• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.2
• /
• pp.18-25
• /
• 2017

The study for the combustion characteristics of propellants for nozzleless boosters was carried out. The metal fuels of Al and Zr were introduced into solid propellant formulations in order to enhance the density-specific impulse and the high burning rate with low pressure exponent was investigated as the major combustion characteristic of propellant to design nozzleless boosters. The burning rate of Zr-containing propellant was higher than Al-containing propellant and, $13{\mu}m$ Zr-containing propellant exhibited the burning rate of 35 mm/s (at 1000 psi)and pressure exponent of 0.3282. The benefit of using Al and Zr-containing propellant into nozzleless boosters was demonstrated in these results.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.1
• /
• pp.62-71
• /
• 2015

Geostationary satellites use the thruster in order to control the location change and mount the suitable amount of liquid propellant depending on the operating lifetime. Therefore the lifetime of the geostationary satellite depends on the residual propellant amount and the precise residual propellant gauging is very important for the mitigation of economic losses arised from premature removal of satellite from its orbit, satellites replacement planning, slot management and so on. The propellant gauging methods of geostationary satellite are mostly used PVT method, thermal mass method and bookkeeping method. In this paper, we analysis the modeling of COMS(Communication, Ocean & Meteorological Satellite) bipropellant system for bookkeeping method and COMS GTO(Geostationary Transfer Orbit) injection propellant estimation using Monte-Carlo method.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.1
• /
• pp.88-95
• /
• 2015

This paper considers the effects of propellant mixture ratio and loading errors on the performance of a liquid rocket. Propellant residuals generated by error sources are analyzed for a launch vehicle model whose first stage consists of a cluster rocket of four 75-tonf class engines using a statistical Monte-Carlo approach and then the optimal fuel biases minimizing residuals are computed. The results are validated through comparison with analytic method using approximate formula, which have been applied for other space launch vehicles.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.147-150
• /
• 2003

The purpose of this research was to develope components of micro solid propellant thruster. Micro solid propellant thruster had four basic components: combustion chamber, nozzle, solid propellant and micro heater for ignition. A performance of micro heater and characteristic of solid propellant was investigated. Micro heater was fabricated by conventional MEMS process and Platinum layer was used for heating element. Effect of geometry parameters on micro heater was tested. The temperature responses of heater with respect to each parameters was compared for a given electrical power. The characteristic of solid propellant(HTPB/AP) was investigated to obtain burning velocity in small chamber. Additionally, a capacity of filling propellant with high viscosity in small chamber was checked to guarantee for the micro fabrication.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.1
• /
• pp.71-78
• /
• 2019

This paper describes the formulation and properties of a recently developed energetic thermoplastic (ETPE) propellant, which is composed of 45% of newly synthesized glycidyl azide polymer, energetic plasticizer (DEGDN) and nitramine oxidizer (RDX). Compared to conventional thermoplastic propellants, the new ETPE propellant showed approximately 7% higher performance and exhibited similar mechanical properties but a lower burn rate and a higher pressure exponent.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.2
• /
• pp.26-36
• /
• 2007

The thermal response characteristics of nozzle liner for a solid rocket motor applying highly aluminized PCP or HTPB propellant with slotted tube grain have been investigated. The SEM photographs of aluminum oxide particles taken from nozzle liner show that the PCP propellant with the finer and less contents of oxidizer can offer greater possibility for increasing aluminum agglomeration than the HTPB propellant. The PCP propellant shows locally greater mechanical erosion at 4 circumferential areas of the nozzle entrance in line with grain slot due to the impingement of large particles, but the HTPB propellant shows greater thermochemical ablation at the nozzle blast tube, the throat insert and the exit cone because of relatively much more mole fraction of $H_2O\;and\;CO_2$ in combustion gases.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.1
• /
• pp.78-85
• /
• 1999

Burning characteristics of solid propellants embedded with four kinds of metal wires(Ag, Cu, Al, Ni-Cr wire) were studied with varying wire diameters(O.10.8 mm) lot N-5 propellant. It was found that the order of the burning rate increment ratio($r_w$/$r_sb$) was Ag wire > Cu wire > Al wire> Ni-Cr wire which was the same as the order of the magnitude of thermal diffusivity. The burning rate increment ratio($r_w$/$r_sb$) of N-5 propellant was less than that of composite Propellant because of the difference of adiabatic flame temperature and flame structure. When Ag, Cu and Al wire having high thermal diffusivity were embedded in N-5 propellant, the plateau and mesa characteristics of the double base propellant were disappeared, but not disappeared in the case of propellant embedded with Ni-Cr wire due to its poor thermal conductivity.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.5
• /
• pp.96-106
• /
• 2011

There are many advantages in applying gel propellant to a gel propulsion system. These include higher performances, the energy management of liquid propulsion system, reliable storability and low leakage characteristics. Additionally, gel propulsion system are preferable to the high density impulse of propulsion system. Also, when compared to liquid propellants, the gel propellants acquire greater heat energy. Gel propellants achieve a high specific impulse when metal particles with aluminum and boron are added. With respect to atomization, an inactive process occurs due to the variable viscosity of the metal particles and gelling agents. To improve the defect of atomization and combustion characteristics of gel propellant, a variety of issues related to spray and combustion is introduced here.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.168-171
• /
• 2007

A technical review of current slurry and gelled propellants is presented. In advanced countries, it is confirmed that these propellants have high specific impulse, density, excellent handling, safety characteristics and thrust controllability through research since 1950s. Substantial researches have been pursued to characterize the rheological properties, spray/combustion phenomena and propulsion system design for the gel propellant characteristics. Slurry and gelled propellants are developing actively to applicate both military and space propulsion fields such as tactical missile, air-breathing ramjet, pulse detonation engine, and combined cycle engine of future propulsion mode.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.251-254
• /
• 2006

Micro thruster is a key technology in the micro/nano satellite. MSPT has been attracted attention as a one of possible solution for micro thruster MSPT as a systems four components. It is composed of nozzle, igniter, combustion chamber and propellant. This paper surveys varioud MSPTs which have been reported. The model of MSPT arrays for total impulse of 1 mNs is proposed. Combustion chamber is designed and fabricated.