• 조명전기설비학회논문지
• /
• 제21권9호
• /
• pp.39-46
• /
• 2007

This paper presents a programmable single-phase ac power source that provides a sinusoidal output voltage with an adjustable output amplitude and frequency over a wide range as well as an arbitrary waveform. The ac power source under consideration have a linear power amplifier. The desired output values can be programmed with a personal computer. The power source operates at 220[V]/60[Hz] mains and the output voltage is isolated from the input circuit. The system consists mainly of a power converter to generate and amplify the waveform signal, a controller to control the desired output signal and measure the output parameters, and a control program to set the desired output and display the values. The prototype ac power source was constructed and tested with the results demonstrating a good performance.

• Journal of electromagnetic engineering and science
• /
• 제16권4호
• /
• pp.225-228
• /
• 2016

KRISS-V, a V-band millimeter-wave source module for a primary RF power standard and calibration system developed by the Korea Research Institute of Standards and Science is here presented. The output power of KRISS-V is several times higher than that of commercial amplifier/multiplier chains and is highly stable (the standard deviations of output power are less than 0.01% in the worst case). The spectral purity of KRISS-V is high enough to consider it a single-tone signal generator. We also added programmable attenuation capability to KRISS-V for remote power control. Moreover, the in-house source module is cost-effective and adaptable to various measurement schemes. The structure of the model as well as detailed component information are introduced so that it can be reproduced.

• Journal of Power Electronics
• /
• 제17권1호
• /
• pp.172-180
• /
• 2017

The repetitive control (RC) strategy is widely used in AC power systems because of its high performance in tracking period signal and suppressing steady-state error. However, the dynamic response of RC is determined by the fundamental period delay $T_0$ existing in the internal model. In the current study, a ($nk{\pm}i$)-order harmonic RC structure is proposed to improve dynamic performance. The proposed structure has less data memory and can improve the tracking speed by n/2 times. $T_0$ proves the effectiveness of the ($nk{\pm}i$)-order RC strategy. The simulation and experiments of ($6k{\pm}1$)-order and ($4k{\pm}1$)-order RC strategy used in the voltage source inverter is conducted in this study to control the harmonic current source, which shows the validity and advantages of the proposed structure.

• Journal of Power Electronics
• /
• 제16권2호
• /
• pp.553-563
• /
• 2016

This paper presents a digital hardware implementation of a real-time simulator for a multiphase drive using a field-programmable gate array (FPGA) device. The simulator was developed with a modular and hierarchical design using very high-speed integrated circuit hardware description language (VHDL). Hence, this simulator is flexible and portable. A state-space representation model suitable for FPGA implementations was proposed for a dual three-phase induction machine (DTPIM). The simulator also models a two-level 12-pulse insulated-gate bipolar transistor (IGBT)-based voltage-source converter (VSC), a pulse-width modulation scheme, and a measurement system. Real-time simulation outputs (stator currents and rotor speed) were validated under steady-state and transient conditions using as reference an experimental test bench based on a DTPIM with 15 kW-rated power. The accuracy of the proposed digital hardware implementation was evaluated according to the simulation and experimental results. Finally, statistical performance parameters were provided to analyze the efficiency of the proposed DTPIM hardware implementation method.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.274-277
• /
• 1999

The paper describes a implementation of space vector pulse-width modulation (SVPWM) voltage source inverter using Field Programmable Gate Array(FPGA) for a induction motor control system. The implemented chip is included logic circuits for SVPWM, dead time compensation and speed detection using Quick Logic, QL16X24B. The maximum operating frequency and delay time can be set to 110MHz and 6 nsec. The designed FPGA for SVPWM can be incorporated with a digital signal processing to provide a simple and effective solution for high performance voltage source inverter drives. Simulation and Implementation results are shown to verify the usefulness of FPGA as a Application Specific Integrated Circuit(ASIC) in power electronics applications

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권8호
• /
• pp.1000-1003
• /
• 2014

There are 70 vertical and 70 horizontal correctors for Pohang Light Source. Until mid of 2000, power supplies for these correctors were based on 1990's technology, so the global orbit feedback system was not possible with poor 12 bit resolution. A new task force team was assembled to develop new power supplies with BESSY type DAC cards. After the project, two vertical correctors in each lattice were connected with new power supplies, and the global orbit feedback was available within the accuracy of 5 microns. However, this replacement was not enough to satisfy the beam stability requirement of 2 microns for PLS. We have launched another power supply design based on all digital technology. This attempt was completed within a year, and 80 units were assembled in house. Currently, the global orbit feedback system is running successfully with new digital power supplies and the compensation of chamber motion due to the thermal load by using digital displacement transducers attached on each BPMs.

• Journal of Power Electronics
• /
• 제14권4호
• /
• pp.733-741
• /
• 2014

The integration of photovoltaic (PV) energy sources into DC grid has gained considerable attention because of its enhanced conversion efficiency with reduced number of power conversion stages. During the integration process, a local control unit is normally included with every power conversion stage of the PV source to accomplish the process of maximum power point tracking. A centralized monitoring and supervisory control unit is required for monitoring, power management, and protection of the entire system. Therefore, we propose a field-programmable gate array (FPGA) based centralized control unit that integrates all local controllers with the centralized monitoring unit. The main focus of this study is on the process of integrating many local control units into a single central unit. In this paper, we present design and optimization procedures for the hardware implementation of FPGA architecture. Furthermore, we propose a transient analysis and control design methodology with consideration of the nonlinear characteristics of the PV source. Hardware experiment results verify the efficiency of the central control unit and controller design.

• 한국전자파학회논문지
• /
• 제28권9호
• /
• pp.698-706
• /
• 2017

디지털 제어 시스템에서 주로 사용되는 설비인 PLC(Programmable Logic Controller)와 통신선로에 대한 HPEM(High Power Electromagnetic) 펄스의 노출 위험이 최근 증가되고 있다. 본 연구에서는 서로 다른 주파수 대역을 가지는 HPEM 발생장치를 이용하여 분리된 독립 객체로써 전자 장치의 HPEM에 대한 취약성을 평가하였다. 전자장치가 어떠한 영향을 받는지 상황별로 나누어 비교하였고, HPEM에 노출된 피 시험 기기의 취약성을 분석하였다. 피 시험 기기는 특정 이상의 HPEM에 노출되면, 제어 장치의 전압 및 통신 파형에 왜곡된 특성을 보였으며, UTP(Unshielded Twisted Pair) 케이블에 연결된 장치는 유도전압에 의해 작동 불량을 나타났다. 그러나 FTP(Foiled Twisted Pair) 케이블에 연결된 장치인 경우에는 HPEM 노출로부터 효율적으로 보호되었다. 따라서 현재 전력설비 및 산업현장에서 이용되고 있는 디지털 제어시스템에 대한 HPEM 노출 취약성과 보호대책의 필요성을 입증하였다.

• KIEE International Transactions on Power Engineering
• /
• 제5A권3호
• /
• pp.214-220
• /
• 2005

In order to improve energy efficiency and solve power disturbances, power components measurement for both the supply and demand side of a power system must be implemented before appropriate action on the power problems can be taken. This paper presents a DSP (Digital Signal Processor)-based multi-channel (voltage 8-channel and current 10-channel) power measurement system that can simultaneously measure and analyze power components for both supply and demand. Voltage 8-channel and current 10-channel measurement is made through voltage and current sensors connected to the developed system, and power components such as reactive power, power factor and harmonics are calculated and measured by the DSP. The measured data are stored in a personal computer (PC) and a commercial program is then used for measurement data analysis and display. After voltage and current measurement accuracy revision using YOKOGAWA 2558, the developed system was tested using a programmable ac power source. The test results showed the accuracy of the developed system to be about 0.3 percent. Also, a simultaneous measurement field test of the developed system was implemented by application to the supply and demand side of the three-phase power system.

• 한국산업융합학회 논문집
• /
• 제2권2호
• /
• pp.103-108
• /
• 1999

The paper describes a implementation of space vector pulse-width modulation voltage source inverter and interfacing of DSP using field programmable gate array(FPGA) for a induction motor vector control system. The implemented chip is included logic circuits for SVPWM, dead time compensation and speed detection using Quick Logic, QLl6X24B. The maximum operating frequency and delay time can be set to 110MHz and 6 nsec. The designed Application Specific Integrated Circuit(ASIC) for SVPWM can be incorporated with a digital signal processing to provide a simple and effective solution for high performance induction motor drives with a voltage source inverter. Simulation and implementation results are shown to verify the usefulness of ASIC in a motor drive system and power electronics applications.