• The Journal of Natural Sciences
• /
• v.8 no.1
• /
• pp.61-69
• /
• 1995

It is hard to synthesize pure $BaTiO_3$ from $BaCO_3$ and $TiO_2$ in solid reaction for the activity of BaO and secondary phase. For this reason, the wet chemical techniques have been studied. Starting material which was used in these methods were expensive and the properties of powder which was synthesized in same defined. So, some process have been studying again to improve soild reaction method. This study which was one of those was to defin the forming mechanism of $Ba_2TiO_4$ and to control some condition of $Ba_2TiO_4$. The synthesis temperature of $BaTiO_3$ in solid reaction was near $1120^{\circ}C$. The quantity and forming temperature of $Ba_2TiO_4$ could be controlled by atmosphere heat treatment. $Ba_2TiO_4$ was related to expansion in Ba-rich region of $BaTiO_3$. $BaTiO_2O_5$ and $BaTiO_3O_7$ was reason to expand in Ti-rich region. The dielectrics of $CeAIO_3$ which was synthesized and sintered in reduction atmosphere and $BaTiO_3$ system were affected by $CeO_2$ which was formed for the decomposition of $CeAIO_3$ heat treatment in air.

• Geophysics and Geophysical Exploration
• /
• v.22 no.4
• /
• pp.177-185
• /
• 2019

Ground roll is a surface wave which is usually observed in the land seismic data. It is one of the typical coherent noise. During the reflection data processing, ground roll is removed because it is considered as noise. This removal process often causes the loss of reflection signals if the ground roll overlaps reflection signals. In this study, we look over Karhunen-Loeve Transform (KLT) and analyze its effects to suppress the ground roll appropriately while reducing the reflection loss. Numerical tests in homogeneous elastic media show that the ground roll has been properly rejected. However, the field data application reveals that there is no significant suppression of ground roll when compared to band-pass filtering. This can be considered that it is hard to calculate horizontally aligned gathers in the field data because the ground roll contains a wide range of frequency bands. On the contrary, the result of singular value decomposition (SVD) filtering shows that the ground roll has been significantly reduced. It is thought that the SVD filtering performs better in the ground roll suppression than KLT because it is easy to calculate the horizontally aligned gathers in the SVD filtering.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.3
• /
• pp.137-145
• /
• 2014

We present a design sensitivity analysis(DSA) method for multiscale problems based on bridging scale decomposition. In this paper, we utilize a bridging scale method for the coupled system analysis. Since the analysis of full MD systems requires huge amount of computational costs, a coupled system of MD-level and continuum-level simulation is usually preferred. The information exchange between the MD and continuum levels is taken place at the MD-continuum boundary. In the bridging scale method, a generalized Langevin equation(GLE) is introduced for the reduced MD system and the GLE force using a time history kernel is applied at the boundary atoms in the MD system. Therefore, we can separately analyze the MD and continuum level simulations, which can accelerate the computing process. Once the simulation of coupled problems is successful, the need for the DSA is naturally arising for the optimization of macro-scale design, where the macro scale performance of the system is maximized considering the micro scale effects. The finite difference sensitivity is impractical for the gradient based optimization of large scale problems due to the restriction of computing costs but the analytical sensitivity for the coupled system is always accurate. In this study, we derive the analytical design sensitivity to verify the accuracy and applicability to the design optimization of the coupled system.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.30 no.2
• /
• pp.169-177
• /
• 2017

In this paper, classification of spall and crack faults of gear teeth is studied by applying the ensemble empirical mode decomposition(EEMD) for the gear transmission error(TE). Finite element models of the gears with the two faults are built, and TE is obtained by simulation of the gears under loaded contact. EEMD is applied to the residuals of the TE which are the difference between the normal and faulty signal. From the result, the difference of spall and crack faults are clearly identified by the intrinsic mode functions(IMF). A simple test bed is installed to illustrate the approach, which consists of motor, brake and a pair of spur gears. Two gears are employed to obtain the TE for the normal, spalled, and cracked gears, and the type of the faults are separated by the same EEMD application process. In order to quantify the results, crest factors are applied to each IMF. Characteristics of spall and crack are well represented by the crest factors of the first and the third IMF, which are used as the feature signals. The classification is carried out using the Bayes decision theory using the feature signals acquired through the experiments.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.34 no.3
• /
• pp.173-178
• /
• 2001

This study was performed to know the hypocholesterolemic effect of depolymerized alginate obtained by hydrolysis of alginate through a heating process at $121^{\circ}C$. The changes of total cholesterol, HDL-cholesterol, LDL-cholesterol, triglycerides and phospholipid levels in serum, as well as the atherogenic index were elucidated in rats for 35 days. In order to evaluate single-dose toxicity of HAG-50 in rats via oral routes, induction any mortalities and abnormal signs in clinical finding, body weight, gross findings and histopathological finding, and estimation of $LD_{50}$ were elucidated. Total cholesterol, HDL-cholesterol, LDL-cholesterol, triglycerides and phospholipid levels in the serum significantly decreased and resulted in the decrease of atherogenic index in rats fed diets containing $5\%\;and\;10\%$ HAG-50 (p<0.01). HAG-50 did not induce any mortalities and abnormal signs in clinical findings, body weights, gross findings and histopathological findings in single-dose toxicity test via oral routes of rats, after which it was impossible to estimate $LD_{50}$ values.

• Journal of Korean Society of Forest Science
• /
• v.85 no.4
• /
• pp.656-666
• /
• 1996

Aspen demand has increased recently in the Great Lakes region in the United States. Since aspen has moved into the region in late 1800's, its growing stock has increased so as to change forestry industry of the Lake States. Intensive timber harvesting and biomass removal may cause nutrient depletion, especially on nutrient-poor sites. Forest nutrients and nutrient cycling were investigated in aspen stands of 7-10, 27-33, and 41-42 year-old growing on sandy soils in Minnesota. Nutrients added to the aspen stands by atmospheric deposition and soil weathering were efficiently absorbed and stored in the tree biomass. Aboveground biomass increased from $24.4t{\cdot}ha^{-1}$ at young stands to $139.2t{\cdot}ha^{-1}$ at mature stands. Nutrients accumulated in the tree biomass showed same magnitude of difference. Nutrients added to the site through atmospheric deposition were in the order of Ca, N, K, Mg, and P. Annual litterfall was greater in older stands. However, the amount of nutrients returned by litterfall was not significantly different among stand ages due to the greater nutrient contents in the litterfall of young stands. Litter decomposition and nutrient release rates were greater at young stands than at older stands. Likewise, nutrient availability was higher in young aspen stands and became lower as the stands grew older. Nutrient leaching loss was minimal at all stand ages. Soil N mineralization was greater at young stands than at older stands. Nutrient cycling process was facilitated in young aspen stands with an increased level of available nutrients, Based on the estimations of nutrient balance and nutrient removal by harvesting, Ca was the most critical element which was likely to be depleted if aspen stands are intensively harvested with short rotations.

• Korean Chemical Engineering Research
• /
• v.50 no.3
• /
• pp.567-573
• /
• 2012

Compared with the natural marble, the artificial marble has the advantages of excellent appearance, high degree of finish, even color, fine pressure and wear resistance, bear erosion and weathering, etc. It can be widely used in kitchen countertops, bath vanity tops, table tops, furniture, reception desks, etc. However, large amounts of artificial marble waste such as scraps or dust have been generated from sawing and polishing processes in artificial marble industry. Waste from artificial marble industry is increasing according to demand magnification of luxurious interior material. Artificial marble wastes can be recycled as aluminum oxide used as raw materials in electronic materials, ceramics production, etc., and methyl methacrylate(MMA) which become a raw material of artificial marble by pulverization, pyrolysis and distillation processes. The characteristics of artificial marble wastes was analyzed by using TGA/DSC and element analysis. Crude aluminum oxide was obtained from artificial marble waste by pulverization and thermal decomposition under nitrogen atmosphere. In this work, Box-Behnken design was used to optimize the pyrolysis process. The characteristics of crude aluminum oxide was evaluated by chromaticity analysis, element analysis, and surface area.

• Korean Chemical Engineering Research
• /
• v.56 no.5
• /
• pp.725-731
• /
• 2018

The effects of catalysts addition on the carbonization reaction of biomass have been studied in a thermogravimetric analyzer (TGA). The sample biomasses were Bamboo and Pine. The catalysts tested were K, Zn metal compounds. The carbonization reactions were tested in the nonisothermal condition from the room temperature to $850^{\circ}C$ at a heating rate $1{\sim}10^{\circ}C/min$ on the flowing of $N_2$ purge gases. Also, the effects of catalyst on the torrefaction were tested in the temperature condition of 220, 250, $280^{\circ}C$ at 30 min. Combustion characteristic for the torrefied catalyst biomass were studied in the nonisothermal conditions of $200{\sim}850^{\circ}C$. As the results, the initial decomposition temperatures of the volatile matters ($T_i$) and the temperature of maximum reaction rate ($T_{max}$) were decreased with increasing the catalyst amounts in the sample biomass. The char amounts remained after carbonization at $400^{\circ}C$ increased with the catalyst amounts. Therefore catalysts addition can be decreased the energy for carbonization process and improved the heating value of product char. The catalysts reduced the optimum torrefaction conditions from $250^{\circ}C$ to $220^{\circ}C$. The torrefied catalyst biomass have lower activated energy from 46.5~58.7 kJ/mol to 25.1~27.0 kJ/mol in the nonisothermal combustion reaction.

• Clean Technology
• /
• v.20 no.4
• /
• pp.398-405
• /
• 2014

In the treatment of spent high energetic materials, the issues such as environmental pollution, safety as well as working capacity should be carefully considered and well examined. In this regard, incineration has been recommended as one of the most promising processes for the disposal of such explosives. Due to the fact that high energetic materials encompass various types and their different characteristics, the technology development dealing with various materials is not an easy task. In this study, rigorous modeling and dynamic simulation was carried out to predict dynamic physico-chemical phenomena for research department explosive (RDX). Plug flow reactor was employed to describe the incinerator with 263 elementary reactions and 43 chemical species. Simulation results showed that safe operations can be achieved mainly by controlling the reactor temperature. At 1,200 K, only thermal decomposition (combustion) occurred, whereas increasing temperature to 1,300 K, caused the reaction rates to increase drastically, which led to ignition. The temperature further increased to 3,000 K which was the maximum temperature recorded for the entire process. Case studies for different operating temperatures were also executed and it was concluded that the modeling approach and simulation results will serve as a basis for the effective design and operation of RDX incinerator.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.31 no.2 s.51
• /
• pp.141-146
• /
• 2005

Unstable cosmetic active ingredients could rapidly break down in chemical and photochemical process. Therefore, it has become a very important issue to encapsulate active ingredient for the stabilization. 7-Dehydrocholesterol (7-DHC), a precursor of vitamin $D_3$, has been shown to increase levels of protein and mRNA for heat shock protein in normal human epidermal keratinocytes. However, topical dermal application of 7-DHC is restricted due to its poor solubility and chemical unstability. In this study, 7-DHC was incorporated into nano-emulsion (NE), solid lipid nano-particle (SLN), and chitosan coated solid lipid nano-particle (CASLN), respectively. In order to prepare NE and SLN dispersion, high-pressure homogenization at temperature above the melting point of lipid was used Hydrogenated lecithin and polysorbate 60 were used as stabilizer for NE and SLN. CASLN was prepared by high speed homogenizing after adding chitosan solution to the SLN dispersion and showed positively charged particle properties. Decomposition rate of 7-DHC in NE, SLN and CASLN was studied as a function of time at different temperature. Differential scanning calorimetry (DSC) and X-ray diffraction (XRD) studies were performed to characterize state of lipid modification. It appeared that CASLN is the most effective to stabilize 7-DHC and may be used for a useful topical dermal delivery system.