• Journal of Korean Neurosurgical Society
• /
• 제53권6호
• /
• pp.331-336
• /
• 2013

Objective : The offset connector can allow medial and lateral variability and facilitate intralaminar screw incorporation into the construct. The aim of this study was to compare the biomechanical characteristics of C7 intralaminar screw constructs with and without offset connector using a three dimensional finite element model of a C6-7 cervical spine segment. Methods : Finite element models representing C7 intralaminar screw constructs with and without the offset connector were developed. Range of motion (ROM) and maximum von Mises stresses in the vertebra for the two techniques were compared under pure moments in flexion, extension, lateral bending and axial rotation. Results : ROM for intralaminar screw construct with offset connector was less than the construct without the offset connector in the three principal directions. The maximum von Misses stress was observed in the C7 vertebra around the pedicle in both constructs. Maximum von Mises stress in the construct without offset connector was found to be 12-30% higher than the corresponding stresses in the construct with offset connector in the three principal directions. Conclusion : This study demonstrated that the intralaminar screw fixation with offset connector is better than the construct without offset connector in terms of biomechanical stability. Construct with the offset connector reduces the ROM of C6-7 segment more significantly compared to the construct without the offset connector and causes lower stresses around the C7 pedicle-vertebral body complex.

• 대한기계학회논문집A
• /
• 제22권3호
• /
• pp.595-602
• /
• 1998

Specimens of 304 stainless steel were tested to failure at elevated temperatures under multiaxial stress states, uniaxial tension using smooth bar specimens, biaxial shearing using double shear bar specimens, and triaxial tension using notched bar specimens. Rupture times are compared for uniaxial, biaxial, and triaxial stress states with respect to the maximum principal stress, the von Mises effective stress, and the principal facet stress. The results indicate that the principal facet stress gives the best correlation for the material investigated, and this parameter can predict creep life data under multiaxial stress states with rupture data obtained with specimens under uniaxial stresses. The results also suggest that grain boundary cavitation, coupled with localized deformation processes such as grain boudary sliding, controls the lifetimes of the specimens.

• Journal of Mechanical Science and Technology
• /
• 제19권7호
• /
• pp.1432-1440
• /
• 2005

High-temperature rupture behavior of 5083-Al alloy was tested for failure at 548K under multiaxial stress conditions: uniaxial tension using smooth bar specimens, biaxial shearing using double shear bar specimens, and triaxial tension using notched bar specimens. Rupture times were compared for uniaxial, biaxial, and triaxial stress conditions with respect to the maximum principal stress, the von Mises effective stress, and the principal facet stress. The results indicate that the von Mises effective and principal facet stresses give good correlation for the material investigated, and these parameters can predict creep life data under the multiaxial stress states with the rupture data obtained from specimens under the uniaxial stress. The results suggest that the creep rupture of this alloy under the testing condition is controlled by cavitation coupled with highly localized deformation process, such as grain boundary sliding. It is also conceivable that strain softening controls the highly localized deformation modes which result in cavitation damage in controlling rupture time of this alloy.

• Steel and Composite Structures
• /
• 제26권6호
• /
• pp.771-791
• /
• 2018

This paper deals with the low velocity impact response and dynamic stresses of composite sandwich truncated conical shells (STCS) with compressible or incompressible core. Impacts are assumed to occur normally over the top face-sheet and the interaction between the impactor and the structure is simulated using a new equivalent three-degree-of-freedom (TDOF) spring-mass-damper (SMD) model. The displacement fields of core and face sheets are considered by higher order and first order shear deformation theory (FSDT), respectively. Considering continuity boundary conditions between the layers, the motion equations are derived based on Hamilton's principal incorporating the curvature, in-plane stress of the core and the structural damping effects based on Kelvin-Voigt model. In order to obtain the contact force, the displacement histories and the dynamic stresses, the differential quadrature method (DQM) is used. The effects of different parameters such as number of the layers of the face sheets, boundary conditions, semi vertex angle of the cone, impact velocity of impactor, trapezoidal shape and in-plane stresses of the core are examined on the low velocity impact response of STCS. Comparison of the present results with those reported by other researchers, confirms the accuracy of the present method. Numerical results show that increasing the impact velocity of the impactor yields to increases in the maximum contact force and deflection, while the contact duration is decreased. In addition, the normal stresses induced in top layer are higher than bottom layer since the top layer is subjected to impact load. Furthermore, with considering structural damping, the contact force and dynamic deflection decrees.

• 대한치과교정학회지
• /
• 제46권3호
• /
• pp.155-162
• /
• 2016

Objective: The aim of this study was to investigate whether labial tooth inclination and alveolar bone loss affect the moment per unit of force ($M_t/F$) in controlled tipping and consequent stresses on the periodontal ligament (PDL). Methods: Three-dimensional models (n = 20) of maxillary central incisors were created with different labial inclinations ($5^{\circ}$, $10^{\circ}$, $15^{\circ}$, and $20^{\circ}$) and different amounts of alveolar bone loss (0, 2, 4, and 6 mm). The $M_t/F$ necessary for controlled tipping ($M_t/F_{cont}$) and the principal stresses on the PDL were calculated for each model separately in a finite element analysis. Results: As labial inclination increased, $M_t/F_{cont}$ and the length of the moment arm decreased. In contrast, increased alveolar bone loss caused increases in $M_t/F_{cont}$ and the length of the moment arm. When $M_t/F$ was near $M_t/F_{cont}$, increases in Mt/F caused compressive stresses to move from a predominantly labial apical region to a palatal apical position, and tensile stresses in the labial area moved from a cervical position to a mid-root position. Although controlled tipping was applied to the incisors, increases in alveolar bone loss and labial tooth inclination caused increases in maximum compressive and tensile stresses at the root apices. Conclusions: Increases in alveolar bone loss and labial tooth inclination caused increases in stresses that might cause root resorption at the root apex, despite the application of controlled tipping to the incisors.

• Restorative Dentistry and Endodontics
• /
• 제31권6호
• /
• pp.427-436
• /
• 2006

본 연구의 목적은 3차원유한요소분석법을 이용하여 정상 상악 제2소구치의 협측부의 응력분포에 다양한 교합응력이 미치는 영향을 평가하고자 하였다. 상악 제2소구치의 3차원유한요소모델을 형성한 후 형성된 모델에 3종류의 정적인 500N 점하중의 응력조건을 부여하였다. ANSYS 프로그램 (Swanson Analysis Systems, Inc., Houston, USA)으로 최대주응력과 최소주응력을 4개의 수평면 상(CEJ 상방 1 mm, CEJ 상방 0.5 mm, CEJ, CEJ 하방 0.5 mm)에서 분석하여 다음 결과를 얻었다. 1. peak stress가 협측 백악법랑경계를 따라 비대칭적인 모습으로 나타났다. 2. 압축응력 값은 법랑질의 압축파괴응력 범위 내에 있었지만 인장응력은 법랑질의 인장파괴응력 범위를 넘어섰다. 3. 비우식성치경부병소를 발생시키는 주요인은 설측교두의 협측경사면에 가해지는 교합압에 의한 인장응력이라고 보여진다.

• 대한치과보철학회지
• /
• 제18권1호
• /
• pp.15-35
• /
• 1980

The purpose of this study was to investigate stresses in the various components of fixed partial dentures restoring the posterior teeth of the lower jaw, and to measure quantitatively the effects of certain modifications in structural design on the stresses in the restorations using two-dimensional photoelasticity. Two-dimensional photoelastic methods were used in this study. Several models of fixed partial dentures were constructed. Shoulder less margins and anatomic occlusal reduction were incorporated in Model 1. Rounded shoulders and flat occlusal reduction were incorporated in Model 2, while Model 3 was a cantilever fixed partial denture. Other similar fixed partial dentures were constructed with V and U notches deliverately included in the region of the fixed joints for comparative reasons. The birefringent materials used in this study were PSM-1 and PSM-5 in standard sheets. PSM-1 was used for constructing the substructure, and PSM-5 was used in making the components of the fixed partial dentures. The two materials were used in the construction of composite photoelastic models. Improved artificial stone was used to represent dental cement in luting the composite photoelastic models. Static loading procedures were used at preplanned sites to represent occlusal loads in the mouth. 35 mm color and B/W film were used to record isochromatics in accordance with photoelastic procedures. Data reduction was performed using the grid method, which helped in, the mathematical integration procedure (Shear difference method) to separate the principal stresses. The results were as follows. 1. Fixed partial dentures do not function in bending as a symmetrical beam. Alternate areas of tension and compression were demonstrated when multiple contact loading was used. 2. The weakest part in posterior fixed partial dentures is the fixed joint. 3. (1) Models I and modified Model I were loaded on the pontic using a 50 pound vertical static load. The shear stress near the posterior fixed joint in Model 1 (U notches) was+129.4 p.s.i., and at the same fixed joint in modified Model 1 (V notches) was+239.4 p.s.i. The concentration of stress in fixed joint was reduced by 50% when U notches replaced the V notches. (2) Modified Model 2 was loaded using a multiple contact loader at a total load of 125 pounds. The difference between the principal stresses (${\sigma}_1-{\sigma}_2$), shear stress, at the V notches was+600 p.s.i., and at the U notches was+3l7 p.s.i. The shear stress was reduced by 50% when U notches replaced the V notches. V-grooves at the fixed joints should be avoided, and should be replaced by regular shaped U-grooves. 4. Cantilever fixed partial dentures had much higher stresses at the fixed joint than fixed partial dentures that were attached at both ends.

• 한국지반공학회지:지반
• /
• 제13권1호
• /
• pp.35-46
• /
• 1997

실제지반에 하중이 가하여 질 경우 발생되는 주응력회전시의 지반거동을 해석하기 위하여 등 방단일경화구성모델이 적용되었다. 이 모델에 의한 해석결과는 Ko압밀점토의 중공 원통형 공시체에 여러가지 응력경로를 대상으로 실시된 일련의 비틀림전단시험에 의한 시험치와 좋은 일치를 보이고 있다. 결국 주응력회전시의 지반거동은 등방압축 및 통상적인 압밀비배수 삼축압축시험으로 얻을 수 있는 간단한 정보만을 활용한 이 모델로 예측될 수 있음을 알았다. 비틀림전단시험결과와 해석결과 모두에서 등방탄소성 지반거동을 최초재하 (primary loading)단계 동안에 관찰할 수 있었다. 그러나, Ko압밀응력의 등방항복면내에서 감하나 수재하와 같은 응력 반전을 실시할 경우 최대주변형률증분 방향의 해석치는 시험치와 일치하지 않았다. 이는 응력반전시의 지반거동을 해석하기 위하여는 등방경화모델 (isotropic hardening model)보다 는 이동경화모델(kinematic hardening model)이 개발되어야함을 의미한다. 또한 본 연구에서는 일공간에서 변형률증분벡터의 시험치가 관련흐름법칙 및 비관련흐름법칙에 의한 해석법과 비교되었다.

• 대한기계학회논문집
• /
• 제15권2호
• /
• pp.404-412
• /
• 1991

In the design of high speed machinery, designers must consider the problem of possible structural failure due to excessive dynamically varying stresses, which are induced by the varying external loads and internal inertia forces, in the links of the mechanism. A study of the dynamically induced stresses would indicate what values of the minimum permissible fatigue strength should be for safe mechanism operation. This paper investigates the nature of the stress fluctuation in high speed mechanism on the basis of the effects of both the loads and the friction. The latter is apt to be neglected in the usual analysis in spite of the fact that it is always generated in the operating machinery. The analysis is performed on the coupler of the slider-crank mechanism for illustrative purposes and the results are expressed in a non-dimensional form for design applications.

• Structural Engineering and Mechanics
• /
• 제39권3호
• /
• pp.303-316
• /
• 2011

Experimental tests have shown that glass exhibits very different strengths when tested under biaxial and uniaxial conditions. This paper presents a study on the effects of biaxial stresses on the notional ultimate strength of glass. The study involved applying the theory of elasticity and finite element analysis of the Griffith flaw in the micro scale. The strain intensity at the tip of the critical flaw is used as the main criterion for defining the limit state of fracture in glass. A simple and robust relationship between the maximum principal stress and the uniaxial stress to cause failure of the same glass specimen has been developed. The relationship has been used for evaluating the strength values of both new and old annealed glass panels. The characteristic strength values determined in accordance with the test results based on 5% of exceedance are compared with provisions in the ASTM standard.