• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.8
• /
• pp.843-849
• /
• 2009

The reliable operation of a swing check valve in the main feed water system of a power plant is most essential for successful shout-down process. A failure to close the valve at proper time often leads to the instability of the main feed water system, or even to an emergency stop of the power plant. In reality it is a very difficult task to monitor the behavior of a swing check valve. Furthermore it is impossible to see the motion of the valve. In this work two measurements were carried out simultaneously to determine the precise valve closure time. The dynamic pressure measurements were made at the inlet and outlet regions of the swing check valve. The transient vibration of the valve housing in the direction of water flow was also measured, which enabled the measurement of the transient vibration of the valve housing near valve closure. By comparing the results produced from these measurements the precise valve closure time could be determined. By carrying out order tracking technique using the dynamic pressure signals and pump rpm signal, the complicated dynamic problems inside the main feed water system can be more easily dealt with. This measurement scheme might be implemented in a power plant on a real-time basis without much difficulty. If this could be implemented, valuable information essential for shut-down operations can readily be passed on to the main control room. The feasibility of this implementation was demonstrated by this experimental work.

• Journal of Korean Academy of Nursing
• /
• v.16 no.2
• /
• pp.13-28
• /
• 1986

The main purpose of th study was to evaluate he validity of Korean Pain Measurement Tool composed of pain terms. The specific purposes of this study were 1. to examine whether pain intensities of pain terms are congruent with those classified in three previous studies. 2. to evaluate the relative intensity of each term by panel of judges. 3. to explore the difference of ranks of pain terms according to the sex, education, and ages. One hundred and sixty normal individuals were selected by 2$\times$2$\times$4 sampling design. Sex (male, female), education (high school, college), and age (20s, 30s, 40s, 50s) were matched. Each individual was asked to rate the ranks of 3~8 pain terms in each subclass. The data measured by ordinal scale were transformed to the interval scale to compare with the pain intensities gained from the previous study. The pain ranks different from previous results were finally rearranged or cancelled through the consultation of 4 panel of judges and sunmed up to 91 pain terms in the scale. As a result, the ranks of pain terms within each of eleven subclasses among the twenty subclasses completely were congruent with the Previous pain ranks, while the ranks of nine subclasses were different from the previous pain ranks. In addition, there was significant relation between sex and pain ranks in skin punctuate pressure pain and cavity pressure. (sp : $\chi$$^2$=5.18 ø=0.26； cp : $\chi$$^2$=5.83 ø=0.24) In conclusion, seven terms from subclasses of inflammatory repeated pain, traction pressure pain, fatigue-related pain, fear-related pain, dull pain, and pulsation. related pain were cancelled. The ranks of four terms in subclasses of incisive Pressure pain and constrictive pressure pain were tentatively rearranged. Ranks of two terms in the tract pain were left as shown in the third study. As a result, six terms must be studied repeatedly for obtaining exact scores from ratio scale.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.37-44
• /
• 2021

In this study, shape design and material selection were carried out for a two-stage pressure-reducing regulator to compensate for the shortcomings of a one-stage mechanical decompression regulator. The shape of the contact surface of the depressurization unit was considered, material was selected, and the shape was designed to compensate for the pulsation and slow response through the two-stage decompression and to solve the problem of high pressure deviation. In terms of airtightness, the deformation amount of TPU showed a small amount of displacement of up to 15.82%. Considering the fact that it is applicable to various hydrogen fuel supply systems by securing universality by applying electronic solenoids to the second pressure reduction, magnetic materials were selected. The hydrogen embrittlement and corrosion resistance were evaluated to verify the plating process. Surface corrosion did not occur in only the case of Cr plating. The elongation during the corrosion process was compared using a tensile test, and there was a difference within 2%.

• 한국연소학회:학술대회논문집
• /
• 2004.11a
• /
• pp.206-212
• /
• 2004

It is necessary to consider the stability, economic environmental-friendly problems by the development of the road, supply of the automobile, environmental problem as designing the exhaust system. To reduce the noise and the vibration of the automobile, it is needed to consider the pulsation noise, air current noise, vibration of air pipe which generate the intake and exhaust noise of the automobile. Moreover, the discharge sounds, intake sound, radiation sound, transmitted sound are occurred. To reduce this influence, the variable valve is needed and to control these factors, path transformation muffler and active type muffler are needed. While engine efficiency could be reduced with this transformationand resistance by the pressure, thermal property. In this study, how to design exhaust systems yielding higher condversion efficiency, lower backpressure and optimize the performance. this study is recommended for exhaust system and designers and engineers involved in SI engine exhaust system and it will furnish information for you to design more efficient.

• The Journal of the Society of Korean Medicine Diagnostics
• /
• v.12 no.2
• /
• pp.8-17
• /
• 2008

Objectives: For the traditional pulse diagnosis in Oriental Medicine, not only the pulse shape in time domain, but the width, length and depth of arterial pulse also should be measured. However, conventional pulse diagnostic systems have failed to measure the spatial parameters of the arterial pulse e.g. effective length of arterial pulse in the wrist. In fact, there are many ways to measure that kind of spatial features in arterial pulsation, but among them, the method using image sensor provides relatively cheap and simple way, therefore I tested feasibility of measuring 2-dimensional pressure distribution by imaging devices. Methods: Using widely used PC cameras and dotted balloons, the subtle oscillation of skin over the radial artery was recorded continuously, and then the displacement of every dot was calculated. Consequently, the time course of that displacements shows arterial pulse wave. Results: By the proposed method I could get pressure distribution map with 30Hz sampling rate, 21steps quantization resolution, and approximately 1mm spatial resolution. With reduced quantization resolution, $3cm{\times}4cm$ view angle could be achieved. Conclusion: Although this method has some limitations, it would be useful method for detecting 2-dimensional features of arterial pulse, and accordingly, this method provides a novel way to detect 'narrow pulse', 'wide pulse', 'long pulse', 'short pulse', and their derivatives.

• The KSFM Journal of Fluid Machinery
• /
• v.11 no.1
• /
• pp.18-25
• /
• 2008

Recent trends of a centrifugal pump are high speed in rotation and high pressure in head with high efficiency to meet the demands of industries. However, the newly developed pumps make trouble of pressure pulsation in the pumping system by performance instability of the pump. Moreover, cavitation, which is a main obstacle of high rotational speed in the pump, occurring in an impeller gives serious damages to the impeller and casing wall. The purpose of present study is not only to develop a simple method to improve pump performance but also to suppress the occurrence of cavitation in the centrifugal pump by use of J-Groove. J-Groove is a shallow groove installed on the casing wall in the meridional direction. The application of J-Groove to a centrifugal pump with a new type impeller of "semi-closed impeller" has proved its effectiveness as a useful countermeasure of the unstable pump performance and cavitation. The results show that the combination of semi-closed impeller and J-Groove can be applied successfully and improves both the pump performance and suction performance.

• Journal of Power System Engineering
• /
• v.14 no.3
• /
• pp.25-32
• /
• 2010

전 세계적으로 급속도로 인기가 더해가고 있는 수소에너지는 높은 전환 효율성, 재생성, 친환경적인 특징을 가지며 미래의 주 에너지가 될 것이다. 왕복동식 압축기를 통과한 후의 수소 가스의 압력은 높은 맥동압을 가진다. 스너버는 압축기의 한 구성품으로 맥동압을 낮추고 수소가스의 불순물을 제거하기 위해 사용된다. 이 연구에서의 실험은 스너버 시스템에 사용된 강관의 맥동에 관해 조사하기 위해서 수행되었다. 맥동압은 12 Hz ~ 60 Hz의 모터속도에서 RMS값을 기준으로 0.1625% ~ 0.5305% 그리고 평균압력을 기준으로 0.1621% ~ 0.5277% 감소하였다. 압력손실은 RMS값을 기준으로 0.1092% ~ 1.4419%, 평균압력을 기준으로 0.1493% ~ 1.7507%로 측정되었다. CFD를 이용한 수치해석값은 실험값이 거의 비슷한 결과를 나타내고 강관 관로 내부 가스의 자세한 압력을 설명하기 위한 중요한 역할을 수행한다.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2000.09a
• /
• pp.251-265
• /
• 2000

S $m_{2}$F $e_{17}$ $N_{x}$ film magnets using a S $m_{2}$F $e_{17}$ target were prepared at $N_{2}$ gas atmosphere using a Nd-YAG laser ablation technique. The effect of nitrogen pressure, deposition temperature, pulsation time and film thickness on the structure and magnetic properties of S $m_{2}$F $e_{17}$ $N_{x}$ film were studied. Increasing the nitrogen pressure up to 5 atm. was confirmed to lead the formation of complete S $m_{2}$F $e_{17}$ $N_{x}$ compound. Optimized magnetic properties with the nitrogenation temperature ranging over 500-53$0^{\circ}C$ could be obtained by extending the nitrogenation time up to 4 hours. Relatively low coercivities of 400~600 Oe were exhibited from the S $m_{2}$F $e_{17}$ $N_{x}$ films having the thickness of 50~100 nm while 4$\pi$ $M_{s}$ of 10~12 kG could be achieved. In-plane anisotropic characteristic, which was the basic goal in this study, was achieved by controlling the nitrogenation parameters.ameters.ers.ameters.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.28-30
• /
• 2012

A mechanical pulsator is manufactured for study of combustion instabilities in a model chamber with impinging-jet injectors. Artificial disturbance is generated by the device and thereby, artificial instability can be examined experimentally. A sample F(fuel)-O(dxidizer)-O-F impinging-jet injector is adopted for the test. The model chamber was designed based on the methodologies proposed in the previous work regarding geometrical dimensions and operating conditions. Pressure fluctuation data, which is obtained from the dynamic pressure transducers installed in combustion chamber, is analyzed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.6
• /
• pp.1062-1065
• /
• 2001

with the splendid development of internet environment Korea is a diverse proving ground and supplies the highest ADSL in the world. This thesis examines the tole-medicine treatment which connects the doctor's computer with the in each house and transmits blood pressure, pulsation, temperature, blood sugar, image picture stethoscope, voice.