• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.225-228
• /
• 2007

Micro solid propellant thruster is the most feasible for development with current MEMS. Basic components of micro solid propellant thruster are diverging nozzle, micro igniter, combustion chamber, and solid propellant. Micro nozzles and micro chambers were fabricated using photosensitive glass by anisotropic wet etching technique. Micro Pt heaters on glass membrane which ignited solid propellant were developed. Components of thruster were integrated. Successful ignition was observed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.378-382
• /
• 2008

A 50 N monopropellant thruster being developed for attitude control in a variety of aerospace application systems is described in this paper. Ninety percent hydrogen peroxide was selected as a propellant, since it is much less hazardous than hydrazine. A scaled down thruster with aluminum oxide loaded with the platinum in the reaction chamber was tested to determine propellant decomposition onto a catalyst. A scaled up 50 N thruster, with a catalyst bed of 3 cm in diameter and 4 cm in length, was evaluated by decomposition efficiency based on temperature, ${\eta}_T$, efficiency of characteristic velocity, ${\eta}_{C^*}$, and measurement of thrust. The performance of a 50 N thruster was 40.5 Newton in thrust, about 100 % in ${\eta}_T$, and 98 % in ${\eta}_{C^*}$, and 125 sec in specific impulse at sea level.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.27-30
• /
• 2005

Hanwha Corporation succeeded in domestic development of thruster heat shield for KOMPSAT-2 propulsion subsystem partly. Thruster heat shield, one of the main components of DTM, is designed to prevent the critical radiative heat exchange between thruster and satellite during firing. To overcome the manufacturing difficulties, an electro-forming process is preferred to classical welding process. In this case, an inner diameter of a new shield will be decreased a little due to the change of manufacturing process. The interference problem between thruster nozzle and heat shield was investigated through structural analysis by KARI. Hanwha manufactured heat shield based on the analysis results. In this paper, full development process is described for design, analysis, manufacturing of heat shield.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.7 no.4
• /
• pp.80-89
• /
• 2003

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.399-402
• /
• 2008

It is well known that helium saturated propellants significantly effects the dynamics of propulsion system, thruster cross coupling, water hammer and thruster performance. Especially for the propulsion systems, which have multiple high thrust engines, such as HTV(H-II transfer vehicle), the effect is more important. Therefore full-saturated propellants should be used at ground tests of HTV propulsion system and evaluate its effects. HTV is an advanced space vehicle being developed by Japan Aerospace Exploration Agency(JAXA) to enhance cargo delivery capabilities of the fleet of vehicles visiting the International Space Station(ISS). This paper presents an overview of the successful effort of the testing with saturated propellants(MMH/MON3) for HTV propulsion system during the ground firing tests.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.245-250
• /
• 2004

The discharge current oscillation has been measured for various hollow anode widths and its axial positions using a 1㎾-class anode layer hall thruster. As a result, there were thresholds of magnetic flux density for stable discharge. The plasma structure inside the hollow anode was numerically analyzed using the fully kinetic 2D3V Particle-in-Cell (PIC) and Direct Simulation Monte Carlo (DSMC) methods. The results reproduced both stable and unstable operation modes. In the stable operation case, which corresponds to the case with low magnetic flux, the plasma penetrated into the hollow anode deeper than the case with higher magnetic flux density case. This suggests that comparably large substantial anode area should contribute to stable operation.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.275-278
• /
• 2010

By changing the nozzle throat area during the operation, thrust of a pintle thruster can be adjusted easily such as a liquid propulsion. In this paper, numerical analysis was carried out for SNECMA's pintle thruster with different pintle shapes. Flow field and aerodynamic load changed drastically with pintle shapes. Bore in the pintle decreased aerodynamic load significantly.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.35-38
• /
• 2003

The purpose of this work is to introduce the 1-N grade thruster development program for attitude control of satellites and lunch vehicle systems. Characteristics of the thruster and its performance have been evaluated through hot-firing test of small liquid engine inside a vacuum test cell. Performance evaluation of thruster were made with a variation of propellant injection pressure at steady state and pulse firing mode, respectively. Also hot-fire test system and test procedure are briefly described, too.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.45-48
• /
• 2007

Conventional force sensors such as piezoelectric sensor has limitations for measuring micro/nano-scale thrust. In this study we developed nano-scale measurement system using laser displacement sensor and cantilever. And electrospray microthruster was fabricated by using stainless capillary and extraction electrode, to generate nano-scale thrust. The measurement system can measure the around 90 nN thrust from this thruster. In addition, we designed and fabricated electrospray micro thruster based on PMMA(Polymethyl methacrylate), which has a nozzle protruded from the substrate.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.147-150
• /
• 2003

The purpose of this research was to develope components of micro solid propellant thruster. Micro solid propellant thruster had four basic components: combustion chamber, nozzle, solid propellant and micro heater for ignition. A performance of micro heater and characteristic of solid propellant was investigated. Micro heater was fabricated by conventional MEMS process and Platinum layer was used for heating element. Effect of geometry parameters on micro heater was tested. The temperature responses of heater with respect to each parameters was compared for a given electrical power. The characteristic of solid propellant(HTPB/AP) was investigated to obtain burning velocity in small chamber. Additionally, a capacity of filling propellant with high viscosity in small chamber was checked to guarantee for the micro fabrication.