• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05a
• /
• pp.127-132
• /
• 2002

Electricity living body formation operation appliance is using most imports until present. And, because electricity living body formation operation appliance is too expensive, it becomes burden to buy in small scale hospital. Also, problem that economical damage by income is added follows. Therefore, this treatise developed electricity living body formation operation appliance by home production. Ultra high frequency eruption circuit used LC circuit. and output frequency is possible to 8 [MHz], and output voltage amplified maximum 800 [V]. This operation appliance could display size of fixed current. This developed product could microscopic operation fewer than 1 [mm]. This development technology is considered by do metallic surface heat treatment, melting, welding, induction heating device and that can apply to domestic animals surgical operation and so on.

• Journal of the Korean Society of Safety
• /
• v.23 no.6
• /
• pp.1-6
• /
• 2008

Machine operator and quality are affected by chip during cutting process to product machine parts. This paper presents a study of the influence of cutting conditions on the surface roughness obtained by turning using Taguchi method for safety of turning operator. In the machining of titanium alloy, high cutting temperature and strong chemical affinity between the tool and the work material are generated because of its low thermal conductivity and chemical reactivity. Therefore titanium alloys are known as difficult-to materials. An orthogonal array, the signal-to-noise ratio, the analysis of variance are employed to investigate the cutting characteristics of implant material bars using tungsten carbide cutting tools of throwaway type. Also Experimental results by orthogonal array are compared with optimal condition to evaluate advanced reliability. Required simulations and experiments are performed, and the results are investigated.

• Transactions of Materials Processing
• /
• v.3 no.3
• /
• pp.359-374
• /
• 1994

Process sequence design in sheet metal forming process by the finite element method is investigated. The forming of sheet metal into a washing machine container is used to demonstrate the design of an improved process sequence which has fewer operations. The design procedure makes extensive use of the finite element method which has simulation capabilities of elastic-plastic modeling. A one-stage process to make an initial blank to the final product is simulated to obtain information on metal flow requirements. Loading simulation for a conventional method is also performed to evaluate the design criteria which are uniform thickness distribution around the finished part and maximum punch load within limit of available press capacity. The newly designed sequence has two forming operations and can achieve net-shape manufacturing, while the conventional process sequence has three forming operations. This specific case conventional process sequence has three forming operations. This specific case can be considered for application of the method and for development of the sequence design methodology in general.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.5
• /
• pp.49-55
• /
• 2002

A new method is proposed for the on-line measurement of the fiber orientation of sheet materials. The measurement of fiber orientation is very important in manufacturing paper sheets, non-woven fabrics, and glass sheets, because fiber orientation strongly affects product properties represented by, for example, dimensional stability of paper. A method developed in this research utilizes anisotropy of dielectric constants of sheet materials as a key characteristic to determine the fiber orientation. The new on-line sensor, consisting of 5 microwave dielectric resonators set in different directions, was designed to detect the fiber orientation while paper is running with high speed on a paper machine. This sensor can determine the direction and the degree of fiber orientation from the measured direction of the maximal dielectric constant and its variation, respectively. The fundamental performance of this system was examined by the static measurement of printing grade paper, which gave a satisfactory result. Then, the dynamic measurements were done at a speed of 1,000 m/min by using a high-speed test-coating machine.

• Journal of the Korea Society of Computer and Information
• /
• v.13 no.1
• /
• pp.261-272
• /
• 2008

The primary research objects of this study is to evaluate an importance of supplier selection factors as an index according the level of product standardization and to present the evaluation model for supplier selection. For this purpose, this study adopts the AHP method to calculate the importance of supplier selection factors. In this study 16 factors which affect on the supplier selection decision making are classified into three factors-product supply related factor, product related factor, management ability related factor. Results also indicate that standardized products are much more dealt by means of on-line compare to customized products. It means the buyer opportunities is potentially an increase in the amount of current supplier re-evaluation, which may lead to new suppliers being considered more often.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.7
• /
• pp.1737-1742
• /
• 2015

In the industrial field for product inspection needs not only on the surface of the product but also the internal components defect inspection. Generally, optical inspection is mainly used for item inspection from production process. However, this is only to check defect of surface it is difficult to perform inspection of goods internal. To overcome these limitations, Instead of optical device by using the portable X- ray DR image acquisition device system developed to obtain an image in real time at the same time and determine product defects. After obtaining the X- ray image, the inspection product within error range is passed after machine image processing. Also, the results and numbers are stored by users.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1587-1590
• /
• 2005

A rigid-plastic finite element analysis for the die forging process of a socket ball joint, which is used in the transportation system, was carried out. And also with the results, the elastic stress analysis for the forging die was performed in order to get basic data for the die life prediction. The die fatigue life prediction was simulated using Goodman's and Gerber's equation. The prediction technique for the fatigue life of a forged product, the socket ball joint, using DEFORM-3D is presented and the results are commented upon. Archard's wear model was used for the wear simulation and then the wear simulation and then the wear quantity was quantity was evaluated using volume. In order to prove the wear simulation results to be reliable, wear quantity of the real forging die set in used a forging factory was measured using a 3-dimensional measurement apparatus. The simulation results were relatively in good agreement with the experimental measurements.

• Transactions of Materials Processing
• /
• v.11 no.3
• /
• pp.262-268
• /
• 2002

The bending process for the rectangular and circular curled tube can be developed by the hot metal extrusion machine with the multiple punches moving in the different velocity. The bending phenomenon has been known to be occurred by the different of velocity at the die exit. The difference of velocity at the die exit section can be obtained by the different velocity of billets through the multi-hole container and by the cohesion of billet Inside the porthole die chamber. The bending phenomenon can be controlled by the two variables, the one of them is the difference of velocity at the die edit section by the different velocity of billets through the multi-hole container The other is the difference by the different hole diameter The results of the experiment show that the rectangular curved tube can be formed by the extrusion process, that the curvature of the curved product can be controlled by the velocity of punch and the diameter of container hole, that the defects such as the distortion of section and the thickness change of the wall of tube and the folding and wrinkling of thin tube did not happen after the extra-bending processing by the extrusion bending machine.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.11
• /
• pp.134-141
• /
• 2003

An industrial product is designed and fabricated, followed by the inspection process in order to check whether it is dimensionally tolerable or not. The machining process produces a part such as a mold or die, in which the three-dimensional coordinate might be measured by a CMM (Coordinate Measuring Machine) for assessment of its dimension. It is not ignorable, however, that a CMM measurement requires a lot of operating time and cost, which has led to many studies on the OMM system. The OMM system can be categorized into contact and non-contact types, and each of which has its own strengths and weaknesses. Non-contacting types generally utilize structured lights, sounds or magnetic fields. Though they show rather poor performance in positional accuracy, the measuring speed is faster than the contacting probes. This paper presents the development of an OMM system based on a non-contacting laser displacement sensing apparatus and CAD model. The system is composed of software modules of center-aligning and measuring, which has been operated and verified on a NC machining center on a shop floor.

• Proceedings of the KIEE Conference
• /
• 2007.11c
• /
• pp.112-116
• /
• 2007

If any of the set parameters such as the environment temperature, mold temperature are not maintained at a consistent level, the fail rate of injection molding products is increased. The price of the injection molding machine is very high, so in order to maximize the utilization of the machine that is required the production of a number of different products with minimum fail rate using a single machine. To prevent the defect products by an inspection process with perfect quality is very important to minimizing production of defect products in the molding process. Vision inspection systems are widely utilized in various manufacturing industries for quality assurance purposes. The vision inspection system consists of CCD camera and lighting system to capture the image of the subject of inspection, an image comparison algorithm using to determine the pass/fail of the products, and mechanical devices for the operation of the whole system. This research focuses on the development of the vision inspection system to process the inspection of an automobile parts. We developed a mechanical devices for the inspection of the injection molding products and an image comparison algorithm to determine the pass/fail result of the inspection based on the molding image and the accepted product image.