• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.10
• /
• pp.1377-1384
• /
• 2003

An analysis has been performed for active thermal control of the KOMPSAT monopropellant rocket engine assembly, i.e., dual thruster module(DTM). The main efforts of this work have been directed at determining proper heater sizes for propellant valves and catalyst beds necessary to maintain their temperatures within specified temperature ranges under KOMPSAT environment and operational conditions. The TAS incorporated with TRASYS thermal radiation analyzer was used to establish a complete heat transfer model which allows to predict the DTM temperature as a function of time. The thermal analysis has been performed in transient mode to verify the appropriate power for catalyst bed heaters necessary to increase catalyst bed temperature to the required value within a specified period of time. Similar analysis has been executed to validate the heater power for the thermostatically controlled primary and redundant heater circuits used to prevent hydrazine freezing, i.e., single fault. Moreover the effect of the radiative property of thermal control coating of heat shield was examined. Thruster firing condition was also simulated for the heat soakback condition. As a consequence, all thermal analysis results for DTM satisfactorily met the thermal requirements for the KOMPSAT DTM under the worst case average voltage, i.e. 25 volt.

• Aerospace Engineering and Technology
• /
• v.6 no.1
• /
• pp.190-200
• /
• 2007

A pyrogen type igniter was designed to satisfy the requirements of KSLV-I Kick Motor system. To insure the reliability of the igniter before the production of the flight model, we have been performed the structure, environmental, combustion tests. The hydraulic test was carried out to confirm the strength of the components of the igniter. The shock and vibration tests were considered to check whether the igniter operates normally under the severe environmental condition. The combustion tests were also performed to understand the ignition characteristics with the variation of initial condition. Finally, we confirmed that the igniter could provide the acceptable energy to ignite the propellant of kick motor at the ground test.

• Aerospace Engineering and Technology
• /
• v.7 no.2
• /
• pp.131-143
• /
• 2008

Slag mass deposition was required to predict performance accurately of KSLV-I kick motor(KM) system. The validation of the numerical analysis was performed with mass flow rate measured at 4th ground test of the KM. The study described here included internal flow field of KM at various time steps during burning. Slag mass accumulation was computed through the aluminum oxide particle paths to deviate from the gas flow streamlines in flight. These numerical analysis was performed with Fluent 6.3 program The effects for the acceleration, origins and diameters of the aluminum oxide particles was analyzed, finally the total slag mass accumulation was acquired. We confirmed that the slag mass deposition was agreement well with predicted slag mass based on kick motor the grounded test.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.10
• /
• pp.1026-1030
• /
• 2010

This paper summarizes the activities performed for the development of a BLDC(Brushless Direct Current) motor driven cryogenic thrust control valve with application to KSLV-II rocket engine. The developed thrust control valve can modulate the flow rate of liquid oxygen under cryogenic temperature of 90K and high pressure of 113.2 bar with the help of electro-mechanical actuator driven by a BLDC motor. This valve can be applied to an engine combustion test after minor change because all development certification test have been performed successfully.

• Journal of Astronomy and Space Sciences
• /
• v.15 no.2
• /
• pp.459-473
• /
• 1998

As the satellite system becomes more complex, the probability of unpredictable failures may be increased due to design inadequacy, experience deficiency, lack of problem recognition. Poor quality control, improper testing, and workmanship fault. Consequently, these problems can lead to the reduction or end of the satellite mission lifetime. This article addresses general satellite failure modes and factors influencing satellite mission life. The mission life factors of LEO sun-synchronous KOMPSAT spacecraft are investigated, in which its mission life is predicted based on these factors. Since the end of mission due to random failures is not predictable, the predictable mission life factors such as power budget, propellant budget, battery charging/discharging cycle, radiation effects payload reliability, single point failure, and redundancy are primarily investigated.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.191-195
• /
• 2006

It is definitely required to control dispersion of the rocket engine performance in order to accomplish the mission of a launch vehicle successfully. A performance dispersion analysis was conducted for a gas generator cycle liquid rocket engine and the required pressure drops were estimated for engine tunning. As a result, the vacuum thrust dispersion of the engine was from +9.1% to -8.7% and the mixture ratio deviated from +9.7% to -9.6% from the nominal value due to the errors of components and the engine inlet condition of propellants. The required pressure drop in the LOx line to the combustor is higher than in the fuel line for same mixture ratio change.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.195-203
• /
• 2003

Spray and Mixing characteristics of the unlike impinging triplet injectors (F-O-F, O-F-O) were investigated with the variation of the momentum ratio of oxidizer to fuel. The spray pattern was measured using a backlit stroboscopic photography technique, and mixing efficiency was measured using a mechanical patternator. Kerosene/water were used as a propellant simulant. From the experimental results, it is found that a O-F-O type injector has a good atomization. And as the momentum ratio increases, the mixing efficiency decreases rapidly.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.255-258
• /
• 2002

Liquid rocket engines using liquefied natural gas (LNG) or methane as a fuel is known to have several good characteristics, such as high specific impulse compared to other hydrocarbon fuels, environment-friendly exhaust gas, low production cost, and re-usability with low soot generation in the cooling channel. In this study, experimental combustion chambers capable of using LNC and $CH_{4}$ are being researched through experimental firing tests, and within easy range of eyes' inspection, there are the periodical existence of soot or discoloration in the chamber wall surface. This result means that mixture ratio of oxidizer and fuel fluctuates periodically between outer-row injectors in the mixing head in the circumferential direction. Therefore, based on this phenomenon, the variation of mixture ratio near the chamber wall caused by the spill pattern of a shear coaxial injector was analyzed quantitatively and the thermal heat flux Into the cooling channel is modified. Then, the calculated and modified results are compared with the measured ones.

• 한국연소학회:학술대회논문집
• /
• 2002.11a
• /
• pp.237-240
• /
• 2002

Micro catalytic reactors are alternative propulsion device that can be used on a nano satellite. When used with a monopropellant, $H_2O_2$, a micro catalytic reactor needs only one supply system as the monopropellant reacts spontaneously on contact with catalyst and releases heat without external ignition, while separate supply lines for fuel and oxidizer are needed for a bipropellant rocket engine. Additionally, $H_2O_2$ is in liquid phase at room temperature, eliminating the burden of storage for gaseous fuel and carburetion of liquid fuel. In order to design a micro catalytic reactor, an appropriate catalyst material must be selected. Considering the safety concern in handling the monopropellants and reaction performance of catalyst, we selected hydrogen peroxide at volume concentration of 70% and perovskite redox catalyst of lantanium cobaltate doped with strondium. Perovskite catalysts are known to have superior reactivity in reduction-oxidation chemical processes. In particular, lantanium cobaltate has better performance in chemical reactions involving oxygen atom exchange than other perovskite materials. In the present study, a process to prepare perovskite type catalyst, $La_{0.8}Sr_{0.2}CoO_3$, and measurement of its propellant decomposition performance in a test reactor are described.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.23 no.4
• /
• pp.30-35
• /
• 2015

In this paper, a theoretical study of low frequency non acoustic instability, the $L^*$ instability, of a solid rocket motor is investigated. The $L^*$ stability criterion is determined by analysing the $L^*$ stability curves of two very distinct propellants for five different geometrical combustors. The $L^*$ instability of two extreme fuels showed totally different behavior in terms of operating pressure of the combustor. A parametric study on the stability for different chamber volume and different throat area keeping constant $L^*$ is conducted and analyzed. It was found that one of the main parameters, the non-dimensional critical characteristic time, requires an enough margin from the critical $L^*$ stability curve.