• 해양환경안전학회지
• /
• 제10권1호
• /
• pp.51-54
• /
• 2004

최근 양어 양식장은 증가하고 있으며 이러한 곳에 사용할 가열장치는 경울 수온 조절을 위해 사용된다. 해수 가열장치는 부식성이 높고 압력이 높은 곳에 사용하기 위하여 고강도와 내식성이 요구된다. 만약 저강도와 저내식성을 갖게 되면 결국 누설 또는 파손되어 해수오염을 일으킬 수 있다. 대부분의 부식은 정체된 액과 틈이 형성된 부위에서 부식의 발생이 일어난다. 이 연구에서는 430 스테인레스재를 크기 $15{\times}20{\times}3mmt$에 대하여 1N H2SO4 + 0.05N NaCl용액을 사용하여 틈부식을 시험하였다. 틈의 크기는 $0.24{\times}3{\times}15mmL$로 하였으며 외부에 300mV전위를 인가하였다. 실험 결과 틈 부식 유기 시간은 750초로 나타나고, 틈 전위 강화는 -320에서 -399mV로 나타나 부식의 주 원인이 전위강화 기구에 의해 발생하였다.

• 대한조선학회논문집
• /
• 제33권3호
• /
• pp.56-65
• /
• 1996

최근 재료 과학의 발달과 함께 선박의 초고속화를 추구함에 따라 높은 강도와 중량의 경량화를 동시에 만족시킬 수 있는 복합 재료에 대한 요구가 증대되고 있다. 샌드위치 구조 형식은 두껍고 약한 저밀도의 심재와 얇고 강한 고밀도의 면재가 접착된 복합 구조의 한 형태로서 두 개의 면재가 중립 축으로부터 멀리 떨어지게 됨으로써 2차 모멘트가 크게 되어 구조의 강성을 증가시킬 수 있는 가장 효과적인 경량의 구조 형식이다. 본 연구에서는 샌드위치 평판 구조가 분포 하중, 압축 하중, 전단 하중 및 이 들의 복합하중을 받을 때의 응력 및 좌굴 하중을 Rayleigh-Ritz법을 이용하여 정밀 해석하였다. 그리고, 샌드위치 평판에 대한 초기 설계에 응용이 가능하도록 좌굴응력 외에 Wrinkling 응력에 관한 제한조건을 고려하여 샌드위치 평판의 최소 중량 설계를 수행하였다.

• 동굴
• /
• 제76호
• /
• pp.37-42
• /
• 2006

The Dielectric Barrier Discharge (DBD) is a nonequilibrium gas discharge that is generated in the space between two electrodes, which are separated by an insulating dielectric layer. The dielectric layer can be put on either of the two electrodes or be inserted in the space between two electrodes. If an AC or pulse high voltage is applied to the electrodes that is operated at applied frequency from 50Hz to several MHz and applied voltages from a few to a few tens of kilovolts rms, the breakdown can occur in working gas, resulting in large numbers of micro-discharges across the gap, the gas discharge is the so called DBD. Compared with most other means for nonequilibrium discharges, the main advantage of the DBD is that active species for chemical reaction can be produced at low temperature and atmospheric pressure without the vacuum set up, it also presents many unique physical and chemical process including light, heat, sound and electricity. This has led to a number of important applications such as ozone synthesizing, UV lamp house, CO2 lasers, et al. In recent years, due to its potential applications in plasma chemistry, semiconductor etching, pollution control, nanometer material and large area flat plasma display panels, DBD has received intensive attention from many researchers and is becoming a hot topic in the field of non-thermal plasma.

• 한국CDE학회논문집
• /
• 제13권2호
• /
• pp.139-152
• /
• 2008

In order to survive worldwide competition, today's industries are experiencing strong pressure to introduce higher quality products with lower cost and shorter lead-time. Therefore, the role of design in the process of product development is increasing in significance. In this research, two methods for improving the design capability are proposed: construction of design environment and design automation using 3D CAD system. The designers and design process are the core of product design using 3D CAD system. In order to maximize the design performance, construction of the design environment including selection of a suitable system, designer training for best use of the system, establishment of an efficient design process, and stabilization of the environment are required. A method is suggested to construct design environment by systematizing the contents of the projects and consulting experiences carried out for various categories of business such as electronic devices, motorcycles, electricity parts, sanitary wares, injection molds, and die casing molds. Design automation helps reduce tedious and time-consuming jobs, simplify complicated and error-prone modeling and drawing works to shorten the lead time and improve the product quality. To develop a design automation system, understanding the process and the related knowledge on design are very important before implementing the system using API provided by 3D CAD system. In this research, an eight-step procedure is proposed for the development of a design automation system. These eight steps are analysis of needs, determination of specification, verification of specification using 3D CAD system, inspection of related API functions, programming, field test, application in practice, and maintenance. A case study in which five design automation systems in the design of turbine generators using the proposed method is introduced in detail. These systems play important roles in the generation of various output items including 3D models, drafts, material information, and NC data. The case study shows how effectively the design time is reduced and the quality improved using those systems.

• Nuclear Engineering and Technology
• /
• 제48권4호
• /
• pp.1009-1014
• /
• 2016

SiC-based ceramic composites are currently being considered for use in fuel cladding tubes in light-water reactors. The joining of SiC ceramics in a hermetic seal is required for the development of ceramic-based fuel cladding tubes. In this study, SiC monoliths were diffusion bonded using a Ti foil interlayer and additional Si powder. In the joining process, a very low uniaxial pressure of ~0.1 MPa was applied, so the process is applicable for joining thin-walled long tubes. The joining strength depended strongly on the type of SiC material. Reaction-bonded SiC (RB-SiC) showed a higher joining strength than sintered SiC because the diffusion reaction of Si was promoted in the former. The joining strength of sintered SiC was increased by the addition of Si at the Ti interlayer to play the role of the free Si in RB-SiC. The maximum joint strength obtained under torsional stress was ~100 MPa. The joint interface consisted of $TiSi_2$, $Ti_3SiC_2$, and SiC phases formed by a diffusion reaction of Ti and Si.

• Nuclear Engineering and Technology
• /
• 제41권7호
• /
• pp.875-884
• /
• 2009

We present three nuclear/hydrogen-related R&D activities being performed at KAIST: air-ingressed LOCA analysis code development, gas turbine analysis tool development, and hydrogen-production system analysis model development. The ICE numerical technique widely used for the safety analysis of water-reactors is successfully implemented into GAMMA, with which we solve the basic equations for continuity, momentum conservation, energy conservation of the gas mixture, and mass conservation of 6 species (He, N2, O2, CO, CO2, and H2O). GAMMA has been extensively validated using data from 14 test facilities. We developed a tool to predict the characteristics of HTGR helium turbines based on the throughflow calculation with a Newton-Raphson method that overcomes the weakness of the conventional method based on the successive iteration scheme. It is found that the current method reaches stable and quick convergence even under the off-normal condition with the same degree of accuracy. The dynamic equations for the distillation column of HI process are described with 4 material components involved in the HI process: H2O, HI, I2, H2. For the HI process we improved the Neumann model based on the NRTL (Non-Random Two-Liquid) model. The improved Neumann model predicted a total pressure with 8.6% maximum relative deviation from the data and 2.5% mean relative deviation, and liquid-liquid-separation with 9.52% maximum relative deviation from the data.

• 한국결정학회지
• /
• 제1권1호
• /
• pp.19-28
• /
• 1990

단결정 6H-SiC는 에너지갭이 3.0eV인 반도체로서 청색발광소자 및 고온반도체소자로 응용이 기대되는 재료이다. 본 연구에서는 청색발광소자 제작을 위해 6H-SiC 단결정을 승화법으로 성장시켰다. 승화법으로 성장시 성장도가니내의 온도구배를 44℃/cm, 성장온도는 1800-1990℃ 압력은 50-1000 mTorr이었다. 사용한 종자정은 에치슨법으로 성장시킨 SiC 단결정을 사용하였다. 성장된 6H-SiC 결정은 종자징위에 epitaxial growtll를 하였음을 편광현미경과 Back reflection Xray Laue 법으로 확인하였다. 성장조건을 변화시켰을 때 생성되는 결정상의 변화를 XRD로 조사하였다. 성장 온도가 1840℃ 이상일 경우에는 6H-SiC이 성장되었으며, 그 이하에서는 6H-SiC가 성장되었다. 또한 3C-SiC는 저온 저파포화도 성장조건에서 성장되는 상임을 확인하였다. van der Pauw측정법에의한 전기적 특성을 조사하였는데, 전도형은 p형이고 hole 농도와 이동도는 7.6x1014cm-3와 19cm2 V-1sec-1였다.

• Corrosion Science and Technology
• /
• 제11권6호
• /
• pp.263-269
• /
• 2012

Copper alloys are commonly applied to ship's propellers, pumps and valves which are serviced in seawater due to their good castability and corrosion resistance. In the environment of high flow velocity, however, erosion damage predominates over corrosion damage. In particular, the cavitation in seawater environment accelerates surface damage to copper alloys, resulting in degradation of products and economic losses and also threatening safety. The surface was coated with WC-27NiCr by high velocity oxygen fuel(HVOF) spraying technique to attain durability and cavitation resistance of copper alloys under high velocity/pressure flow. The cavitation test was performed for the WC-27NiCr coating deposited by HVOF in seawater at the amplitude of $30{\mu}m$ with seawater temperature. The cavitation at $15^{\circ}C$ caused exfoliation of the coating layer in 17.5 hours while that of $25^{\circ}C$ caused the exfoliation in 12.5 hours. When the temperature of seawater was elevated to $25^{\circ}C$ from $15^{\circ}C$, more damage was induced by over 160%. Although WC-27NiCr has good durability, corrosion resistance and eletrochemical stability, the cavitation damage rate of the coating layer could remarkably increase at the elevated temperatures under cavitation environments.

• 한국재료학회지
• /
• 제3권5호
• /
• pp.521-528
• /
• 1993

니켈-흑연 복합분말은 고온 고압하에서 수소개스를 사용하여 ammoniacal황산니켈염 수용액으로 부터 니켈이온을 흑연코어표면에 석출시켜 제조하였으며, SEM. X-선 회절분석, 입도 및 화학분석 등을 이용하여 환원속도 및 니켈코팅층의 특성에 미치는 코팅 촉매제 Anthraquinone$(C_6H_4COC_6H_4 CO)$ 의 영향을 조사하였다. 코팅촉매제의 입도 및 첨가량 변호에 따라 수소개스 주입 후 환원반응이 시작되기 까지 필요한 잠복기는 22~70분 정도 이었으며, 흑연코어 표면의 니켈코팅층은 포도송이 모양(botryoidal)인 미립의 니켈 nodule(2-4$\mu\textrm{m}$)로 형성되었다. 또한 코팅촉매제의 첨가량이 증가함에 따라 코팅용액중 니켈이온의 환원속도는 증가하여 0.2gr/$\ell$첨가시 4.5gr/$\ell$/min를 나타내었다.

• 한국재료학회지
• /
• 제23권2호
• /
• pp.135-142
• /
• 2013

The Ti-6Al-4V extra low interstitial (ELI) alloy has been widely used as an orthopedic implant material because of its excellent mechanical properties and biocompatibility. However, it still has many problems, including a high elastic modulus and toxicity of the Al and V elements. Therefore, non-toxic biomaterials with a low elastic modulus need to be developed. A high energy mechanical milling (HEMM) process is introduced to improve the effect of sintering. Rapid sintering of spark plasma sintering (SPS) under pressure was used to make an ultra fine grain of Ti-25 wt.%Nb-7 wt.%Zr-10 wt.%Mo-(10 wt.%CPP) composites with bio-attractive elements for increasing strength. These composites were fabricated by SPS at $1000^{\circ}C$ at 60 MPa using HEMM powders. During the sintering process, $CaTiO_3$, TixOy, and CaO were formed because of the reaction between Ti and CPP. The effects of CPP content on the physical and mechanical properties of the sintered Ti-Nb-Zr-Mo-CPP composites were investigated. The biocompatibility and corrosion resistance of the Ti-Nb-Zr-Mo alloys were improved by the addition of CPP.