• 한국안전학회지
• /
• 제25권3호
• /
• pp.71-77
• /
• 2010

This paper presents the results of a study on flexural capacity of large size RC slabs strengthened with carbon fiber reinforced polymer(CFRP) plates. A total of 5 specimens of 6.0m length were tested in four point bending after strengthening them with externally bonded CFRP plates. The CFRP plates were bonded without prestress and with two prestress levels, 0.4% and 0.6% of CFRP plate strain. Test variables included the type of strengthening, prestressing level, and the effects according to each test variables are analysed. The experimental results show that proposed methods can increase significantly the flexural capacity such as strength, stiffness of the beam and the increase ranged between 36.2% and 63.2% of the load-carrying capacity of the control beams. The non-prestressed specimen failed by separation of the plate from the beam due to premature debonding while most of the prestressed specimens failed by CFRP plate fracture. And the cracking loads and maximum loads were increased proportionally to the prestress level.

• Computers and Concrete
• /
• 제6권6호
• /
• pp.451-472
• /
• 2009

Based on a numerical method to analyse the full-range behaviour of prestressed concrete beams with unbonded tendons, parametric studies are carried out to investigate the influence of 11 parameters on the curvature ductility of unbonded prestressed concrete (UPC) beams. It is found that, among various parameters studied, the depth to prestressing tendons, depth to non-prestressed tension steel, partial prestressing ratio, yield strength of non-prestressed tension steel and concrete compressive strength have substantial effects on the curvature ductility. Although the curvature ductility of UPC beams is affected by a large number of factors, rather simple equations can be formulated for reasonably accurate estimation of curvature ductility. Conversion factors are introduced to cope with the difference in partial safety factors, shapes of equivalent stress blocks and the equations to predict the ultimate tendon stress in BS8110, EC2 and ACI318. The same equations can also be used to provide conservative estimates of ductility of UPC beams with compression steel.

• Steel and Composite Structures
• /
• 제24권3호
• /
• pp.323-337
• /
• 2017

This paper presents the results of a comprehensive experimental investigation on the compressive behaviour of steel tube-confined concrete (STCC) stub columns with active and passive confinement. To create active confinement in STCC columns, an innovative technique is used in which steel tube is laterally pre-tensioned while the concrete core is simultaneously pre-compressed by applying pressure on fresh concrete. A total of 135 STCC specimens with active and passive confinement are tested under axial compression load and their compressive strength, ultimate strain capacity, axial and lateral stress-strain curves and failure mode are evaluated. The test variables include concrete compressive strength, outer diameter to wall thickness ratio of steel tube and prestressing level. It is shown that applying active confinement on STCC specimens can considerably improve their mechanical properties. However, applying higher prestressing levels and keeping the applied pressure for a long time do not considerably affect the mechanical properties of actively confined specimens. Based on the results of this study, new empirical equations are proposed to estimate the axial strength and ultimate strain capacity of STCC stub columns with active and passive confinement.

• 한국방재학회 논문집
• /
• 제1권2호
• /
• pp.103-114
• /
• 2001

PSC box girder의 정착부 설계방법들을 비교해본 결과, 기존 시방서에 따른 설계방법에서는 다수의 정착구에 긴장력이 작용할 때 긴장력의 작용순서와 그 크기에 따른 응력의 중첩효과를 고려할 수 없는 단점을 가지고 있었고, 3차원 유한요소해석을 이용한 설계에서는 응력집중부와 응력흐름을 정확히 파악할 수는 있지만 부재의 단면력을 산정하기가 매우 번거롭고 까다롭다는 단점을 가진다. 그러나 strut-tie 모델을 이용한 설계법에서는 긴장력의 긴장순서에 따른 응력중첩효과를 고려할 수 있고 부재의 단면력의 산정 또한 매우 간편하여 긴장력의 도입순서에 의해 변화하는 응력의 흐름을 잘 파악하여 strut-tie로 구성된 트러스 부재들의 기하학적 조건을 만족하도록 유의한다면 정착부의 설계에 가장 적합한 설계방법이라 할 수 있다.

• 한국안전학회지
• /
• 제30권5호
• /
• pp.67-73
• /
• 2015

In this paper, the simple truss model was modified to predict the punching shear strength of long-span prestressed concrete (PSC) deck slabs under wheel load including the effects of transverse prestressing and long span length between girders. The strength of the compressive zone arounding punching cone was evaluated by the stiffness of inclined strut which was modified by considering aging effective modulus. The stiffness of springs which control lateral displacement of the roller supports consists of the steel reinforcement and prestressing which passed through the punching cone. Initial angle of struts was determined by the experimental observation to compensate for uncertainties in the complexities of the punching shear. The validity of computed punching shear strength by modified simple truss model was shown by comparing with experimental results and the experimental results were also compared with existing punching shear equations to determine level of predictability. The modified simple truss model appeared to better predict the punching shear strength of PSC deck slabs than other available equations. The punching shear strength, which was determined by snap-through critical load of modified simple truss model, can be used effectively to examine punching shear strength of long span PSC deck slabs.

• 한국전산구조공학회논문집
• /
• 제19권2호
• /
• pp.115-124
• /
• 2006

본 연구에서는 상용 압연형강과 콘크리트 합성거더인 PSSC(Prestressed Steel and Concrete) 거더의 1, 2차 긴장력과 활하중을 최적설계 하였다. 다단계 긴장에 따른 1, 2차 긴장력과 활하중을 설계변수로 삼았으며, 최종 활하중을 목적함수로 정하였다. 시공단계에 따른 강주형, 충전 콘크리트, 슬래브의 상연과 하연의 허용응력을 설계 조건으로 하였다. 설계 최적화는 상용 프로그램 Matlab의 최적화 모듈을 이용하여 수행되었다. 형고의 변화, 콘크리트 압축강도의 변화, 헌치 높이의 변화 등 다양한 조건에 빠른 최적 설계를 시도하였고, 연구 결과로부터 강선배치, 콘크리트 압측강도 등이 설계에 큰 영향을 미치는 것을 알 수 있었다.

• 한국전산구조공학회논문집
• /
• 제22권3호
• /
• pp.199-209
• /
• 2009

본 논문은 단조하중을 받는 초고강도 섬유보강 콘크리트 I형보의 파괴거동에 대한 3차원 유한요소해석을 수행하였다. 보통 또는 고강도 콘크리트의 구성방정식과 달리 초고강도 섬유보강 콘크리트의 재료적 특성을 나타내기 위해 인장변형률 경화관계를 고려한 탄소성 파괴역학 모델을 제안하였다. 인장영역에서는 인장경화 변형률을 고려한 다차원적 균열기준을 정의하였고, 압축영역에서는 associated flow rule을 고려한 Drucker-Prager기준을 채택하여 해석을 수행하였다. UHPFRCI형보의 지간, 프리스트레스 하중 및 단면의 영향에 관한 수치해석 결과를 실험 거동와 비교한 결과 정확한 해석 결과를 보여주었다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.57-60
• /
• 2005

The objective of this paper is to investigate and analyze the behaviour of prestressed I section structural members constructed with ultra high perfomance steel fiber reinforced cementitious concrete (SFR-UHPC). This material is known as reactive powder concrete (RPC) mixed with domestic materials and its compressive strength is over 150MP. The parameters of test specimens were span to depth ratio, prestressing force, prestressing wire placement and web width. Most influential parameter to determine the failure mode between shear and flexural action was proved to be shear span ratio. The characteristics of ultra high-strength concrete is basically brittle, but due to the steel fiber reinforcement behaviour of this structure member became ductile after the peak load. As a result of the test, the stress block of compressive zone should be redefined. The proposed analytical calculation of internal force capacity based by plastic analysis gave a good prediction for the shear and flexural strength of specimens. The numerical verification of the finite element model which constitutive law developed for Mode I fracture of fiber reinforced concrete correctly captured the overall behaviour of the specimens tested.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.98-101
• /
• 2006

As an alternative of conventional prestressed concrete (PSC) girders, various types of PSC girders are being developed and applied in bridge structures. Incrementally prestressed concrete girder is one of these newly developed girders. According to design concept, these new types of PSC girders have considerable advantages to reduce their self-weight and make spans longer. However, dynamic interaction between bridge superstructures and passing trains would be sometimes one of critical issues in these more flexible railway bridges. Therefore, it is very important to evaluate modal parameters of newly designed bridges before conducting dynamic analyses. In the present paper, a 25 meters long full scale PSC girder was fabricated as a test specimen and modal testing was carried out to evaluate modal parameters including natural frequencies and modal damping ratios at every prestressing stage. In the modal testing, a digitally controlled vibration exciter as well as an impact hammer is applied to obtain frequency response functions more exactly and the modal parameters are evaluated varying with construction stages. Prestressed force effects on changes of modal parameters are analyzed at every incremental prestressing stage.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.205-208
• /
• 2008

강재매입형 합성교각은 강재의 구속효과에 의하여 심부콘크리트의 내력상승을 유발하고, 또한 심부 콘크리트로 인한 강재의 좌굴 보강효과로 단면과 자중을 증가시키지 않고도 부재의 내력이 증가하게 만들 수 있어 내진 설계시 필요한 여러 조건들을 충족시키는 구조물이라 할 수 있다. 조립식 강재매입형 합성교각에서는 일체형으로 하는 경우에는 프리스트레스를 도입하지 않아도 되지만 세그먼트를 나눌 경우에는 이음부 균열제어를 위해 일정 수준의 프리스트레스를 도입해야 한다. 도입되는 프리스트레스에 의해 합성단면에 발생하는 초기 응력과 변형은 콘크리트의 장기거동에 의해서 변화하게 되고 설계시 이를 검토해야 한다. 이 논문에서는 세그먼트로 나누어진 프리캐스트 합성교각에 프리스트레스를 도입한 후 강연선에 부착된 로드셀과 철근, 콘크리트, 강관의 변형률 변화를 통해 프리스트레스 손실량을 검토하여 분석하였다.