• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.613-618
• /
• 2001

For the evaluation of operability of MOV(Motor Operated Valve), the precision prediction of thrust/torque acting on the valve is important. In this paper, the analytical prediction method of thrust/torque was proposed. The design basis stem thrust calculation typically considers the followings: Packing thrust, Stem rejection load, design basis differential pressure load. In general, test results show that temperature, pressure, fluid type, and differential pressure, independently and combination, all have an effect on the friction factor. The prediction results of thrust/torque are well agrement with dynamic test results.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.353-358
• /
• 2004

Tracing the study of the burst test of steam generator tube, few studies have been reported to effect of external pressure acting on secondary-side in service condition. In this study the burst tests of Inconel 690TT were conducted in order to evaluate burst strength characteristics under the effect of external pressure. We obtained the result that the burst strength of Inconel 690TT increased when external pressure increased while both total circumferential elongation and uniform burst elongation were not affected. Also, according to the increased of external pressure, the size of the burst opening became smaller and the tear was getting severe.

• 한국자동차공학회논문집
• /
• 제11권6호
• /
• pp.134-140
• /
• 2003

The film sensor is used for measuring pressure distribution at planar area, especially at a small space or gap. The present paper deals with the development of film type sensors and system for pressure distribution measuring. The developed system is consist of (1)film sensor with 40/sup */40 array, (2)PCI interface card with maximum sampling rate of 100㎐, and (3)software for data processing and real-time display. The contact pressure test of wiper blade and front glass of vehicle was performed with wiper blade by 40cm. Generally spring force of wiper arm is designed at 0.7∼1kN. Test results of total force was 9.4N and 7.1N in each driver and passenger toward. The paper suggested possibility for base definition in wiper design. A windshield wiper blade experiment revealed that the system successfully measured the contact force distribution during static state, showing the usefulness of the developed system.

• Wind and Structures
• /
• 제30권3호
• /
• pp.289-298
• /
• 2020

Gusts generated by downburst have caused a great variety of structural damages in many regions around the world. It is of great significance to accurately evaluate the downburst-induced wind load on high-rise building for the wind resistance design. The main objective of this paper is to propose a computational modeling approach which can satisfactorily predict the mean and fluctuating wind pressure coefficients induced by downburst on high-rise building surfaces. In this study, using an impinging jet to simulate downburst-like wind, and simultaneous pressure measurements are obtained on a high-rise building model at different radial locations. The model test data are used as the database for developing back propagation neural network (BPNN) models. Comparisons between the BPNN prediction results and those from impinging jet test demonstrate that the BPNN-based method can satisfactorily and efficiently predict the downburst-induced wind pressure coefficients on single and overall surfaces of high-rise building at various radial locations.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.629-636
• /
• 2003

The purpose of this study is localization of safety relief valves for Nuclear Service through technical development with overall design, fabrication, inspection, capacity certification test and functional qualification test of safety relief valves in accordance with ASME Section III and KEPIC Code. Safety relief valve is the important equipment used to protect the pressure vessel, the steam generator and the other pressure facility from overpressure by discharging the operating medium when the pressure of system is reaching the design pressure of the system. But we're depending on technology of the other country up to the present time. Because we don‘ have our own technologies, we have been spent the great time and money on installing and repairing safety relief valve at nuclear power plant. Therefore we have to achieve the development of safety relief valves for Nuclear Service with our own technologies.

• Journal of Advanced Marine Engineering and Technology
• /
• 제30권2호
• /
• pp.218-224
• /
• 2006

Experimental results for pressure gradient of HCs refrigerants R-290. R-600a. R-1270 and HCFC refrigerant R-22 during condensing inside horizontal double pipe heat exchangers are presented. The test sections which have the tube inner diameter of 10.98mm. and the tube inner diameter of 8mm are used for this investigation. Hydrocarbon refrigerants have higher pressure drop than R-22 in both test sections with the diameters of 12.70mm and 9.52mm. Pressure drop increased with the increase of the mass flux. These results form the investigation can be used in the design of heat transfer exchanger using hydrocarbons as the refrigerant for the air-conditioning systems

• 한국추진공학회지
• /
• 제14권1호
• /
• pp.48-55
• /
• 2010

본 논문에서는 엔진고공환경 시험설비의 엔진 입구 덕트에서 측정한 전압력과 정압력 및 전온도를 통해 실시간으로 공기유량을 계산하고, 압력프로파일을 이용하여 경계층 레이크를 장착하지 않았을 경우에도 공기유량을 예측할 수 있는 방법을 기술하였다. 또한, 엔진입구배관에 걸친 덕트 연결부를 통한압력손실을 예측하고, 이를 통해 공기유량을 보정함으로써, 고공환경시험설비에서의 공기유량측정의 신뢰도를 향상시키고 설비유지측면에서의 운용성을 보고자 하였다.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2001년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Fall 2001
• /
• pp.98-106
• /
• 2001

The deformation characteristics of cohesionless soils in Korea were investigated using resonant column tests. Total 60 samples, which were sampled from sedimentary and residual soils and reconstituted using controlled particle-size distributions, were prepared. The confining pressure applied in the tests ranges from 20 kPa to 500 kPa. The test results ware categorized into 3 groups including clean sands, silt and silty sand, and residual soils. Based on test results, the small-strain shear modulus(G$_{max}$) and damping ratio(D$_{min}$) were determined and the effects of confinement on G$_{max}$ and D$_{max}$ were characterized. The empirical correlations predicting G$_{max}$ were suggested for 3 group soils. Nonlinear deformational characteristics of clean sands are significantly affected by confining pressure and the ranges and mean curves for G and D are suggested considering the range of confining Pressure. The silt and silty sand and residual soils were weakly affected by confining pressure, so the representative ranges and curves, independent of confining pressure, were proposed.d.posed.d.

• 항공우주기술
• /
• 제6권2호
• /
• pp.29-34
• /
• 2007

본 논문에서는 엔진고공환경 시험설비의 엔진 입구 덕트에서 측정한 전압력과 전온도를를 통해 실시간으로 공기유량을 계산하고, 압력프로파일을 이용하여 경계층 레이크를 장착하지 않았을 경우에도 공기유량을 예측할 수 있는 방법을 기술하였다. 또한, 엔진입구배관에 걸친 덕트 연결부를 통한 압력손실을 예측하고, 이를 통해 공기유량을 보정함으로써, 고공환경시험설비에서의 공기유량측정의 신뢰도를 향상시키고 설비유지측면에서 운용성을 보고자 하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권5호
• /
• pp.609-616
• /
• 1998

Structural analyses are preformed for the high pressure steam turbine casings of the nuclear and the fossil power plants. An axisymmetric boundary element program for analysis of the casings is developed and applied in the process of practical structural design. To show the useful-ness and accuracy of the developed program results of the analysis are compared with those of the finite element analysis under hydrostatic test pressure, To check the validity of the axisymmetric numerical analysis of the casings the stresses resulting from the hydrostatic test pressure are measured using the strain gate. The results of the numerical analyses are compared and discussed with those of the experiments.