and measurement results are within 5% of measurement uncertainty, which is a reasonably good agreement. The results show that acoustic output controlled by electro-acoustic radiation conductance was found to be an effective method.

• 한국통신학회논문지
• /
• 제19권5호
• /
• pp.796-804
• /
• 1994

본 논문은 Inverse SAR를 이용하여 속도를 모르는 움직이는 물체의 영상 이미지를 얻는 이미징 알고리즘을 제시하였고 실제 데이터를 알고리즘에 적용되었다. 실제 데이터는 stepped-frequency 변조된 레이더 신호를 송신하였고 수신된 데이터는 sampling rate이 충분하지 않으나 reference 신호를 mixing 시켜 unaliased 되게 만든 후 interpolation 에 의해서 해결하였다. 알고리즘을 적용시키는데 요구되는 물체의 속도는 subaperture processing 방법에 의해서 얻어졌으며 얻어진 속도에 의해서 squint-mode SAR geometry 로 변환한 후 최근에 제시된 approximation 이 없는 이미징 알고리즘을 사용하여 최종적으로 이미지를 얻게 되었다. 또한 ISAR가 데이터를 송수신 하는 동안 물체의 속도가 변하는 경우 이것을 보상하는 방법을 제시하였다.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제51권10호
• /
• pp.587-594
• /
• 2002

A low frequency square wave electronic ballast for the high intensity discharge(HID) lamps using fuzzy logic controller is developed. This electronic ballast consists a buck converter, a low frequency square wave full bridge inverter, a high voltage pulse generator for the HID lamp ignition, an over current protection circuit and an 8-bit microcontroller. The ballast system is operated on the constant current mode during the HID lamp start-up process and the system is operated on the constant power mode during steady state. Experimental results show that the fuzzy logic control operation is carried out successfully by the 8-bit microcontroller PIC16F877 In this electronic ballast system, in spite of the limited control bandwidth caused by low operating speed of the microcontroller, the good performance in the constant lamp current characteristic is obtained. Acoustic resonance of the HID lamps can be effectively avoided because the instantaneous In lamp power is fully constant due to the low frequency square wave drive.

• 한국추진공학회지
• /
• 제8권4호
• /
• pp.84-90
• /
• 2004

추진제 주입압력 350 psia 에서 0.95 lbf 의 정상상태 공칭추력을 내는 단일액체추진제 하이드라진 추력기의 성능평가 결과를 추력, 임펄스 비트, 비추력 등을 통하여 제시한다. 연소시험 형상과 절차에 대한 간략한 묘사와 더불어 정상상태 연소모드로부터 얻어지는 추진제 공급압력. 질량유량, 추력기 작동환경 진공도, 그리고 추력 등의 변이거동에 대한 전형적인 결과를 검토한다. 제시된 추력기 성능은 1-lbf급 표준형 단일추진제 로켓엔진의 기준성능에 성공적으로 비교된다. 선별된 추력기군을 위성체 추진시스템의 비행모델로 채택하기 위한 추력기간 성능편차에 대해 부연한다.

• Archives of Pharmacal Research
• /
• 제29권5호
• /
• pp.412-417
• /
• 2006

Triamcinolone acetonide (TA) is a corticosteroid that is used in the systemic and topical treatment of many inflammatory diseases. In this study, a phonophoretic drug delivery system was designed to enhance the TA permeability and the influence of ultrasound was examined. In order to establish the transdermal delivery system for TA, a hydrophilic carbopol gel containing TA was prepared after adopting phonophoresis. A permeation study through mouse skin was performed at $37^{\circ}C$ using a Franz diffusion cell, and the ultrasound treatment was carried out for 10 h. The level of TA permeation through the skin was evaluated under various ultrasound conditions including the frequency (1.0, 3.0 MHz), intensity (1.0, $2.5W/cm^2 $), and duty cycle (continuous, pulse mode) using a 0.5% TA gel. The highest permeation was observed under the ultrasound treatment conditions of low frequency, high intensity, and in continuous mode.

• Journal of Electrical Engineering and Technology
• /
• 제13권1호
• /
• pp.201-210
• /
• 2018

This paper proposes a new start-up method for a load commutated inverter (LCI) in a large synchronous gas-turbine generator. The initial rotor position for start-up torque is detected by the proposed initial angle detector, which consists of an integrator and a phase-locked loop. The initial rotor position is accurately detected within 150ms, and the angle difference between the real position and the detected position is less than 1%. The LCI system operates in two modes (forced commutation mode and natural commutation mode) according to operating speed range. The proposed controllers include a forced commutation controller for the low-speed range, a PI speed controller and a PI current controller, where the forced commutation controller is connected to the current controller in parallel. The current controller is modeled by Matlab/Simulink, where a six-pulse delay of the thyristor and a processing delay are considered by using a zero-order hold. The performance of the proposed start-up method is evaluated in Matlab/Psim at standstill and at low speed. To verify the feasibility of the method, a 5kVA LCI system prototype is implemented, and the proposed initial angle detector and the system performance are confirmed by experimental results from standstill to 900rpm.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권8호
• /
• pp.407-414
• /
• 2004

In this paper, a new gray scale expression method that divides the scan lines into multiple blocks is suggested. The proposed method can drive 16 sub-fields per 1 TV field in the panel with XGA ($1366{\times}768$) resolution. The on and off states of even subfields depend on the condition of odd subfields. The write address mode is used in the odd subfields, while the erase address mode is used in the even subfields. Because the ramp reset pulse is applied every 2 sub-fields, both the contrast ratio and the dynamic voltage margin are sufficiently obtained in comparison with previous AWD (Address While Display) methods. In realizing 16 subfields, shortening the scan time in the erase address period was important. The X bias voltage in the erase address period affected the minimum address voltage but did not the delay time of the address discharge. The delay time of the address discharge was affected by the address voltage and the time interval between the last sustain discharge and the scanning time. We also evaluated the dynamic false contour. New method shows an improved image quality in horizontal moving, but discontinuous lines were observed at the boundaries of each block in vertical moving

• Journal of Power Electronics
• /
• 제15권1호
• /
• pp.10-17
• /
• 2015

A quasi-constant on-time controlled buck front end in combined discontinuous conduction mode and boundary conduction mode is proposed to improve power factor (PF).When instantaneous AC input voltage is lower than the output bus voltage per period, the buck converter turns into buck-boost converter with the addition of a level comparator to compare input voltage and output voltage. The gate drive voltage is provided by an additional oscillator during distortion time to eliminate the cross-over distortion of the input current. This high PF comes from the avoidance of the input current distortion, thereby enabling energy to be delivered constantly. This paper presents a series analysis of controlling techniques and efficiency, PF, and total harmonic distortion. A comparison in terms of efficiency and PF between the proposed converter and a previous work is performed. The specifications of the converter include the following: input AC voltage is from 90V to 264V, output DC voltage is 80V, and output power is 94W.This converter can achieve PF of 98.74% and efficiency of 97.21% in 220V AC input voltage process.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.2103-2105
• /
• 2005

Metal film type of resistor have been tested to invest maximum usable power at the pulsed high voltage and pulsed high current. Experiments were carried out using capacitor charging power supply and dump switch. Pulsed amplitude were varied from 1kV to 25kV. The peak current reached was 1kA. Datasheet are given for the limited pulsed power and energy for metal film type of resistor in nanosecond and microsecond time range. The experimental investigation of the threshold loading of the resistor in the high current and voltage pulsed mode has shown that the process of destruction of resistor has specific features for each mode. The mechanisms of failure and destruction of resistors under action of high-voltage and high-current pulses are discussed.