• 반도체디스플레이기술학회지
• /
• 제20권4호
• /
• pp.177-181
• /
• 2021

Scaffolds protect the sensor in the body. Scaffolds are made of a bioabsorbable polymer. The polymer process is sensitive to humidity. Inside of the 3D printer has been improved to control the humidity. Specimens were produced by injection molding and 3D printer. 3D printed specimens were printed under various humidity conditions. We measured tensile strength of the injection-molded specimen and tensile strength of the 3d printing specimen. We compared tensile strength of the injection-molded specimen and tensile strength of the 3d printing specimen. Tensile strength of the injection-molded specimen is 557 kgf/cm². We confirmed tensile strength of the specimen was highest at 741 kgf/cm² when the humidity was 10 %. We confirmed lower the humidity, higher tensile strength of the polymer product.

• 폴리머
• /
• 제36권2호
• /
• pp.169-176
• /
• 2012

저항형 습도센서의 개발을 위하여 스크린 인쇄방법으로 glass epoxy(GE) 기재 위에 핑거의 수와 그 사이의 간격이 다른 여러 가지 바이트형의 금 전극을 제조하였다. 전극의 기본적인 구조는 핑거 수가 3, 4 및 5를 가지며 간격은 각각 310과 460 ${\mu}m$이다. 전극은 처음에 은 나노 페이스트로 전극 패턴을 인쇄하고 연속적으로 Cu, Ni 및 Au를 무전해 도금을 진행하여 제조하였다. 감습성 고분자 전해질은 [2-(methacryloyloxy)ethyl] dimethyl benzyl ammonium chloride(MDBAC)과 methyl methacrylate(MMA)의 공중합체를 사용하였으며 스크린 인쇄 방법으로 Au 전극/GE 기재 위에 인쇄하였다. 이렇게 제조된 습도 센서의 20-95%RH 영역의 상대습도 대 로그 임피던스 그래프에서 좋은 직선성을 보여주었으며 히스테리시스는 1.5%RH 이하 및 75초의 응답 및 회복 속도를 보여주었다. 전극의 구조는 고분자 저항형 습도센서의 감습특성에 큰 영향을 미치며 전해질 고분자와 전극 사이의 활성화 에너지, 온도의존성, 감도, 직선성 및 히스테리시스와 같은 감습특성 등의 차이를 비교하였고 특히 이온의 이동에 관여하는 활성화 에너지 및 온도 의존성에 큰 영향을 미쳤다.

• 한국인쇄학회지
• /
• 제23권2호
• /
• pp.103-115
• /
• 2005

In off-set printing or coating process, it transfers ink on plate by rolling system. As Ink flows between rolls have an influence on printability of the final products, it needs to be studied scientifically and then control its values. Ink flows between rolls are processed under the effect of diversity factors such as rhelogical properties, printing speed, temperature, humidity etc. Therefore, this study try to approach the real ink transfer mechanism to be concerned about all sorts of variables.

• Bulletin of the Korean Chemical Society
• /
• 제34권9호
• /
• pp.2781-2786
• /
• 2013

We examined the effect of electrode fingers and gaps of coplanar interdigitated electrode (IDE) structures to characterize the ammonium salt-containing polyelectrolyte film of resistance-based humidity sensors. IDEs designed for this purpose were flexible gold electrodes deposited on a polyimide substrate using a printing process because the geometry presents a potential for tunable sensitivity over other electrode designs. The basic design of the sensors consisted of IDEs with a different number of electrode fingers such as 3, 4, and 5 and gap sizes of 310, 360, 410, and $460{\mu}m$. Details of the AC complex impedance characteristics such as the Nyquist plot, Bode plot, and activation energy based on electrode construction were investigated.

• 한국안전학회지
• /
• 제19권3호
• /
• pp.51-56
• /
• 2004

Conductive polymer blends and composites are widely used for different safety application such as electrostatic charge dissipation(ESD), electromagnetic interference(EMI) shielding, electrostatic prevention and safety chemical sensor. In order to prepare a impedance-type humidity sensor that is durable at high humidities and high temperature, electically conductive polymer blends based on diallyldimethylammonium chloride(DADMAC) and epoxy were prepared in this study. The polymer blends type conductive ionomer exhibits reaction each other DADMAC and epoxy in FT-IR and DSC analysis. The blends material was traced by new peak at 1600cm-1 and appeard improvement of thermal resistance by melting point shift. Alumina substrate was deposited a pair of gold electrodes by screen printing. The blend material were spin-coated with a thin film type on the surface of alumina substrate. The polymer bleld type sensor exhibits a linear impedance increasing better than DADMAC coated humidity sensor. Also it shows good sensitivity, low hysteresis and durability against high humidity.

• 한국지역사회생활과학회지
• /
• 제23권3호
• /
• pp.317-328
• /
• 2012

In this study, printing was introduced to the common dip-dyeing method of persimmon juice dyeing so as to develop two different colored persimmon juice dyed fabrics with printings of 'jorangmal' patterns (a national monument) instead of producing a plain textile. Following are the results of a comparative study between the persimmon dyed fabric and undyed fabric, both with printings, in terms of its properties, and hand values. Cotton and rayon were chosen as samples and were compared separately. Firstly, the samples showed differences in terms of clarity and visual sensation depending on the presence of persimmon dye, even if the same pattern and color was used. Secondly, the air permeability of two samples improved after persimmon dyeing even though their thickness increased, and their moisture regain increased as well in all humidity conditions. Thirdly, protectiveness against UV increased in dyed samples, and sweat, sunlight, and compound colorfastness improved in printed dye-fabrics compared to plain dyed ones. Therefore, printing proved to be effective in preventing discoloration. Fourthly, tensile linearity and resilience, bending rigidity, compressive linearity and resilience, and shearing stiffness increased more in the dyed samples compared to undyed ones. However, shearing recovery decreased in both dyed fabrics. Fifthly, the result of its hand value showed that Koshi value increased in all samples than undyed ones, whereas Fukurami, Numeri, and Softosa values decreased. Incorporating printing in persimmon dyeing process could expect creative outcomes not only in today's diverse fashion but in areas of arts or crafts as well.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2010년도 춘계학술발표대회
• /
• pp.19.2-19.2
• /
• 2010

Printed electronics using printing process has broadened in all respects such as electrics (lighting, batteries, solar cells etc) as well as electronics (OLED, LCD, E-paper, transistor etc). Copper is considered to be a promising alternative to silver for printed electronics, due to very high conductivity at a low price. However, Copper is easily oxidized, and its oxide is non-conductive. This is the highest hurdle for making copper inks, since the heat and humidity that occurs during ink making and printing simply accelerates the oxidation process. A variety of chemical treatments including organic capping agents and metallic coating have been used to slow this oxidation. We have established synthetic conditions of copper nanoparticles (CuNPs) which are resistant to oxidation and average diameter of 20 to 50nm. Specific resistivity should be less than $4\;{\mu}{\Omega}{\cdot}cm$ when sintered at lower temperature than $250^{\circ}C$ to be able to apply to conductive patterns of FPCBs using ink-jet printing. Through this study, the parameters to control average diameter of CuNPs were found to be the introduction of additive agent, the feeding rate of reducing agent, and reaction temperature. The CuNPs with various average diameters (58, 40, 26, 20nm) could be synthesized by controlling these parameters. The dispersed solution of CuNPs with an average size of 20 nm was made with nonpolar solvent containing 3 wt% of binder, and then coated onto glass substrate. After sintering the coated substrates at $250^{\circ}C$ for 30 minutes in nitrogen atmosphere, metallic copper film resulted in a specific resistivity of $4.2\;{\mu}{\Omega}{\cdot}cm$.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.597-598
• /
• 2006

In this study, we used the ESD method to prepare the protein microarrays for observation the stem cell responses to pattern size, space and shapes. The ESD method allows a reduction in spot size, high efficiency of substance transfer, and high rate in fabrication as a result of ability to simultaneously deposit thousands of identical spots. Typical electro spraying conditions for the deposition of proteins were a voltage of $3{\sim}5keV$ and the humidity under 30%. The patterns of masks have a variety of shapes, spaces, and hole sizes from 10 um to $300{\mu}m$. Three kinds of proteins(collagen, fibronectin, and vitronectin dissolved in PBS) are deposited in a dry state, preserving the functional activity of proteins. Stem cells were cultured on each protein patterned sample at $37^{\circ}C$ for 1day.

• 한국기계가공학회지
• /
• 제17권3호
• /
• pp.51-58
• /
• 2018

In this paper, the organic material Poly(methyl methacrylate) PMMA is used with inorganic $Al_2O_3$ to fabricate organic-inorganic multilayer barrier thin films. The organic thin films are developed using a roll-to-roll electrohydrodynamic atomization system, whereas the inorganic are grown using a roll-to-roll low-temperature atmospheric pressure atomic layer deposition system. For the first time, these two technologies are used together to develop organic-inorganic multilayer barrier thin films in atmospheric condition. The films are grown under optimized parameters and classified into three classes based on the layer structures, when the total thickness of the barrier is maintained at ~ 160 nm. All classes of barriers show good morphological, optical and chemical properties. The $Al_2O_3$ films with a low average arithmetic roughness of 1.58 nm conceal the non-uniformity and irregularities in PMMA thin films with a roughness of 5.20 nm. All classes of barriers show a notably good optical transmission of ~ 85 %. The hybrid organic-inorganic barriers show water vapor and oxygen permeation in the range of ${\sim}3.2{\times}10^{-2}g/m^2/day$ and $0.015cc/m^2/day$ at $23^{\circ}C$ and 100% relative humidity. It has been confirmed that it can be mass-produced and used as a low-cost barrier thin film in various printing electronic devices.

• 마이크로전자및패키징학회지
• /
• 제14권2호
• /
• pp.59-63
• /
• 2007

간단한 PCB 공정을 기반으로 하여 저가형의 후막 가스 센서 모듈을 제안하고자 한다. 제안된 센서 모듈은 $NO_2/H_2$ 가스 센서와 습도센서, 그리고 히터를 포함한다. $NO_2/H_2$ 가스와 상대 습도 센서들은 각각 $SnO_2$와 $BaTiO_3$ 나노 입자들을 PCB 기판에서의 IDT(interdigital Transducer)에 프린팅 함으로써 제작되었다. 처음에 1% $H_2$ 가스를 센서 쳄버에 공급하고 4분 후 $H_2$가스 공급을 멈추고 공기를 주입시켰으며, 이러한 동작을 반복적으로 수행하였다. 마찬가지로 $NO_2$로 감지하도록 같은 동작을 실행하였다. $H_2$ 가스에 대한 결과는 도전성의 증가로 인하여 0.8V에서 3.5V로 증가함을 볼 수 있었으며, $H_2$ 가스를 주입한후의 반응 시간은 65초였다. $NO_2$ 가스의 경우는 도전성이 감소함으로써 2.7 V의 전압강하가 일어 났으며, 반응시간은 3초였다.