• Proceedings of the KIEE Conference
• /
• 2002.04a
• /
• pp.183-185
• /
• 2002

This paper proposes the test method for the testing of a RLC parallel circuit on the electronic circuit board. This method utilizes a guarding circuit and a phase detection circuit. The guarding circuit separates electrically the tested device or circuit from printed circuit board. Phase detector estimates the phase difference from two signals, voltage and current. This method computes R. L and C value from phase difference($\theta$) and impedance value(Z) obtained by enforcing two other frequence stimulus under the guarding state.

• Resources Recycling
• /
• v.27 no.1
• /
• pp.55-63
• /
• 2018

Physical property changes of printed circuit board (PCB) according to heat treatment conditions were investigated. The heat treatment was carried out in air and nitrogen atmosphere at temperature range from $200^{\circ}C$ to $325^{\circ}C$. Thermogravimetric analysis showed that the PCB was pyrolyzed in two steps. The thickness of PCB expanded by 11~28% at about $300^{\circ}C$ in both air and nitrogen atmosphere as layer disintegration occurred. Mechanical strength of PCB decreased from 338.4 MPa to 20.3~40.2 MPa due to the delamination caused by the heat treatment. The heated printed circuit boards were crushed and sieved for analysis of density distribution and liberation degree of copper according to particle size. As a result of the density distribution measurement, non metallic particles and copper particles were concentrated into different size range, respectively. The liberation degree of copper was improved from 9.3% to 100% at size range of $1,400{\sim}2,000{\mu}m$ by heat treatment.

• Journal of electromagnetic engineering and science
• /
• v.14 no.1
• /
• pp.43-45
• /
• 2014

We propose a printed circuit board (PCB)-embedded antenna for millimeter-wave chip-to-chip communication. The antenna is 0.18 mm in height which is 1/20 wavelength at 80 GHz. In order to realize such a low profile, a zeroth-order resonator antenna with a periodic array of four unit cells is employed, and its geometry is optimized to cover an 8-GHz bandwidth from 76 to 84 GHz. With this;the antenna is capable of radiating in a direction parallel to the board length despite the short distance between the ground and the radiator. Simulation and measurement results show that the optimized design has low reflection coefficients and consistent radiation patterns throughout the target bandwidth.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.169-173
• /
• 2003

We demonstrated the applicability of dry film photoresist (DFR) in photolithography process for fine pitch solder bumping on the polytetrafluoroethylene (PTFE/Teflon) printed circuit board (PCB). The copper lines were formed with $100\;{\mu}m$ width and $18\;{\mu}m$ thickness on the PTFE test board, and varying the gaps between two copper lines in a range of $100-200\;{\mu}m$. The DFRs of $15\;{\mu}m$ thickness were laminated by hot roll laminator, by varying laminating temperature from $100^{\circ}C\;to\;150^{\circ}C$ and laminating speed. We found the optimum process of DFR lamination on PTFE PCB and accomplished the formation of indium solder bumps. The optimum lamination condition was temperature of $150^{\circ}C$ and speed of about 0.63 cm/s. And the smallest size of indium solder bump was diameter of $50\;{\mu}m$ with pitch of $100\;{\mu}m$.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.1
• /
• pp.21-28
• /
• 2004

We have demonstrated the applicability of dry film photoresist (DFR) in photolithography process for fine pitch solder bumping on the polytetrafluoroethylene (PTFE/Teflon ) printed circuit board (PCB). The copper lines were formed with 100$\mu\textrm{m}$ width and 18$\mu\textrm{m}$ thickness on the PTFE test board, and varying the gaps between two copper lines in a range of 100-200$\mu\textrm{m}$. The DFRs of 15$\mu\textrm{m}$ thickness were laminated by hot roll laminator, by varying laminating temperature from $100{\circ}C$ to 15$0^{\circ}C$ and laminating speed from 0.28-0.98cm/s. We have found the optimum process of DFR lamination on PTFE PCB and accomplished the formation of indium solder bumps. The optimum lamination condition was temperature of $150^{\circ}C$ and speed of about 0.63cm/s. And the smallest size of indium solder bump was diameter of 50$\mu\textrm{m}$ with pitch of 100$\mu\textrm{m}$.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.1
• /
• pp.16-22
• /
• 2002

The Proposed contactless charger employs a Pair of neighboring Printed circuit board (PCB) windings as a contactless energy transfer device, thereby making it amenable to low-Profile designs and suitable for applications to the portable telecommunication/computing electroncis in which stringent requirements for height, space, and reliability have to be met. The performance of the proposed charger is confirmed with experiments on a prototype charger developed for cellular phones

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.6
• /
• pp.509-516
• /
• 2008

Multi-layer circuit card for semiconductor inspection was fabricated by LTCC technology. After a proper impedance design without electrical interference, ceramic tapes with the composition of $CaO-Al_2O_3-SiO_2-B_2O_3$ glass and $Al_2O_3$ were prepared. The electrode with silver paste printed on the tape. Printed ceramic sheets were then laminated and sintered. Densities and dielectric properties were measured. The microstructure, fracture surface of the region of via and matching state of substrate-electrode were observed. The durability of plated outside electrode were examined by hardness and scratch test.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 1999.11a
• /
• pp.7-10
• /
• 1999

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.1-6
• /
• 2001

In this article, the fundamental concept, characteristics and application potentials of coreless printed-circuit-board (PCB) transformers are described. Coreless PCB transformers do not have the limitations associated with magnetic cores, such as the frequency limitation, magnetic saturation and core losses. In addition, they eliminate the manual winding process and its associated problems, including labor cost, reliability problems and difficulties in ensuring transformer quality in the manufacturing process. The parameters of the printed windings can be precisely controlled in modern PCB technology. Because of the drastic reduction in the vertical dimension, coreless PCB transformers can achieve high power density and are suitable for applications in which stringent height requirements for the circuits have to be met. A transformer's power density of $24W/cm^2$ has been reported in a power conversion application. When used in an isolation amplifier application, coreless PCB transformers tested so far enable the amplifier to achieve a remarkable linear frequency range of 1MHz, which is almost eight times higher than the frequency range of 120kHz in existing Integrated-Circuit products. PCB materials offer extremely high isolation voltage, typically from 15kV to 40kV, which is higher than many other isolation means such as optocouplers. It is envisaged that coreless PCB transformers can replace traditional core-based transformers in some industrial applications. Their application potentials deserve more attention and exploration.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.11a
• /
• pp.87-88
• /
• 2007