• Aerospace Engineering and Technology
• /
• v.1 no.1
• /
• pp.55-64
• /
• 2002

A conceptual design of propulsion system for a geosynchronous communication satellite with 12 years design life is presented in this paper. Propellant mass budget for the design life is calculated using total velocity increment (ΔV) flowed-down from mission requirement analysis. Sizes of the fuel and oxidizer tank are derived based on the calculated propellant mass budget, and mass of the pressurant as well as the size and pressure of pressurant tank are calculated too. Thruster positioning, number of rocket engines, and position of tank are determined through Trade-Off Study with Structure & Mechanical Subsystem. Propulsion system configuration and its schematics are presented finally.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.1
• /
• pp.28-35
• /
• 2018

In order to analyze the flammability limit and structure of the gaseous methane-gaseous oxygen diffusion flame formed through a shear coaxial injector, combustion experiments were carried out according to the condition of injector recess and propellant mass-flow rate. As a result, it was confirmed that stable anchored flame was observed even at the high oxygen Reynolds number as the propellant momentum flux ratio increased, and that the recess had no significant influence on the flame shape and flammability limit. The anchored flame visualized through a chemiluminescence showed the maximum OH radical emission intensity at a specific position, irrespective of the propellant injection condition, and the radical intensity was greatly reduced by the injector recess.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.121-127
• /
• 2007

Direct acting pressure relief valve applicable to propellant tank of launch vehicle is modeled in this study The flow resistance of the partially opened valve is modeled as a function of the distance of the valve stem from the resting position. The position of the valve varies transiently as a function of its mass, the spring force, sliding friction, and the pressure differential. Choking at valve throat and compressibility are considered for the analysis. This study presents systematic analysis method for pressure relief valve applicable to propellant tank of liquid rocket. The results shows transient flow resistance caused by stem motion and the importance of choking at valve throat for pressure relief valve design.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.4
• /
• pp.98-106
• /
• 2000

A conceptual design of propulsion system for a geosynchronous communication satellite with 12 years design life is presented in this paper. Propellant mass budget for the design life is calculated using total velocity increment ($\Delta$V) flowed-down from mission requirement analysis. Sizes of the fuel and oxidizer tank are derived based on the calculated propellant mass budget, and mass of the pressurant as well as the size and Pressure of pressurant tank are calculated too. Thruster positioning, number of rocket engines, and position of tank are determined through trade-off study with Structure & Mechanical Subsystem. Propulsion system configuration and its schematics are presented finally.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.111-114
• /
• 2009

A catalyst ignitor of small thrust engine using hydrogen peroxide and kerosene was designed and fabricated, which confirmed mass flow rate for design pressure through the water cold-flow test in this study. In order to investigate ignition performance, it was changed that mixture ratio for kerosene mass flow rate in a position which heat of hydrogen peroxide decomposition comes to a steady state. And we confirmed stable ignition property in a wide range of mixture ratio.

• Journal of Aerospace System Engineering
• /
• v.14 no.1
• /
• pp.68-73
• /
• 2020

This purpose of this paper was to review the development trend of the VTOL MAVs with a ducted propellant that can fly like the VTOL at intermediate and high speeds, hovering, landing, and lifting off vertically over urban areas, warships, bridges, and mountainous terrains. The MAV differs in flight characteristics from helicopters and fixed wings in many respects. In addition to enhancing thrust, the duct protects personnel from accidental contact with the spinning rotor. The purpose of the U.S. Army FCS and DARPA's OAV program is spurring development of a the VTOL ducted MAV. Today's MAVs are equipped with video/infrared cameras to hover-and-stare at enemies hidden behind forests and hills for approximately one hour surveillance and reconnaissance. Class-I is a VTOL ducted MAV developed in size and weight that individual soldiers can store in their backpacks. Class-II is the development of an organic VTOL ducted fan MAV with twice the operating time and a wider range of flight than Class-I. MAVs will need to develop to perch-and-stare technology for lengthy operation on the current hover-and-stare. The near future OAV's concept is to expand its mission capability and efficiency with a joint operation that automatically lifts-off, lands, refuels, and recharges on the vehicle's landing pad while the manned-unmanned ground vehicle is in operation. A ducted MAV needs the development of highly accurate relative position technology using low cost and small GPS for automatic lift-off and landing on the landing pad. There is also a need to develop a common command and control architecture that enables the cooperative operation of organisms between a VTOL ducted MAV and a manned-unmanned ground vehicle.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.1
• /
• pp.33-45
• /
• 2019

In this study, numerical simulations were performed to investigate the steady-state characteristics of a symmetric pintle nozzle by varying the position of the pintle and the altitude. The pintle nozzle shape was used in a linear pintle nozzle that had been analyzed prior to the study, and the boundary conditions of the chamber were considered to be according to the propellant burn-back characteristics. A software was used to perform a verification analysis of the square nozzle, pintle nozzle, and high-altitude conditions with an appropriate analytical technique. The pintle position had three different nozzle throat area conditions-: fully closed, half open, and fully open, and the altitude was set at 0, 5, and 20 km. The study compared the thrust, pintle drive load, and static stability at each condition.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.330-339
• /
• 2008

Ground-based interceptors(GBI) comprise a major element of the strategic defense against hostile targets like Intercontinental Ballistic Missiles(ICBM) and reentry vehicles(RV) dispersed from them. An optimum design of the subsystems is required to increase the performance and reliability of these GBI. Propulsion subsystem design and optimization is the motivation for this effort. This paper describes an effort in which an entire GBI missile system, including a multi-stage solid rocket booster, is considered simultaneously in a Genetic Algorithm(GA) performance optimization process. Single goal, constrained optimization is performed. For specified payload and miss distance, time of flight, the most important component in the optimization process is the booster, for its takeoff weight, time of flight, or a combination of the two. The GBI is assumed to be a multistage missile that uses target location data provided by two ground based RF radar sensors and two low earth orbit(LEO) IR sensors. 3Dimensional model is developed for a multistage target with a boost phase acceleration profile that depends on total mass, propellant mass and the specific impulse in the gravity field. The monostatic radar cross section (RCS) data of a three stage ICBM is used. For preliminary design, GBI is assumed to have a fixed initial position from the target launch point and zero launch delay. GBI carries the Kill Vehicle(KV) to an optimal position in space to allow it to complete the intercept. The objective is to design and optimize the propulsion system for the GBI that will fulfill mission requirements and objectives. The KV weight and volume requirements are specified in the problem definition before the optimization is computed. We have considered only continuous design variables, while considering discrete variables as input. Though the number of stages should also be one of the design variables, however, in this paper it is fixed as three. The elite solution from GA is passed on to(Sequential Quadratic Programming) SQP as near optimal guess. The SQP then performs local convergence to identify the minimum mass of the GBI. The performance of the three staged GBI is validated using a ballistic missile intercept scenario modeled in Matlab/SIMULINK.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.4
• /
• pp.85-90
• /
• 2018

The objective of this paper is to observe effects of ignition position and time on ignition transition. A gaseous oxygen and liquid kerosene mixture is used as propellant with a shear-coaxial injector. In order to study the ignition delay time and combustion instability intensity, the pressure transducer was used. Sequences, excepting igniter operation time, were fixed to compare the ignition time only. Initial pressure peak and ignition delay time increased as the ignition time was delayed. Additionally, an unstable flame development zone was detected when the igniter was away from the injector.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.12 no.2
• /
• pp.146-151
• /
• 2009

It is known that muzzle flash can be generated by the reaction between the oxygen in the air and unburned gunpowder contained in the propellant gas if a barrel is not long enough to burn gunpowder fully inside of the barrel. A hugh muzzle flash, which is a characteristic of small arms with short barrel length, disturbs a shooter in aiming at the target at night by making the shooter blind for a while and endangers the shooter's life by revealing firing position to enemies. In addition, the heat of muzzle flash can deteriorate the performance of thermal sights, which are attached to small arms for effective night combat. In this paper, flash suppressors of different shapes were designed for a newly developed 5.56mm caliber rifle with short barrel length and the performance of each flash suppressor to reduce the muzzle flash was compared by on-site test firing. Through the test firing, a highly efficient design of flash suppressor for reducing the muzzle flash was identified. The result of the paper can be referred when designing flash suppressors for small arms with short barrel length.