• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.2 no.3
• /
• pp.175-180
• /
• 2004

In order to vitrify the combustible dry active waste (DAW) generated from Korean Nuclear Power Plants, a glass formulation development based on waste composition was performed. A borosilicate glass, DG-2, was formulated to vitrify the DAW in an induction cold crucible melter (CCM). The processability, product performance, and volume reduction effect of the candidate glass were evaluated using a computer code and were measured experimentally in the laboratory and CCM. The glass viscosity and electrical conductivity as the process parameters were in the desired ranges. Start-up and maintaining glass melt of the candidate glass were favorable in the CCM. The product of the glass product such as chemical durability, phase stability, and density was satisfactory. The vitrification process using the candidate glass was also evaluated assuming that it was operated as economically as possible.

• Polymer(Korea)
• /
• v.30 no.6
• /
• pp.532-537
• /
• 2006

In order to successfully meet the environmental and recycling problems, natural polymer and their derivatives are recognized as a promising biodegradable material. In this study, the biodegradable composites of cellulose diacetate and starch were prepared, and their physical and thermal properties were investigated. For the melting processing, triacetine was added as a plasticizer into the composites. The processability of cellulose diacetate was further enhanced by increasing the amount of starch in the composites. The tensile stress and Young's modulus were decreased and elongation was increased with increasing the amount of starch in them. A $T_g$ value was decreased with increasing the amount of starch in the composites. Also, the morphology of the composites were observed with the SEM.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1560-1562
• /
• 2000

The paper reports on a study of the influence of the silicone oils on the tracking and erosion resistance and hydrophobicity of SIR. Two silicone oils(A, B) having different chemical structure were selected in consideration of goof hydrophobicity and processability. Tracking and erosion resistance of SIR was investigated by the rotating wheel dip test (RWDT). In this test tracking and erosion areas due to glow and partial arc discharges cause an increase in the leakage current with an increase in time. Leakage current of SIR was decreased with increasing ratio of oil A/B. SIR was exposed to corona discharges in air and the specimens were analyzed with contact angle. It was observed that the contact angle of SIR was increased gradually in time. The recovery of hydrophobicity was increased with increasing ratio of oil A/B.

• Corrosion Science and Technology
• /
• v.15 no.6
• /
• pp.314-319
• /
• 2016

Reduced activation ferritic-martensitic steels (RAFM) are envisaged in future fusion technology as structural material which will be in direct contact with a flowing liquid lead-lithium melt, serving as breeder material. Aluminium-based coatings had proven their ability to protect the structural material from corrosion attack in flowing Pb-15.7Li and to reduce tritium permeation into the coolant, significantly. Coming from scales produced by hot dipping aluminization (HDA), the development of electrochemical-based processes to produce well-defined aluminium-based coatings on RAFM steels gained increased attention in research during the last years. Two different electrochemical processes are described in this paper: The first one, referred to as ECA, is based on the electrodeposition of aluminium from volatile, metal-organic electrolytes. The other process called ECX is based on ionic liquids. All three processes exhibit specific characteristics, for example in the field of processability, control of coating thicknesses (low activation criteria) and heat treatment behavior. The aim of this article is to compare these different coating processes critically, whereby the focus is on the comparison of ECA and ECX processes. New results for ECX will be presented and occurring development needs for the future will be discussed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.6
• /
• pp.109-116
• /
• 2017

In this study, the optimization of the overall dimensions of an automobile bumper was investigated through CAE and experiment using the Six Sigma method and design of experiment (DOE) method, respectively. Injection pressure, injection speed, injection time, cooling time, holding time, injection temperature, and holding pressure were selected as the vital parameters affecting the overall width of product through analysis of trivial many using CAE. The optimal values were determined using the DOE method, and we analyzed the improvement by applying the optimal conditions to the production process. As a result, the mean value of the overall width was close to the target value, with a deviation of 0.05mm, and the processability and I-MR control were remarkably improved. Finally, the dimension pass rate of the product improved by 20%.

• Elastomers and Composites
• /
• v.50 no.3
• /
• pp.184-188
• /
• 2015

There is a need for light weight and high stiffness characteristics in the building structure as well as aircraft and cars. So fiber reinforced plastic with the addition of reinforcing agent such as glass fiber, carbon fiber, aramid fiber is utilized in this regard. In this study, mechanical strength, flow property and part shrinkage of glass fiber and carbon fiber reinforced PA6 were examined according to reinforcement content such as 10%, 20%, and 30%, and reinforcement type. The mechanical property was measured by a tensile test with specimen fabricated by injection molding and the flow property was measured by spiral test. In addition, we measured the part shrinkage of fiber reinforced PA6 that affects part quality. As glass fiber content increases, mechanical property increased by 75.4 to 182%, and flow property decreased by 18.9 to 39.5%. And part shrinkage decreased by 52.9 to 60.8% in the flow direction, and decreased by 48.2 to 58.1% in the perpendicular to the flow direction. As carbon fiber content increases, mechanical property increased by 180 to 276%, flow property decreased by 26.8 to 42.8%, and part shrinkage decreased by 65.0 to 71.8% and 69.5 to 72.7% in the flow direction and the direction perpendicular to the flow respectively.

• Elastomers and Composites
• /
• v.50 no.3
• /
• pp.196-204
• /
• 2015

Crosslink density of a rubber vulcanizate determines the chemical and physical properties, while bound rubber is an important factor to estimate reinforcement of a filled rubber compound. Extender oil is added to a raw rubber with very high molecular weight for improving processability of a rubber composite. Influence of extender oil on crosslink density, bound rubber formation, and physical properties of solution styrene-butadiene rubber (SSBR) composites with differing microstructures was investigated. Crosslink densities of non-oil-extended SSBR (NO-SSBR) vulcanizates were higher than those of oil-extended SSBR (OE-SSBR) ones. Bound rubber contents of NO-SSBR compounds were also greater than those of OE-SSBR ones. The experimental results could be explained by interfering of extender oil. The OE-SSBR vulcanizates had low modulus but long elongation at break, whereas the NO-SSBR ones had high modulus but short elongation at break. It was found that the crosslink densities affected the physical properties more than the bound rubber contents. The moduli increased with increase in the crosslink density irrespective of extender oil, while the elongation at break decreased. Each variation of the tensile strengths of NO-SSBR and OE-SSBR vulcanizates with the crosslink density showed a decreasing trend. Tear strength of the OE-SSBR vulcanizate increased with increase in the crosslink density, whereas variation of the tear strength of NO-SSBR vulcanizate with the crosslink density showed a weak decreasing trend.

• Journal of Adhesion and Interface
• /
• v.21 no.1
• /
• pp.14-19
• /
• 2020

In this study, we synthesized a self-photocuring intermediate(SPI) by Michael addition reaction and synthesized polyurethane acrylate oligomer. Analysis and physical properties of the synthesized SPI and polyurethane acrylate oligomer were confirmed by FT-IR, NMR and UTM. As the content of the SPI increased, the tensile strength increased and the elongation decreased. In addition, since the film was hydrophobic, the surface energy tended to decrease. When the content of the SPI was 40 wt%, adhesion, processability, and pencil hardness were excellent, and solvent resistance was excellent overall.

• Elastomers and Composites
• /
• v.55 no.3
• /
• pp.184-190
• /
• 2020

In the wet master batch process, process oil is used to improve the workability of silica-SBR. The process oil expands the polymer and provides lubrication to soften the stiff rubber chain. However, addition of excess process oil can interfere in the crosslinking reaction between rubber molecules and reduce the crosslinking density of silica-SBR. Controlling the amount of process oil is an important aspect for properly controlling the workability and crosslinking density of silica-SBR. In this study, silica-SBR was prepared by adjusting the amount of process oil to confirm its effect on silicaSBR. Vulcanization characteristics of silica-SBR were examined using a moving die rheometer. Dynamic viscoelasticity was measured using a dynamic mechanical thermal analyzer, and the mechanical properties were investigated using the universal testing machine according to ASTM D412. As a result, all silica-SBR compounds with 10 to 40 phr of process oil have effects of improving the processability and the silica dispersibility. Also, the optimum condition was determined when 10 phr of processed oil was added because the abrasion resistance was improved 65% compared to that at 40 phr.

• Korean Journal of Materials Research
• /
• v.27 no.6
• /
• pp.307-311
• /
• 2017

Organometal halide perovskite materials, due to the tunability of their electronic and optical properties by control of composition and structure, have taken a position of significant importance in optoelectronic applications such as photovoltaic and lighting devices. Despite numerous studies on the structure - property relationship, however, practical application of these materials in electronic and optical devices is still limited by their processability during fabrication. Achieving nano-sized perovskite particles embedded in a polymer matrix with high loading density and outstanding photoluminescence performance is challenging. Here, we demonstrate that the careful control of nanoparticle formation and growth in the presence of poly(methyl methacrylate) results in perovskite nanoparticle - polymer nanocomposites with very good dispersion and photoluminescence. Furthermore, this approach is found to prevent further growth of perovskite nanoparticles, and thus results in a more uniform film, which enables fabrication using the perovskite nanoparticles.