• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.6
• /
• pp.101-107
• /
• 2020

In this paper, step-curing, which includes the change of curing temperature on the curing process, was applied to reduce curing day of HTPB/AP based propellant. This study targets the improvement of productivity of HTPB/AP based solid rocket motor. Comparison of mechanical properties of propellant resulted in the change of normal curing condition (60℃, 5 days) to step-curing condition (60℃, 1 day / 65℃, 3 days). Post-cure test was conducted to determine the impact on the shelf life of the solid rocket motor. The aging characteristics of propellants were analyzed by measuring mechanical properties and thermal expansion factor. To step-cured propellant, accelerated aging test was performed for 12 weeks, followed by tensile test. Sm(bar) and Em(%) were higher than 8 bar and 40% each, showing excellent mechanical properties.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.4
• /
• pp.92-97
• /
• 2019

A study was conducted to improve the adhesion of propellant, liner,and insulation. Insulation was shown to be more advantageous in improving the adhesion when a barrier coat was applied compared to a bare insulation layer. It was confirmed that the adhesion strength between the insulation and the propellant improves as the thickness of the liner coating increases. The liner was cured for 24 h. If the liner is cured for a long time, it will adversely affect adhesion. Adhesion is also improved when a bonding agent is applied. As the bonding agent content increases, the adhesion improves. There is a change in the adhesive strength depending on the type of bonding agent used. HX-868 shows slightly more improved adhesion than HX-752.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.91.1-91.1
• /
• 2005

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.7
• /
• pp.717-728
• /
• 2009

In the field of rocket propulsion system hydrogen peroxide has been used as mono-propellant and as the oxidizer of bi-propellants. At the beginning, hydrogen peroxide was used as mono-propellant for thrusters, but later it had been replaced by hydrazine, which has better specific impulse and storability. On the other hand, to drive turbo-pumps, hydrogen peroxide is still being utilized. As the oxidizer of bi-propellants it was used until 1970's and from 1990's hydrogen peroxide once again got back to developer's interest, because one of the recent development purposes of rocket propulsion system is low-cost and ecologically-clean. Until now the storability of hydrogen peroxide has been remarkably improved. The combination of Kerosene/$H_2O_2$ also shows similar accelerating performance to Kerosene/$LO_x$ combination because of higher propellant density and higher O/F ratio, even though the propulsion performance is not as good as the combination of Kerosene/$LO_x$. Moreover, its combustion products are much cleaner than Kerosene/$LO_x$ combination.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.4
• /
• pp.112-120
• /
• 2005

The solid propellants have been most widely used for the military rockets or missiles all over the world and the efforts have been focused on the enhancement of propellant performance up to 1980s. lately in company with the distinguished development in the intelligence and communication technology, the more accurate guidance as well as maneuverability has been required in the military weapon system. To meet the requirements such as a high maneuverability, insensitiveness, or stealth of missile, the researches have been doing to develop the solid propellants which have a quality of ultra-fast burning rate, insensitiveness, low signature or the like.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.3
• /
• pp.47-55
• /
• 2013

Curved duct channel flow characteristics for non-Newtonian gel fluid is investigated. A simulant gel propellant mixed by Water, Carbopol 941 and NaOH solution has been chosen to analyze the gel propellant flow behavior. Rheological data have been measured prior to the flow analysis where water-gel propellant and water-gel propellant with $Al_2O_3$ nano particles are both used. The critical Dean number examined by the numerical simulation in the U-shape duct flow reveals that although water-gel-nano propellants have higher apparent viscosity, the critical Dean number do show no notable difference for both the two gel propellant. It is found that the power-law index may be a dominant parameter in determining the critical Dean number and that the gel with particles addition may be more vulnerable to Dean instability.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.6 no.2
• /
• pp.9-19
• /
• 2003

Nitrogen oxide gases which were produced by spontaneous reaction of nitrocellulose(NC) in the single base propellant accelerate the decomposition of propellant, and result in the reduction of shelf life. The amount of nitrogen oxide was reduced by the addition of 0.3wt% $CaCO_3$ to conventional stabilizer(DPA) and down of the solvent leaching temperature from $64^{\circ}C$ to $56^{\circ}C$, which extended the shelf life of the single base propellant as much as twice compare with commercial propellant. The perforation diameter increase of propellant from 0.64mm to 0.77mm could compensate for the drop of burning rate which was caused the addition of $CaCO_3$.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.2
• /
• pp.32-38
• /
• 2004

A comprehensive understanding is given for the hot-firing test results, which were obtained throughout the verification program of mono-propellant hydrazine rocket engines (thrusters) producing 0.95 lbf (4.2 N) of nominal steady-state thrust at an inlet pressure of 350 psia (2.41 Mpa). A scrutiny for the engine performance is made in terms of thrust and temperature behavior of steady state firing mode at the given propellant injection pressures: Pinj = 400, 250, 100, and 50 psi. The thrust and specific impulse are compared with a reference performance of 1-lbf standard rocket engines and their normalization procedure is introduced. A practical engineering approach to the data measurement and reduction is addressed, too.

• Journal of Aerospace System Engineering
• /
• v.18 no.4
• /
• pp.109-116
• /
• 2024

The validity of the analysis results was confirmed based on the insulation test results, and the vaporization mass generated in the common bulkhead was calculated to evaluate the common bulkhead propellant tank's insulation performance. The analysis results were validated by comparing the transient heat transfer analysis with the insulation test results. A transient heat transfer analysis was subsequently conducted on the common bulkhead propellant tank, considering the internal heat conduction in the propellant tank and natural convection heat transfer due to the outside air. This analysis extracted the heat flux generated in the common bulkhead and quantified the vaporization mass, a key indicator of insulation performance. Consequently, the vaporization mass was calculated at 0.09 kg, below the insulation design standard of 0.12 kg for the common bulkhead propellant tank, confirming it meets the insulation performance standard.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.8
• /
• pp.95-103
• /
• 2006

The compositions, the gas properties in motor chamber and the aluminum oxide (Al2O3) particle size for two kinds of solid propellants with approximately 20% aluminum powder have been investigated. The SEM photographs of $Al_2O_3$ taken from nozzle entrance liner show that the aluminized PCP propellant with 47% volumetric fraction AP/HNIW and bimodal oxidizer 200-5 ${\mu}m$ can offer greater possibility for increasing aluminum agglomeration than the aluminized HTPB propellant with 64% volumetric fraction AP and trimodal oxidizer 400-200-6 ${\mu}m$. The nozzle entrance liner of solid rocket motor with the PCP propellant shows greater erosion at 4 circumferential sections in line with grain slots due to the impingement of large particles, but that with the HTPB propellant shows uniform erosion with circumferential angle.