• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.732-737
• /
• 2005

Distal 3D Real Object Duplication System(RODS) consists of 3D Scanner and Solid Freeform Fabrication System(SFFS). It is a device to make three-dimensional objects directly from the drawing or the scanning data. In this research, we developed an office type SFFS based on Three Dimensional Printing Process and a industrial SFFS using Dual Laser. An office type SFFS applied sliding mode control with sliding perturbation observer(SMCSPO) algorithm for control of this system. And we measured process variables about droplet diameter measurement and powder bed formation etc. through experiments. Also, in order to develop more elaborate and speedy system for large objects than existing SLS process, this study applies a new Selective Multi-Laser Sintering(SMLS) process and 3-axis dynamic Focusing Scanner for scanning large area instead of the existing $f\theta$ lens. In this process, the temperature has a great influence on sintering of the polymer. Also the laser parameters are considered like that laser beam power, scan speed, scan spacing. Now, this study is in progress to eveluate the effect of experimental parameters on the sintering process.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.1
• /
• pp.83-90
• /
• 2014

EHD (electro-hydro-dynamics) patterning was performed under atmospheric pressure at room temperature in a single step. The drop diameter smaller than nozzle diameter and applied high viscosity conductive ink in EHD patterning method provide a clear advantage over the piezo and thermal inkjet printing techniques. The micro electrode pattern was printed by continuous EHD patterning method using 3-type control parameters (input voltage, patterning speed, nozzle pressure). High viscosity (1000cps) conductive ink with 75wt% of silver nanoparticles was used. EHD cone type nozzle having an internal diameter of $50{\mu}m$ was used for experimentation. EHD jetting mode by input voltage and applied 1st order linear regression in stable jet mode was analyzed. The stable jet was achieved at the amplitude of 1.4~1.8 kV. $10{\mu}m$ micro electrode pattern was created at optimized parameters (input voltage 1.6kV, patterning speed 25mm/sec and nozzle pressure -2.3kPa).

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1066-1071
• /
• 2005

This paper presents the two lossless auxiliary inductors-assisted voltage source type half bridge (single ended push pull: SEPP) series resonant high frequency inverter for induction heated fixing roller in copy and printing machines. The simple high-frequency inverter treated here can completely achieve stable zero current soft switching (ZCS) commutation for wide its output power regulation ranges and load variations under its constant high frequency pulse density modulation (PDM) scheme. Its transient and steady state operating principle is originally described and discussed for a constant high-frequency PDM control strategy under a stable ZCS operation commutation, together with its output effective power regulation characteristics-based on the high frequency PDM strategy. The experimental operating performances of this voltage source SEPP ZCS-PDM series resonant high frequency inverter using IGBTs are illustrated as compared with computer simulation results and experimental ones. Its power losses analysis and actual efficiency are evaluated and discussed on the basis of simulation and experimental results. The feasible effectiveness of this high frequency inverter appliance implemented here is proved from the practical point of view.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.942-945
• /
• 2003

Nerve gas sensor based on tin oxide was fabricated and its characteristics were examined. Target gas was dimethylmethylphosphonate($C_3H_9O_3P$, DMMP) that is simulant gas of nerve gas. Sensing material was $SnO_2$ added ${\alpha}-Al_2O_3$ with $4{\sim}20wt.%$ and was physically mixed. And then it was deposited by screen printing method on alumina substrate. Sensor device was consisted of sensing electrode with interdigit(IDT) type in front and heater in back side. Total size of device was $7{\times}10{\times}0.6mm^3$. Crystallite size of fabricated $SnO_2$ were characterized by X-ray diffraction(XRD, Rigaku) and morphology of the $SnO_2$ powders was observed by a scanning electron microscope(SEM, Hitachi). Fabricated sensor was measured as flow type and sensor resistance change was monitored real time using LabVIEW program. The best conditions as added $Al_2O_3$ amounts and operating temperature changes were 4wt.% and $300^{\circ}C$ in DMMP 0.5ppm, respectively. The sensitivity was over 75%. Response and recovery times were about 1 and 3 min., respectively. Repetition measurement was very good with ${\pm}3%$ in full scale.

• Journal of the Korean Society of Costume
• /
• v.34
• /
• pp.135-150
• /
• 1997

The purpose of this study was to inves-tigate the economic performance of the textile industry for the Korean traditional clothes. The content of this paper had two pars; The first part was for the macroeconomic aspects such as location production employments and the produc-tion facilities of the textile industries. The second part was for the microeconomic aspects such as business type branding method fabric type R&D efforts sourc-ing and the distributional channel The major results were as follows: 1.) Most textile firms for the korean traditional clothes were located in Gongju for man-made fibers and in Jinju for silk fabrics. 2) The size of the textile industry in terms of the number of business produc-tion amount the number of employee de-creased during 1994 and 1995 due to the decreasing demand. 3) Over the half of the textile firms produced raw fabric products while only 20% of them were involved in additional dyeing and /or printing finish which re-sulted in low value added production 4) The R&D effort of the textile indus-try for the Korean traditional clothes was very low due to the market uncertainty lack of technological knowledge and most of all small size of the firms 5) Most raw materials for the textile in -dustry were imported with high(25%) tariff rates resulting in price increase and thus low competitiveness in the market. 6) The textile producers sole about the 70% of their products to the wholesalers while selling the rest to the retailers di-rectly. This showed the dual structure of the distribution channel in the textile products. These results suggested some implica-tions for the firms the policy makers and the researchers. The firms should develop new and improved products to increase and create consumer demand by intensive R&D efforts. The government policy ma-kers should give financial supports the firms with R&D investment and legal help such as lowing tariff rate for the raw ma-terials. The researchers from the academy could help the textile industry with the advanced technological knowledge and up-date information for the consumer fashion demand.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.4
• /
• pp.325-329
• /
• 2016

In this study, we investigated the feasibility of using printed Indium Tin Oxide (ITO) film as a remote sensor for Hazardous and Noxious Substances (HNS). To improve the quality of the ITO films, binder mixing ratio, Sn concentration in ITO, thermal treatment temperature, and printing process conditions were optimized. We fabricated an electrical resistance-type liquid sensor, and to confirm the sensor operation, the change in resistance in air and seawater was monitored. The change in resistance of the ITO sensor was explained in terms of reduction reaction on the surface. Further, the sensor was controlled by Arduino, and the remote data acquisition was demonstrated.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.9 no.2
• /
• pp.75-84
• /
• 1985

In order to improve dyeing and finishing technology of thin cloth of microfiber(super-fine fiber), the degrees of deep dyeing method, the light fastness, and the washing fastness were investiagted. 1. The thin cloth made of microfiber, $0.15^d\~0.2^d$, was conjugated type and the dyeing degree was lower at 5 to $10\%$ than that of cloth made of common fiber. The cloth of excellent dyeing fastness, light fastness, was developed by increasing the concentration of dye of high quality up to $5\~10\%$. 2. Because refractory rate of microfiber of $0.2^d$ was lower than that of $0.01^d$, the surface refractory rate of $0.2^d$ was lower than that of $0.01^d$ fiber. Therefore the surface of micro-fiber, $0.2^d$, was more rougher than that of $0.01^d$ and it belongs to separate type. 3. The higher degree of dyeing was increased by using dye of microparticle. Also the degree of textile printing was increased by adding urea solution ($20\%$) and glycerine diethylene glycol. 4. Light fastness was very excellent, marked 5 grade. However, washing fastness was 2$\~$3 grade. After dyeing, we could improve to 4 grade, through hot water washing including some organic chlorine solvent. 5. Super microfiber of $0.01^d$ will not be dyed by present dye and dyeing equipment, because right reflection light rate(white light) of fiber surface was too high and the more refraction rate higher the more surface refraction rate will be increased.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.12
• /
• pp.1322-1328
• /
• 2009

This paper presents vibration analysis of maskless exposure module in printed circuit board(PCB) manufacturing system. In order to complete exposure process in PCB, masking type module has been widely used in electronics industries. However, masking process confronts some limitations of application due to higher production cost for masking as well as lower printing resolution. Therefore, maskless exposure module is started to be in the spotlight for flexible production system to meet the needs of fabrication in variable patterns at low cost. Since maskless exposure process adopts direct patterning to PCB, vibration problems become more critical compared to conventional masking type process. Moreover, movements of exposure engine as well as stage generate vibration sources in the system. Thus, it is imperative to analyze the vibration characteristics for the maskless exposure module to improve the quality and accuracy of PCB. In this study, vibration analysis using the finite element analysis is conducted to identify the critical structural parts deteriorating vibration performance. Also, Experimental investigations are conducted by single/dual encoder measurement process under the operating module speed. Measurement points of vibration are selected by three places, which are base of stage, exposure engine and top of stage, to check the effect of vibration from the exposure engine. Comparisons between analysis results and experimental measurement are conducted to confirm the accuracy of analysis results including the developed FE model. Finally, this studies show feasibility of optimal design using the developed FE analysis model.

• Journal of Sensor Science and Technology
• /
• v.5 no.1
• /
• pp.23-29
• /
• 1996

Thick film type gas sensors with parallel Pt heaters were fabricated by screen printing process and investigated sensitivities for methane gas. The TR7905 was selected as Pt paste for heater by characterization the properties of TCRs and thick film microstructures. The average resistance of parallel Pt heaters was $1.8{\Omega}$, and the best TCR obtained was $3685\;ppm/^{\circ}C$. On the top of the Pt heaters, a sensing layer added with Pt and Pd as catalyst paste was screen printed and heat treated. The sensitivity of the sensor was 4.3mV/1000ppm for methane. The power consumption of the sensors was 2.12watts.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1217-1223
• /
• 2003

Nerve gas sensor based on tin oxide was fabricated and its characteristics were examined. Target gas is dimethyl methyl phosphonate(C$_3$ $H_{9}$ $O_3$P, DMMP) that is simulant gas of nerve gas. Sensing materials were Sn $O_2$ added a-Al$_2$ $O_3$ with 0∼20wt.% and were physically mixed each material. They were deposited by screen printing method on alumina substrate. The sensor device was consisted of sensing electrode with interdigit(IDT) type in front and a heater in back side. Total size of device was 7${\times}$10${\times}$0.6㎣. Crystallite size & phase identification and morphology of fabricated Sn $O_2$ powders were analyzed by X-ray diffraction and by a scanning electron microscope, respectively. Fabricated sensor was measured as flow type and resistance change of sensing material was monitored as real time using LabVIEW program. The best sensitivity was 75% at adding 4wt.% $\alpha$-Al$_2$ $O_3$, operating temperature 30$0^{\circ}C$ to DMMP 0.5ppm. Response and recovery time were about 1 and 3min., respectively. Repetition measurement was very good with $\pm$3％ in full scale.TEX>$\pm$3％ in full scale.