• 조명전기설비학회논문지
• /
• 제24권9호
• /
• pp.49-55
• /
• 2010

Many electric poles in the softground have been collapsed due to external load. In this study, 10 types of tests were performed with variation of location, numbers and depths of anchor blocks as well as depth of poles to find stresses acting on concrete electric poles. The stresses of concrete poles are relaxed at 600~700[kg] of tensile load, and stresses are concentrated at top of pole, and spread to lower part of pole. In the concrete pole collapse test, tensile load at failure was approximately 1,400[kg], which is twice of design load. As passive zone in the soil increases, the stresses acting on concrete pole are concentrated at lower part of pole based on moment arm earth pressure distribution.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.245-248
• /
• 2006

The objective of this study is to take the first step in creating a user-friendly health monitoring system for recycled aggregate concrete structure using acoustic emission(AE). Each specimen was a cube, the edge of which was 150mm. For pull-out tests, a steel rebar, 13mm in diameter, was embedded in the center of each specimen and casting directions(i.e., vertical and horizontal) were considered in this paper. The AE parameters were analyzed for damage levels(i.e. internal cracking stage, pull-out stage) of all specimens. Results from this study show that event, duration versus amplitude of a signal, showed a clear difference for different loading stages depending upon the concrete casting directions.

• Restorative Dentistry and Endodontics
• /
• 제44권4호
• /
• pp.37.1-37.10
• /
• 2019

Objectives: This study evaluated the bond strength of various fiberglass post cementation techniques using different resin-based composites. Materials and Methods: The roots from a total of 100 bovine incisors were randomly assigned to 5 treatment groups: G1, post + Scotchbond Multi-Purpose (SBMP) + RelyX ARC luting agent; G2, relined post (Filtek Z250) + SBMP + RelyX ARC; G3, individualized post (Filtek Z250) + SBMP; G4, individualized post (Filtek Bulk-Fill) + SBMP; G5, individualized post (Filtek Bulk-Fill Flow) + SBMP. The samples were subjected to the push-out (n = 10) and pull-out (n = 10) bond strength tests. Data from the push-out bond strength test were analyzed using 2-way analysis of variance (ANOVA) with the Bonferroni post hoc test, and data from the pull-out bond strength test were analyzed using 1-way ANOVA. Results: The data for push-out bond strength presented higher values for G2 and G5, mainly in the cervical and middle thirds, and the data from the apical third showed a lower mean push-out bond strength in all groups. No significant difference was noted for pull-out bond strength among all groups. The most frequent failure modes observed were adhesive failure between dentine and resin and mixed failure. Conclusions: Fiberglass post cementation using restorative and flowable bulk-fill composites with the individualization technique may be a promising alternative to existing methods of post cementation.

• 한국산업보건학회지
• /
• 제21권4호
• /
• pp.209-214
• /
• 2011

Objectives: To assess the risk of pushing or pulling the yarn-carrying cart, the survey was performed in some fiber manufacturing factories. Methods: We selected 6 fiber-twisting factories which agreed to in-site survey of their workplace. To measure both initial and sustained forces of the push-pull tasks, Chatillon CSD500 dynamometer(2004, Ametek, USA) was used. The mean of 3 tests for the same cart was adopted as the measured forces. Height and width of cart, weight of spooled yarns, and distance of movement were also measured. Inspection of cart wheel, moving path, and the actual hand position while moving was done. Results: More than one pushing or pulling task exceeded the push-pull force limits of design goal in 5 factories. Though the cart was not loaded the heaviest weight in the factory, the measured push or pull force exceeded the limits several times. A few cart wheels were worn out and tangled with pieces of yarn. It was also observed some holes in the moving path. Conclusions: While the push-pull task is not included in the 11 scopes of over-burdened work notified by Korean government, it should be recognized as risk factor of work-related musculoskeletal disorders. The maintenance work such as regular change and frequent cleaning of cart wheel, the use of fitting wheel, and flattening of bumpy floor through the moving path should be advised importantly in the worksite management of work-related musculoskeletal disorders.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2003년도 Proceedings of the international symposium on the fusion technology
• /
• pp.122-128
• /
• 2003

Rock bolts are widely used as a supplementary roof support system in hard-rock mining since a long time. Since the performance of fully grouted passive bolts depends on bond strength, in the present investigation extensive laboratory pull-out as well as push-out tests were conducted varying the bolt diameter, length and cement-water mixing ratios of grout. The load-displacement curves were developed and were verified with the numerical results obtained from finite element analysis using ALGOR software. Numerical models were validated for push-out tests and a detailed analysis was carried out to know the displacement, stress, strain distribution along the bolt.

• Tribology and Lubricants
• /
• 제23권6호
• /
• pp.288-297
• /
• 2007

Adhesion and friction tests were carried out in order to investigate the effect of temperature on the tribological characteristics of poly (methylmethacrylate) (PMMA) film using AFM. The pull-off and friction forces on the PMMA film were measured under a high vacuum condition (below $1{\times}10^{-4}$ Pa) as the temperature of the PMMA film was increased from 300 K to 420 K (heating) and decreased to 300K (cooling). Friction tests were also conducted in both high vacuum and air conditions at room temperature. When the temperature was 420 K, which is 25 K higher than the glass transition temperature $(T_g)$ of PMMA, the PMMA film surface became deformable. Subsequently, the pull-off force was proportional to the maximum applied load during the pull-off force measurement. In contrast, when the temperature was under 395 K, the pull-off force showed no correlation to the maximum applied load. The friction force began to increase when the temperature rose above 370 K, which is 25 K lower than the $T_g$ of PMMA, and rapidly increased at 420 K. Decrease of the PMMA film stiffness and plastic deformation of the PMMA film were observed at 420 K in force-displacement curves. After the heating to 420 K, the fiction coefficient was measured under the air condition at room temperature and was found to be lower than that measured before the heating. Additionally, the RMS roughness increased as a result of the heating.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 지반공학 공동 학술발표회
• /
• pp.320-329
• /
• 2005

The use of diverse methods for the retaining system has been continuously increased in order to maintain the stability during excavation. However, ground anchor system occasionally may have the restriction in urban excavation sites nearby the existing structures because of space limitation. In this case, soil nailing system with relatively short length of nails could be efficiently useful as an alternative method. The general soil nailing support system, however, may result in excessive deformations particularly in excavating the zone of weak soils or nearby the existing structures. Therefore, applying the pretension force to the soil nails then could play important roles to reduce deformations mainly in an upper part of the nailed-soil excavation system as well as to improve the local slope stability. In this study, a newly modified soil nailing technology named as the PSN(Pretention Soil Nailing) is developed to reduce both facing displacements and ground surface settlements during top-down excavation process as well as to increase the global slope stability. Up to now, the PSN system has been investigated mainly focusing on an establishment of the design procedure. In the present study, the field tests including pull-out tests were fulfilled to investigate the behavior of characteristics for PSN system. All results of tests were also analyzed to provide a fundamental and efficient design.

• 지질공학
• /
• 제30권4호
• /
• pp.635-648
• /
• 2020

본 연구는 회전관입말뚝의 이음부를 용접이나 볼트가 필요 없는 육각형 이음부로 개선하여 압축재하시험을 수행하였다. 또한 인발시험의 경우 기존 방법과 유사하게 볼트체결 방법으로 적용하여 인발시험을 수행하였다. 회전관입말뚝의 지지력을 평가하기 위해 현장시험 2지역을 선정하였다. 하중재하시험은 정재하시험과 인발시험을 수행하였으며 회전관입말뚝에 대한 지지력을 평가하였다. 현장시험결과, 정재하시험시 중력식 그라우트를 적용한 말뚝에서 AC 358 Code에 따른 지지력평가 결과 600 kN 이상으로 나타났으며, 그라우트가 없는 말뚝에서는 600 kN 이하의 지지력을 보여 중력 그라우팅이 필요함을 확인하였다. 또한 현장시험결과를 고려하여 지지력을 평가하였으며, 적은 표본에 의해서 도출된 결과로 추후 기초자료로 활용될 수 있을 것으로 판단된다.

• 콘크리트학회논문집
• /
• 제13권6호
• /
• pp.593-601
• /
• 2001

철근콘크리트구조에서 철근의 인장력이 발휘되기 위해서는 적절한 정착길이 또는 갈고리가 필요하다. 그런데, 접합부와 같이 배근이 집중되는 곳이나 대구경 고강도철근이 필요한 경우 정착을 위한 정착길이나 갈고리의 제작 및 배근작업이 어려우며 콘크리트의 충진성도 저하될 수 있다. 또한 갈고리부분의 과도한 응력집중으로 국부적인 지압파괴나 slip이 발생될 우려도 있다. 이러한 문제점을 해결할 수 있는 방안으로 정착판을 철근 단부에 부착한 기계적 정착공법이 제안되고 있다. 본 연구는 기계적 정착공법의 기초가 되는 정착장치의 요구성능과 정착설계법을 고찰하고 인발실험를 통해 정착장치의 앵커기능을 확인하고자 한다 인발실험 결과, 본 연구에서 설계된 정착장치는 앵커로써의 기능을 적절히 발휘하여 기존 CCD 이론식과 매우 근접한 내력을 발휘하였다 철근항복내력 이상의 정착내력을 지니는 경우, 항복하중까지 콘크리트에 아무런 손상이 발생되지 않았으며, 정착판 후미에서 콘크리트와의 상대변위는 0.2mm이하로 콘크리트에 손상을 유발시키지 않을 것으로 판단되었다. 따라서, 본 연구의 설계과정으로 제작된 기계적 정착장치를 통해 콘크리트에 유해한 손상 없이 필요한 정착내력을 확보할 수 있다. 그러나, 철근간 간격이 좁아 파괴면이 중첩되는 경우에는 정착내력이 크게 저하되어, 순수한 콘크리트 내력만으로 기계적 정착설계가 이루어지는 경우 상당한 매립깊이가 요구된다. 따라서, 실제 구조물의 정착설계를 위해서는 인접부재와의 골조거동(frame action)에 따른 구속효과와 전단보강근의 영향을 고려할 필요가 있다. 이에 대한 추가적인 연구가 필요하다.

• 콘크리트학회논문집
• /
• 제22권6호
• /
• pp.753-760
• /
• 2010

초고성능 콘크리트(ultra high performance concrete, UHPC)는 종래의 보통 콘크리트와 다른 새로운 재료로써 높은 강도와 향상된 인성을 그 특징으로 한다. 이러한 새로운 재료의 활용을 위하여 이 연구에서 초고성능 콘크리트의 부착 성능을 평가하고자 하였다. 수정된 RILEM 방법을 사용하여 초고성능 콘크리트와 이형 철근의 인발실험(pull-out test)을 수행하였으며 보통 콘크리트와 비교하여 5~10배에 달하는 부착강도를 확인하여 기존의 설계 기준에 비하여 현저하게 감소한 정착길이와 피복 두께를 제안하였다. 700 MPa급 고장력 철근의 실험 결과의 비교로부터 초고성능 콘크리트에서 고강도 철근 활용의 유효성을 확인하였다. 강연선의 응력전달길이 측정실험을 통하여 현재 전달길이 기준이 UHPC의 경우 매우 보수적이라는 것을 확인하였다. 또한 유한요소해석을 통하여 실험 결과를 검증하였다.