• 한국자동차공학회논문집
• /
• 제10권1호
• /
• pp.187-194
• /
• 2002

It has been reported that cracks in mechanical joints is generally under mixed-mode and there is critical inclined angle at which mode I stress intensity factor becomes maximum. The crack propagates in arbitrary direction and thus the prediction of crack growth path is needed to provide against crack propagation or examine safety. In order to evaluate the fatigue life of cracks in mechanical joints, horizontal crack normal to the applied load and located on minimum cross section is major concern but critical inclined crack must also be considered. In this paper mixed-mode fatigue crack growth test is performed far horizontal crack and critical inclined crack in mechanical joints. Fatigue crack growth path is predicted by maximum tangential stress criterion using stress intensity factor obtained from weight function method, and fatigue crack growth rates of horizontal and inclined crack are compared.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.92-96
• /
• 2007

Microphone array beamforming method has been recognized as an important aeroacoustic research field and become a standard technique in localizing sound sources. This method also used in flight acoustic measurement, and especially, it is very useful when measure sounds inside the wind tunnel. In measuring sound which is inside the wind tunnel by traditional beamforming method, there are some errors caused by airstream. The speed and the propagation path of the sound changes as it travel through the airstream. This makes the error which the position of sound is changed a little bit to the down stream direction. In this paper, validation test has made about the correction equation for this wind effects of previous researches. And beamforming including shear layer correction was performed about a sound source in the anechoic open-jet windtunnel.

• 소음진동
• /
• 제7권1호
• /
• pp.153-159
• /
• 1997

In a stiffened plate reinforced on one of its sides by beam type stiffeners, the asymmetry about the plate mid-plane induces coupling between flexural wave and longitudinal wave. In this research interactions between flexural and longitudinal wave motion are analyzed in a stiffened plate which is reinforced only in one direction. The plate is modelled as a beam to which offset spring-mounted masses are attached at regular intervals. Propagation constants of the coupled waves and corresponding characteristic waves are derived by using periodic structure theory, and a computer code is developed. Also, sample calculations are carried out and the results are discussed.

• 한국연소학회지
• /
• 제4권1호
• /
• pp.39-47
• /
• 1999

A combustion flame visualization system, which is used as an engine diagnostics tool, was developed in order to understand the combustion reaction mechanism in the development stage for S.I. engines. The measurement system consists of an I-CCD camera and a computer-aided image processing system. By using optically accessible engine system, the flame structure was analyzed from the acquired graylevel image and the direction of flame propagation (shape of flame) has been measured to understand combustion phenomena. And combustion radical which involves combustion information were measured. As a result, strong relation between combustion radicals intensity ratio and air excess ratio was found.

• 한국정밀공학회지
• /
• 제19권5호
• /
• pp.43-50
• /
• 2002

Friction welding has many merits such as energy efficiency, simple processing, etc butt difficult to obtain good weld at the welded interface and heat affected zone. To date, the continuum mechanics and fracture mechanics are utilized to analyse stresses at the interface and propagation of cracks. In this study. STS304 and SM15C are selected because they can be differentiated distinctively from metallic point of view and crack can be observed easily. It is ovserved during friction welding that STS304, rotary part is hatter than SH15C, fixed part. The last fracture occurs around the center because the surface of fatigue fracture has smooth regions, due to the separation phenomenon in plastic flows layers and striation dimple pattern.

• 한국군사과학기술학회지
• /
• 제4권1호
• /
• pp.177-187
• /
• 2001

It is important to test and evaluate the variation degree of ship-mounted antenna radiated power with respect to all directions in order to use more effectively antennas that installed on naval ships. The naval ship has various sensors for navigation, communication and electronic warfare, etc. And the performance of these sensors extremely depends on the various characteristics of antenna system to transmit and receive electromagnetic wave. The radiated power pattern of the antenna differs from all aspect angles of the ship because of complex superstructures. It is important to know the weak point(direction) of antenna radiation for appropriate operation. Therefore, the ARP(Antenna Radiation Pattern) of shipboard antennas is measured for the all aspect angles. The results of ARP measurement are utilized as reference for antenna arrangement of newly-built same class warship. This study also describes the development results for the ARP measurement technique, software design and test procedures to measure the radiation pattern of communication equipment antennas using the fixed test site.

• 동력기계공학회지
• /
• 제7권2호
• /
• pp.73-79
• /
• 2003

The present study was aimed at analysing the damage of a used gas turbine bucket after 39,500h of total service. Microstructures and cracks of service-induced bucket were observed. The crack might have initiated from the coating in the bucket surface by thermal fatigue and propagated into the GTD111 base metal. Maximum depth of penetration was 2.7 mm(full penetration) at the leading edge. Crack contains a lot of Cr-,Ti-,Al-oxide which will prohibit filling and wetting of insert metal. Depth and propagation direction of crack were accorded with centrifugal force and temperature distribution in turbine bucket. Present result will provide basic data for repair bonding process.

• Journal of Photoscience
• /
• 제10권1호
• /
• pp.157-164
• /
• 2003

Light exerts two primary roles in plant growth and development. Plants acquire all biochemical energy required for growth and propagation solely from light energy via photosynthesis. In addition, light serves as a medium through which plants recognize environmental fluctuations, such as photoperiod and presence of neighboring animals and plants. Plants therefore constantly monitor the direction, intensity, duration, and wavelength of environmental light and integrate these light signals into the intrinsic regulatory programs to achieve an optimized growth in a given light condition. Although light regulates all aspects of plant growth and developmental aspects, the molecular mechanisms and signaling cascades involved have not been well established until recently. However, recent advances in genetic tools and plant transformation techniques greatly facilitated the elucidation of molecular events in plant photomorphogenesis. This mini-review summarizes the gist of recent findings in deetiolation and suppression of shade avoidance response as classic examples of the phytochrome-mediated photomorphogenesis.

• 소음진동
• /
• 제6권5호
• /
• pp.617-624
• /
• 1996

Finite Element Method(FEM) is one of the most popularly used method in analyzing the dynamic behaviors of structures. But unless the number of finite elements is large enough, the results from FEM are somewhat different form exact analytical solutions, especially at high frequency range. On the other hand, as the Spectral Element Method(SEM) deals directly with the governing equations of structures, the results from this method cannot but be exact regardless of any frequency range. However, despite two dimensional structures are more general, the SEM has been applied only to the analysis of one dimensional structures so far. In this paper, therefore, new methodologies are introduced to analyze the two dimensional plate structure using SEM. The results from this new method are compared with the exact analytical solutions by letting the two dimensional plate structure be one dimensional and showed the dynamic responses of two dimensional plate by including various waves propagated into x-direction.

• 한국안전학회지
• /
• 제13권4호
• /
• pp.113-120
• /
• 1998

Fatigue crack growth rates(i.e. crack initiation and crack growth of short and long crack) are investigated using commercial plates of high strength Al alloy 7075-T651 for the transverse-longitudinal(T-L) direction in air, water and sea water. Also, the evaluation direct current potential drop(D.C.P.D) method and the fractographical analysis by SEM are carried out. Near threshold region, short crack growth rates were much faster than those of comparable long cracks, and these short crack growth rates actually decrease with increasing crack growth and eventually merge with long crack data. Fatigue crack propagation rates in aggressive media(i.e. sea water) increase noticeably over three times those in air. One of the most significant characters in this phenomenon as a corrosion-fatigue causes an acceleration in crack growth rates. Sea water environment, particularly Cl$^{[-10]}$ solution brings the most detrimental effects to aluminum alloy. The result of fractographical morphology in air, water and sea water by SEM shows obvious dimpled rupture and typical striation in air, but transgranular fracture surface in water and sea water.