• Tribology and Lubricants
• /
• 제16권4호
• /
• pp.247-252
• /
• 2000

As the demand for higher areal recording densities requires a lower flying height of the slider, the variation of the flying height of the slider during drive operation becomes of great concern. The variation of the flying height is closely related with the slider design parameters such as air bearing shape, cavity depth, shallow step depth, crown, camber, pitch offset, roll offset, gram load, and so on. The objective of this work is to optimize the cavity depth and the shallow step depth, which are the control factors in air bearing design, using Robust Design method. It was found that the shallow step depth was statistically significant in affecting the variation of flying height, therefore the level of the shallow step depth should be chosen to minimize the variation of flying height.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.579-584
• /
• 2000

Algebraic Reynolds Stress (ARS) model is applied in order to analyze the turbulent flow of wall-attaching offset jet and to evaluate the model's predictability. The applied numerical schemes are upwind scheme and skew-upwind scheme. The numerical results show good prediction in first order calculations (i.e., reattachment length, mean velocity, pressure), while they show slight deviations in second order (i.e., kinetic energy and turbulence intensity). By comparison with the previous results using $k-{\varepsilon}$ model, ARS model predicts better than the standard $k-{\varepsilon}$ model, however, predicts slightly worse than the $k-{\varepsilon}$ model including the streamline curvature modification. Additionally this study can reconfirm that skew-upwind scheme has approximately 25% improved predictability than upwind scheme.

• 대한기계학회논문집B
• /
• 제24권12호
• /
• pp.1615-1624
• /
• 2000

Algebraic Reynolds Stree (ARS) model is applied in order to analyze the turbulent flow of wall-attaching offset jet and to evaluate the predictability of model. The applied numerical schemes are the upwind scheme and the skew-upwind scheme. The numerical results show a good prediction in the first order calculations(i.e., reattachment length, mean velocity, pressure), however, slight deviations in the second order(i.e., kinetic energy and turbulence intensity). Comparing with the previous results using the k-$\varepsilon$ model, the ARS model predicts better than the standard k-$\varepsilon$ model, however, slightly worse than the k-$\varepsilon$ model including the streamline curvature modification. Additionallay this study can reconfirm that the skew-upwind scheme has approximately 25% improved predictability than the upwind scheme.

• 대한기계학회논문집B
• /
• 제38권8호
• /
• pp.709-714
• /
• 2014

리버스 옵셋 인쇄는 인쇄전자를 위한 미세 패터닝기술 중 하나로서 수 ${\mu}m$ 이하의 선폭을 구현할 수 있다. 옵셋 인쇄의 특성상 잉크는 PDMS 재질의 블랑켓에 전사된 후 음각으로 패턴된 클리쉐에 접촉하여 불필요한 패턴을 제거하게 되는데, 이 때 블랑켓은 압력에 의하여 음각 패턴 내부로 침투하는 변형이 발생한다. 이러한 변형은 인쇄 압력에 비례하며, 과도한 인쇄 압력은 넓은 면적의 패턴을 인쇄할 때 클리쉐 패턴의 바닥에 블랑켓이 닿는 불량을 일으키게 된다. 이 논문에서는 리버스 옵셋 인쇄에서 가압변위에 따른 PDMS 블랑켓의 변형을 유한요소기법을 이용하여 모델링하고 접촉압력 대비 변형량을 예측함으로써 실제 인쇄 장비의 실험 결과와 비교하여 인쇄결함이 발생하지 않도록 하는 클리쉐의 제작조건을 제시하고자 한다.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.2
• /
• pp.215-225
• /
• 2006

Today's requirements for print-press runnability and print quality demand an optimised absorption and adhesion of printing ink on the paper surface. Modern coating concepts for high glossing offset grades use ultra fine pigments, whereas binder level has continuously been decreased to a minimum in recent years to achieve the highest possible sheet gloss development and for economical reasons. Both the ultra fine pigments and the reduced binder levels lead in many cases to a faster ink setting rate. On the other hand, matt paper grades use relatively coarse pigments leading to a slow ink setting compared to the high glossing papers. Both too fast and too slow ink setting properties implicate drawbacks in print quality and print press runnability. The mechanisms behind the interactions between ink and coating have been presented in many previous publications. The purpose of this study was to determine and quantify how the ink setting rate is influenced by pigment system (GCC and GCC/clay blends), latex level and latex properties in the topcoat of double coated sheet fed offset paper. The roles of binder level and type in the precoat were also assessed. The effect of calendering (temperature and pressure) was studied with one formulation. The resulting ink setting characteristics were tested using three different laboratory testing instruments. The correlation amongst the different laboratory testing methods is discussed. The results show that by varying the latex properties, the pigment system and/or latex addition level, the ink tack development of ink applied to a topcoat pigment system can be significantly influenced. It can be slowed down as often desired with ultra fine pigments or speeded up in the case of coarse pigments. There was no visible effect on the ink setting rate by using different binder systems in the precoat..

• 대한전자공학회논문지SD
• /
• 제39권9호
• /
• pp.62-71
• /
• 2002

본 논문에서는 용량형 압력센서의 비선형성 문제를 해결하기 위한 적분형 C-V 변환기를 제안하였다. 이 변환기는 스위치 커패시터 적분기와 스위치 커패시터 차동증폭기로 구성되어 있으며 인가된 압력에 반비례하는 센서용량을 전압으로 변환하여 선형적으로 출력한다. 제안된 적분형 C-V 변환기는 PSPICE 시뮬레이션에서 초기 전극간격의 90%에 해당하는 큰 변위에 대해서 0.01%/FS 이하의 매우 낮은 비선형도와 오프셋 용량 및 기생용량에 둔감한 우수한 특성을 보였다. 또한 센서신호처리의 필수기능인 오프셋 보정 및 이득조정이 적분형 C-V 변환기에서 용이하게 구현됨을 보였다.

• Tribology and Lubricants
• /
• 제37권3호
• /
• pp.99-105
• /
• 2021

In this study, for a high-pressure turbine (HPT) of 800 MW class supercritical thermal-power plant, considering aerodynamic cross-coupling, we performed a rotordynamic logarithmic decrement (LogDec) stability analysis with various tilting pad journal bearing (TPJB) designs, which several steam turbine OEMs (original equipment manufacturers) currently apply in their supercritical and ultra-supercritical HPTs. We considered the following TPJB designs: 6-Pad load on pad (LOP)/load between pad (LBP), 5-Pad LOP/LBP, Hybrid 3-Pad LOP (lower 3-Pad tilting and upper 1-Pad fixed), and 5-Pad LBPs with the design variables of offset and preload. We used the API Level-I method for a LogDec stability analysis. Following results are summarized only in a standpoint of LogDec stability. The Hybrid 3-Pad LOP TPJBs most excellently outperform all the other TPJBs over nearly a full range of cross-coupled stiffness. In a high range of cross-coupled stiffness, both the 6-Pad LOP and 5-Pad LOP TPJBs may be recommended as a practical conservative bearing design approach for enhancing a rotordynamic stability of the HPT. As expected, in a high range of cross-coupled stiffness, the 6-Pad LBP TPJBs exhibit a better performance than the 5-Pad LBP TPJBs. However, contrary to one's expectation, notably, the 5-Pad LOP TPJBs exhibit a slightly better performance than the 6-Pad LOP TPJBs. Furthermore, we do not recommend any TPJB design efforts of either increasing a pad offset from 0.5 or a pad preload from 0 for the HPT in a standpoint of stability.

• 한국소음진동공학회논문집
• /
• 제23권4호
• /
• pp.372-378
• /
• 2013

An acoustical shape optimization problem is formulated for optimal design of a perforated reactive muffler with offset inlet/outlet. The mean transmission loss value in a target frequency range is maximized for an allowed pressure drop value between an inlet and an outlet. Partitions in the chamber are divided into several sub-partitions, whose lengths are selected as design variables. Each sub-partition has the same number of holes, whose sizes are equal. A finite element model is employed for acoustical and flow analyses. A gradient-based optimization algorithm is used to obtain an optimal muffler. The acoustical and fluidic characteristics of the optimal muffler are compared with those of a reference muffler. Validation experiment is carried out to support the effectiveness of our suggested method.

• ETRI Journal
• /
• 제38권4호
• /
• pp.685-694
• /
• 2016

A surface micromachined piezoresistive pressure sensor with a novel internal substrate vacuum cavity was developed. The proposed internal substrate vacuum cavity is formed by selectively etching the silicon substrate under the sensing diaphragm. For the proposed cavity, a new fabrication process including a cavity side-wall formation, dry isotropic cavity etching, and cavity vacuum sealing was developed that is fully CMOS-compatible, low in cost, and reliable. The sensitivity of the fabricated pressure sensors is 2.80 mV/V/bar and 3.46 mV/V/bar for a rectangular and circular diaphragm, respectively, and the linearity is 0.39% and 0.16% for these two diaphragms. The temperature coefficient of the resistances of the polysilicon piezoresistor is 0.003% to 0.005% per degree of Celsius according to the sensor design. The temperature coefficient of the offset voltage at 1 atm is 0.0019 mV and 0.0051 mV per degree of Celsius for a rectangular and circular diaphragm, respectively. The measurement results demonstrate the feasibility of the proposed pressure sensor as a highly sensitive circuit-integrated pressure sensor.

• 대한치과보철학회지
• /
• 제43권1호
• /
• pp.61-77
• /
• 2005

Statement of problem. The implant prosthesis has been utilized in various clinical cases thanks to its increase in scientific effective application. The relevant implant therapy should have the high success rate in osseointegration, and the implant prosthesis should last for a long period of time without failure. Resorption of the peri-implant alveolar bone is the most frequent and serious problem in implant prosthesis. Excessive concentration of stress from the occlusal force and biopressure around the implant has been known to be the main cause of the bone destruction. Therefore, to decide the location and angulation of the implant is one of the major considering factors for the stress around the implant fixture to be dispersed in the limit of bio-capacity of load support for the successful and long-lasting clinical result. Yet, the detailed mechanism of this phenomenon is not well understood. To some extent, this is related to the paucity of basic science research. Purpose. The purpose of this study is to perform the stress analysis of the implant prosthesis in the partially edentulous mandible according to the different nature locations and angulations using three dimensional finite element method. Material and methods, Three 3.75mm standard implants were placed in the area of first and second bicuspids, and first molar in the mandible Thereafter, implant prostheses were fabricated using UCLA abutments. Five experimental groups were designed as follows : 1) straight placement of three implants, 2) 5$^{\circ}$ buccal and lingual angulation of straightly aligned three implants, 3) 10$^{\circ}$ buccal and lingual angulation of straightly aligned three implants. 4) lingual offset placement of three implants, and 5) buccal offset placement of three implants. Average occlusal force with a variation of perpendicular and 30$^{\circ}$ angulation was applied on the buccal cusp of each implant prosthesis, followed by the measurement of alteration and amount of stress on each configurational implant part and peri-implant bio-structures. The results of this study are extracted from the comparison between the distribution of Von mises stress and the maximum Von mises stress using three dimensional finite element stress analysis for each experimental group. Conclusion. The conclusions were as follows : 1. Providing angulations of the fixture did not help in stress dispersion in the restoration of partially edentulous mandible. 2. It is beneficial to place the fixture in a straight vertical direction, since bio-pressure in the peri-implant bone increases when the fixture is implanted in an angle. 3. It is important to select an appropriate prosthodontic material that prevents fractures, since the bio-pressure is concentrated on the prosthodontic structures when the fixture is implanted in an angle. 4. Offset placement of the fixtures is effective in stress dispersion in the restoration of partially edentulous mandible.