• 한국압력기기공학회 논문집
• /
• 제15권2호
• /
• pp.40-49
• /
• 2019

In this paper, failure probabilities of the OPR1000 reactor vessel under pressurized thermal shock (PTS) were estimated using the probabilistic fracture mechanics code, R-PIE. Input variables of initial crack distribution, crack size, copper contents, and upper shelf toughness were selected for the sensitivity analyses. A wide range of the input data were considered. Through-wall cracking frequencies determined by the product of the vessel failure probability and the corresponding occurrence frequency of the transient were also compared to the acceptance criterion. The results showed that transient history had the most significant impact on the vessel failure probability. Moreover, conservative assumptions resulted in extremely high through-wall cracking frequencies.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2017년도 학술발표회
• /
• pp.265-269
• /
• 2017

Because of abrupt changes for velocity in water, transient flow is occurred in practical life. To reduce and avoid the high or low pressure of pipe network system, various surge protection facilities are used to prevent the risk in pipe network system. Especially, we focused on study not only preventing positive and negative pressure but also selecting adequate equipment for high pressurized pipelines. Several critical cases were considered by undertaking a steady state hydraulic study and transient dynamic simulation and we suggested that the surge vessel of various surge protection system was recommended to control high and low pressures on pipeline system in perspective.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제31회 추계학술대회논문집
• /
• pp.78-81
• /
• 2008

A numerical study of the unsteady flow in an over-expanded thrust optimized contour and compressed truncated perfect rocket nozzle is carried out in present paper. These rocket nozzles are subject to flow separation in transient phase at engine start-up and/or engine shut-down. The separation flow structures at different pressure ratios are observed. The start-up process exhibits two different shock structures such as FSS (Free Shock Separation) and RSS (Restricted Shock Separation). For a range of pressure ratios, hysteresis phenomenon occurs between these two separation patterns. A three-dimension compressible Navier-Stokes solver is used for the present study. One equation Spalart-Allmaras turbulence model is selected. The computed nozzle wall pressures show a good agreement with the experimental measurements. Present results have shown that present code can be used for the analysis of the transient flows in nozzle.

• 한국자동차공학회논문집
• /
• 제10권3호
• /
• pp.201-208
• /
• 2002

In this paper, the control strategy of ratio changing system for a metal belt CVT adopting primary pressure regulation is developed, and the shirting performance of pressure regulating type CVT with the suggested control strategy is investigated. The control strategy suggested in this study is composed of 2 feedback loop, one is speed ratio feedback and the other is primary pressure feedback. The pressure feedback is adopted to ensure prohibiting a belt slip during transient period in a fast downshift mode. Simulation results show that the system with suggested control strategy gives appropriate response time and tracking Performance for upshift and also gives a proper primary pressure which can prohibit the belt slip. In addition, it is fecund that the given system has an acceptable servo property in tracking the target speed ratio and robustness for the disturbance of line pressure.

• 한국자동차공학회논문집
• /
• 제1권3호
• /
• pp.1-11
• /
• 1993

An experimental study was carried out to evaluate the characteristics of transient performance of carburettered gasoline engine under rapid accelerating transient driving conditions. In order to evaluate the characteristics of transient performance quantitatively, the concept of dead time $t_d$ response delay time $t_r$ are introduced. Performance parameters such as air mass fiowrate Gat, engine speed N, manifold boost pressure Pb, and output torque T are measured simultaneously during the rapid opening of the throttle valve by the stepping motor. During the rapid opening of the throttle valve, air mass fiowrate Gat is increased immediately without delay time, but response of engine revolution N, and output torque T are delayed. Therefore hesitation, and stumble phenomena are occurred. Dead time $t_d$ and response delay time $t_r$ of engine revolution N, which is extremely delayed comparing to other performance parameters, are respectively 0.2-0.3sec., 3.0-4.6sec., and dead time rate $t_d/{\Delta}t$ and response delay time rate $t_r/{\Delta}t$ are linearly increased with the throttle valve opening rate ${\theta}$ during the acceleration from 12 degree to 20 degree at 1250rpm.

• 한국자동차공학회논문집
• /
• 제12권5호
• /
• pp.12-18
• /
• 2004

Transient natures of diesel sprays are often characterized with spray visualization, since it is a non-intrusive and straightforward technique to be applied. However, as injection pressure is increased higher than a thousand bar in a modern direct injection diesel engine, very fine temporal and spatial resolutions in the spray visualization are required while sprays become optically denser. Discussed in this paper are macroscopic and microscopic spray visualization techniques and an example of image processing process for efficient and consistent measurement of spray parameters. The injection rate measurement method based on hydraulic pulse principle was suggested as a way of estimating injection velocity for transient diesel sprays. The spray visualization and injection rate measurement techniques were applied to analyze transient diesel sprays from a common-rail injection system and found to be practically effective.

• 한국자동차공학회논문집
• /
• 제8권4호
• /
• pp.10-17
• /
• 2000

This work presents an investigation of aerodynamic characteristics of fuel spray injected from a high pressure hollow cone swirl injector into a constant volume chamber. Laser tomography visualization was used to interrogate the fuel and air mixing characteristics and the effect of chamber pressure and temperature increase was analyzed, Preliminary results on spray development showed that mixing effect tends to increase with the increase of injection pressure and chamber gas pressure yielding a decrease of spray penetration and an attenuation of well-defined vortex structure. Topological analysis of the spray structure has been performed to initiate the understanding of mixing and vaporization process. For the present experimental conditions fuel injection pressure and chamber gas pressure appear as the dominant factors which govern the transient mixing characteristics. Moreover spray atmixation characteristics are improved by increasing chamber gas temperature.

• 대한기계학회논문집
• /
• 제12권5호
• /
• pp.984-991
• /
• 1988

본 연구에서는 유압관로에서 액주분리를 수반하는 유체 과도현상의 압력파형 에 때때로 관측되는 2단적 압력상승현상의 발생기구를 실험 및 이론적인 추론, 특성곡 선법을 사용한 수치해석을 통하여 명확히 구명함을 목적으로 한다.

• 한국추진공학회지
• /
• 제2권2호
• /
• pp.47-55
• /
• 1998

중형항공기용 터보팬엔진의 설계점, 탈설계점에 대한 정상상태 및 천이상태 성능해석을 수행하였다. 정상상태 성능해석은 설계점으로 선정한 지상최대추력조건과 탈설계점으로 선정한 최대상승조건과 순항조건에서 수행하였으며 부분부하 성능해석 결과 저압압축기 회전속도 90％RPM에서 가장 연료소모율이 적어 경제적임을 확인하였다. 천이상태 성능해석은 각각의 비행조건에서 연료의 Step증가, Ramp증가, Ramp감소, Step 증가 후 Ramp 감소의 경우에 대하여 수행하였다. 천이상태의 성능해석을 위해서는 압축기와 터빈의 일에 대한 조합이 필요한데, 일의 조합방정식에 포함된 잉여 토오크의 적분에는 Modified Euler Method를 적용하였다. 천이상태 성능해석 결과, 모든 비행조건에서 Step 및 Ramp 증가의 경우 고압압축기의 터빈입구온도가 제한온도를 초과하며, 최대상승조건에서 연료를 Step 또는 5.5초 이내의 Ramp 증가시킬 경우 고압압축기에서 실속이 발생함을 확인하였다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제3권1호
• /
• pp.64-68
• /
• 2001

An experimental study on the Joule-Thomson cryocooler with the mixed refrigerant (MR) is described in this paper, J-T refrigeration experiment was performed with a single stage regular air-conditioning compressor The mixed refrigerant in the experiment was composed of 75% mol fraction of $N_2$. 30% moi fraction of CH$_4$. 30% moi fraction of $C_2$H$_{6}$. 10% mot fraction of $C_3$H$_{8}$ and 15% mot fraction of iso-C$_4$H$_{10}$. Oil mist in the MR stream could be eliminated completely by the glass microfiber filter. Since a single stage compressor that had been designed thor R22 is not appropriate for high Pressure ratio of the mixed refrigerant especially during the transient period. two modifications were incorporated to regular J-T refrigeration cycle. First. a Portion of the MR was by-passed at the inlet of the heat exchanger and transferred directly to 7he suction of the compressor in the modified system. Second, a buffer volume was Prepared to change the mass flow rate of refrigerant. The pressure ratio in J-T expansion device was relieved at the beginning of the operation due to the by-Pass scheme. but it gradually decreased during the transient Process as some of the MR component condensed at low temperature. The buffer volume at the suction side was used to increase the MR gas density in the system after the transient cool-down period. Form the experiment with the modified system, the refrigerator could reach the lowest temperature of -152$^{\circ}C$ without cooling load. and about -15$0^{\circ}C$ with 5 W of cooling load . . . .