• Journal of Ship and Ocean Technology
• /
• v.9 no.1
• /
• pp.1-10
• /
• 2005

The procedures of model test and performance prediction for the CRP-POD propulsion ships, are studied. At the CRP-POD system, which are highly applicable to ultra large container carriers, RPM ratio of two propellers is not fixed, unlike conventional CRP system, and hence the power of each propeller must be predicted respectively. In this paper, a CRP-POD system is designed for 10,000 TEU class ultra large container carriers, and the characteristics of the CRP-POD system are experimentally studied. Finally, based on this study, the procedure of powering performance evaluation for CRP-POD propulsion ships is suggested. However, further studies on quantitative correction of the present procedure are required.

• Journal of the Society of Naval Architects of Korea
• /
• v.59 no.5
• /
• pp.271-279
• /
• 2022

In order to study the self-propulsion test and analysis techniques for the submerged body with pumpjet propulsors in the Large Cavitation Tunnel (LCT), at the Korea Research Institute of Ships and Ocean Engineering, a set of test equipment was designed and manufactured. The pumpjet propulsor is composed of rotor, stator and duct which results in the strong interaction between the components. To measure the thrust and torque for duct and stator, a ring-shaped sensor was applied. The test equipment including pumpjet is installed on the stern of the submerged body. As the whole pumpjet including duct and stator was considered as the propulsor from pumpjet open-water test, the self-propulsion test was conducted in the same way. The total thrust, combined thrust of rotor, duct and stator was used for the pumpjet self-propulsion test analysis. Accordingly, the self-propulsion test and analysis were conducted in the same way as those of the conventional propeller. The full-scale performances of the pumpjet propulsor were compared with those of the reference propeller. On the basis of the present study, it is thought that the pumpjet propulsor would be designed optimally.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.16 no.4
• /
• pp.248-254
• /
• 2013

Recently, contra-rotating propellers (CRP) having higher efficiency draw much attention since the EEDI regulation of IMO has been enforced. In this paper a numerical method based on the vortex lattice potential theory with a wake model and an experimental procedure with a newly built measuring device, specifically focusing on CRPs, are introduced. And they are applied to a series of CRP known to be designed for the purpose of improving EEDI. The numerical and experimental results showed good agreement explaining the characteristics of the CRP properly. The proposed method is believed to be effectively used for various CRP related studies.

• Journal of the Society of Naval Architects of Korea
• /
• v.40 no.5
• /
• pp.1-9
• /
• 2003

To predict the powering performance of full scale ships from the towing tank tests, resistance, propeller open water and self-propulsion tests are conducted. Model tests inevitably include the experimental error defined as the sum of two types of uncertainties, bias and precision errors. The induced errors in each element of model test are propagated through various routes and correlated with one another. The correlation coefficients are very important in the uncertainty analysis. The coefficient gives a direction(increase or decrease) for a value of error in individual elements. If the coefficient is not used accurately, the error bounds of the individual elements are overestimated or underestimated. In this study, the new methodology is applied to the uncertainty analysis of HMRI's towing tank tests, thus error bounds of each element is suggested and verified by several repetitive experiments.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.12 no.1
• /
• pp.843-855
• /
• 2020

X-plane submarines show better maneuverability as they have much longer span of control plane than that of cross plane submarines. In this study, captive model tests were conducted to evaluate the maneuverability of an X-plane submarine using Computational Fluid Dynamics (CFD) and a mathematical maneuvering model. For CFD analysis, SNUFOAM, CFD software specialized in naval hydrodynamics based on the open-source toolkit, OpenFOAM, was applied. A generic submarine Joubert BB2 was selected as a test model, which was modified by Maritime Research Institute Netherlands (MARIN). Captive model tests including propeller open water, resistance, self-propulsion, static drift, horizontal planar motion mechanism and vertical planar motion mechanism tests were carried out to obtain maneuvering coefficients of the submarine. Maneuvering simulations for turning circle tests were performed using the maneuvering coefficients obtained from the captive model tests. The simulated trajectory showed good agreement with that of free running model tests. From the results, it was proved that CFD simulations can be applicable to obtain reliable maneuvering coefficients for X-plane submarines.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.3
• /
• pp.158-166
• /
• 2021

In this paper, a numerical analysis technique using a body force model is investigated to estimate the available net thrust of multi-pod-driven ice-breaking vessels under bollard pull and overload conditions. To employ the body force model in present flow simulations, drag and thrust components acting on the pod unit are calculated by using Propeller Open Water (POW) test data. The available net thrusts according to the direction of operation are evaluated in both bollard pull and overload conditions under deep water. The simulation results are compared with the model test data. The available net thrusts, calculated by the present analysis for ahead operating modes at 3~6 knots which are typical speeds of the target vessel in arctic field, are agreed well with the model test results. It is also found that the present result for astern operating mode appears approximately 6 % larger than the model test result. In addition, the available net thrusts are calculated under the both operating conditions accompanied by shallow water effects, and the main cause of the difference is studied. Based on the result of the present study, it is confirmed that the body force model can be applied to the performance evaluation of multi-pod propulsion system and the main engine selection in early design stage of the vessel.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.26 no.4
• /
• pp.14-26
• /
• 1989

This paper describes the method of statistical analysis and its programs for predicting the ship's powering performance. The equation for the wavemaking resistance coefficient is derived as the sectional area coefficients by using the wavemaking resistance theory and its regression coefficients are determined from the regression analysis of the model test results. The equations for the form factor, wake franction and thrust deduction fraction are derived by purely regression analysis of the principal dimensions, sectional area coefficients and model test results. The statistical analyses are performed using the various descriptive statistic and stepwise regression analysis techniques. The powering performance prognosis program is developed to cover the prediction of resistance coefficients, propulsive coefficients, propeller open-water efficiency and various scale effect corrections.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.3
• /
• pp.41-49
• /
• 1999

A feasibility study is performed for practical application of a Ventilating Water-Jet(VWJ) propulsor which attracts new attention as a candidate propulsor for super-high speed vessels. Super-cavitating foil sections are adopted for the rotor blades since the rotor is operating at ventilating condition. Wedge type and cavitator type foil sections are used for the design of rotor blades. Other geometric characteristics of rotors are selected from the Kaplan type ducted propeller rotors. The test section of KRISO cavitation tunnel is modified to perform open-water tests of the VWJ propulsors. The tests are performed both at fully-submerged and free-jet conditions. Ventilation occurred at the free-jet condition by sucking the air in the downstream side of the rotor, which easily develops as super-cavitation when the rotor operates at lower advance coefficients. Spoilers are attached at the trailing end of the pressure side of the blade section, in order to increase the lift force.

• Journal of Navigation and Port Research
• /
• v.47 no.6
• /
• pp.305-314
• /
• 2023

In this study, a mathematical model of a 9.77 G/T small fishing vessel was established based on captive model tests. The powering and manoeuvring performances of the vessel in the harbor and coastal sea were focused on, so captive model tests were conducted up to the full-scale speed of 8 knots. Propeller open water, resistance, and self-propulsion tests of a 1/3.5-scaled model ship were performed in a towing tank, and the full-scale powering performance was predicted. Hydrodynamic coefficients in the mathematical model were obtained by rudder open water, horizontal planar motion mechanism tests of the same model ship. In particular, in static drift and pure yaw tests which were conducted at a speed of 2 to 8 knots, the linear hydrodynamic coefficients varied with the ship speed. The effect of the ship speed on the linear coefficients was considered in the mathematical model, and manoeuvring motions, such as turning circles and zig-zags, were simulated with various approach speeds and analyzed.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.3
• /
• pp.27-37
• /
• 1997

The paper deals with the effectiveness of various special rudders on course stability of a ship. We adopted five types of rudder, such as one normal rudder and four special rudders, which contain two rudders with concave and convex strips on sides respectively, one flapped rudder, and one rudder with end plates on tips. In the circulating water channel, model test was carried out for measuring lift characteristics of the rudders in open water. And various captive model tests were also carried out for measuring the experimental constants related with helm angle and steering in hull-propeller-rudder system. From the test results, the changes in manoeuvring hydrodynamic derivatives due to adoption of normal and special rudders were predicted. Then course stability performances of a ship with normal and special rudders were evaluated and discussed. As a result, it is clarified that the rudder with concave or convex strips and flapped rudder have no effect on course stability, while the rudder with end plates improves course stability with effect. The result in this study is expected to be used usefully when the course stability is in issue and has to be improved without amendment of hull design at initial design phase or after construction of a ship.