• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.140.1-140.1
• /
• 2015

Currently, As Plasma application is expanded to the industrial and medical industrial, Low temperature plasma characteristics became important. Especially in Medical industrial, Low temperature plasma directly adapted to human skin, so their plasma parameter is important. One of the plasma parameters is electron density, some kinds of method to measuring electron density are Thomson scattering spectroscopy and Millimeter-wave transmission measurement. But most methods is expensive to composed of experiment system. Heterodyne interferometer system is cheap and simple to setting up, So we tried to measuring electron density by Laser heterodyne interferometer. To measuring electron density at atmospheric pressure, we need to obtain the phase shift signal. And we use a heterodyne interferometer. Our guiding laser is Helium-Neon laser which generated 632 nm laser. We set up to chopper which can make a laser signal like a pulse. Chopper can make a 4 kHz chopping. We used Needle jet as Ne plasma sources. Interference pattern is changed by refractive index of electron density. As this refractive index change, phase shift was occurred. Electron density is changed from Townsend discharge's electron bombardment, so we observed phenomena and calculated phase shift. Finally, we measured electron density by refractive index and electron density relationship. The calculated electron density value is approximately 1015~1016 cm-3. And we studied electron density value with voltage.

• Journal of Mechanical Science and Technology
• /
• 제17권11호
• /
• pp.1704-1713
• /
• 2003

Point contact film thickness in elastohydrodynamic lubrication (EHL) is analyzed by image processing method for the images from an optical interferometer with monochromatic incident light. Interference between the reflected lights both on half mirror Cr coating of glass disk and on super finished ball makes circular fringes depending on the contact conditions such as sliding velocity, applied load, viscosity-pressure characteristics and viscosity of lubricant under ambient pressure. In this situation the film thickness is regarded as the difference of optical paths between those reflected lights, which make dark and bright fringes with monochromatic incident light. The film thickness is computed by numbering the dark and bright fringe orders and the intensity (gray scale image) in each fringe regime is mapped to the corresponding film thickness. In this work, we developed a measuring technique for EHL film thickness by dividing the image patterns into two typical types under the condition of monochromatic incident light. During the image processing, the captured image is converted into digitally formatted data over the contact area without any loss of the image information of interferogram and it is also interpreted with consistency regardless of the observer's experimental experience. It is expected that the developed image processing method will provide a valuable basis to develop the image processing technique for color fringes, which is generally used for the measurement of relatively thin films in higher resolution.

• 한국정밀공학회지
• /
• 제22권1호
• /
• pp.167-174
• /
• 2005

The design for cold extrusion dies is very important, because the die insert is subjected to very high radial and hoop stresses. The design of cold extrusion dies has many constrained conditions. In this paper, the used assumptions are such that the yield strength of each ring is selected according to the allowable tensile or compressive hoop stress in each ring and the maximum allowable inner pressure, when yielding occurs in one ring of the dies, is obtained by the proposed equation. In order to obtain design variables, such as diameter ratios and interferences, using the maximum inner pressure, the flexible tolerance method was used for shrink-fitted thick-walled cylinders. ANSYS APDL was used to perform the repeated analysis of deformation of the dies due to the variation of the design variables. The response surface methodology is utilized to analyze the relationship between the design variables and the maximum radial displacement of the die insert during extrusion. From the results, it is found that outer diameter of the die insert has the largest effect on the minimization of maximum radial displacement at the inner surface of the dies.

• 한국소음진동공학회논문집
• /
• 제21권11호
• /
• pp.1029-1035
• /
• 2011

Pressure pulsation of exciting sources that generally occurs on the piping system connected to the discharge of BFP(boiler feed water pump) in power plants causes wave reflection, wave interference, resonance, standing wave and so on. But if the operating speed of the pump is changed, the state of the noise and vibration can be done because characteristics of the exciting source are changed. This paper is to investigate the cause of the noise and vibration occurring on the piping system when the operating speed of BFP is down in accordance with lowering of the power generation. It is approached to two points of view ; Firstly, it is examined whether the pulsation source impacts on the shell mode vibration that vibrates radially across the cross-section of the pipe. But it doesn't affect the shell mode as much as the resonance occurs. Secondly, to find the relation between the pulsation source and the acoustic mode of the piping system, analysis for the piping system by indirect BEM(boundary element method) is carried out. Therefore it is investigated that the mechanism of the noise and vibration relates with acoustic mode of the piping system.

• Journal of Pharmaceutical Investigation
• /
• 제9권3호
• /
• pp.27-38
• /
• 1979

This study was attempted to investigate the pharmacological action, especially depressor action of Phellodendri cortex and to elucidate the mechanism of its action, making use of Phellodendri cortex methanol extract (PCME) because its hypotensive action is not clear. Influence of PCME on the blood pressure of the rabbits and cats were observed in this study. PCME, when given intravenously in the rabbits and cats, elicited the hypotensive action, but intraventricular PCME in the rabbits did not show depressor action. Accumulation and tachyphylaxis by PCME administered into the ear-vein of the rabbits were not shown. Depressor effect of PCME in the rabbits was attenuated significantly by pretreatment with phentolamine, guanethidine, chorisondamine and atropine, but not by propranolol, diphenhydramine, cyproheptadine and vagotomization. The pressor activity of angiotensin was unimpaired after injection of maximal hypotensive doses (100mg/kg) of PCME, but the pressor activity of norepinephrine and carotid occlusion was abolished markedly. In addition, PCME given into jugular vein of the cats weakened norepinephrine pressor responses and caused the reversal of epinephrine pressor responses. These results suggest that the hypotensive action of PCME may be due to dual mechanisms by interference with peripheral sympathetic function, alpha adrenoceptor blocking action, and peripheral parasympathomimetics action, muscarinic action.

• 한국압력기기공학회 논문집
• /
• 제10권1호
• /
• pp.7-14
• /
• 2014

There has been extensive experience associated with the operation of SGs wherein it was believed, based on NDE, that throughwall tube indications were present within the tubesheet. The installation of the SG tubes usually involves the development of a short interference fit, referred to as the tack expansion, at the bottom of the tubesheet. The tack expansion was usually effected by a hard rolling process and thereafter, in most instance, by the expansion of a urethane plug inserted into the tube end and compressed in the axial direction. The rolling process by its very nature is considered to be intensive with regard to metalworking at the inside surface of the tube and would be expected to lead to higher residual surface stresses. Alternate repair criteria(ARC) in the tack expansion area have been developed and applied to nuclear power plants in USA, however domestic nuclear power plants have not applied ARC for tubes in tubeheet area yet. In consideration of the degradation characteristics of tubes in the Steam Generator tubesheet, this paper suggests ARC application for tubes in the steam generator tubesheet of the domestic nuclear power plants in order to assure life time of the steam generator as well as nuclear power plants.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제26회 춘계학술대회논문집
• /
• pp.306-309
• /
• 2006

슬롯을 이용한 충격파와 난류 경계층의 간섭유동의 피동제어에 관한 연구가 이루어졌다. 슬롯의 다양한 형상 변화가 간섭유동에 미치는 영향이 관찰되었으며, 이를 위하여 간섭유동 후방에서 피토/벽압력 분포 및 쉴리렌, 오일막 간섭 줄무늬 형상과 같은 유동가시화 정보 등이 얻어졌다. 특정한 슬롯적용의 경우, 충격파를 통한 전압손실의 감소가 관찰되었으나 경계층의 두께는 두꺼워지는 것으로 나타났다.

• 한국산학기술학회논문지
• /
• 제13권6호
• /
• pp.2428-2434
• /
• 2012

본 논문은 제동 시스템에서 전자식 주행안정 제어장치(ESC)의 유압 모듈레이터의 솔레노이드 밸브 제어에 대한 것이다. ESC의 전자제어유니트(ECU)를 제어하기 위한 방법으로 고주파수 제어와 슬로프 제어를 적용하였으며, 서지 압력 및 전자파간섭(EMI) 저감 특성을 연구하였다. 고주파수에서의 전자파 방출을 줄이기 위하여 ECU 출력 단에 슬로프 제어 기능을 추가하였다. 측정결과 제동 시스템에서 고주파수 ECU의 솔레노이드 밸브제어 방법에 따라 서지 압력과 전자파 방출이 저감될 수 있음을 확인하였다. 결론적으로 고주파수 ECU 제어 연구 결과에 의해 제동 시스템 성능을 향상방안을 제시하고자 한다.

• 항공우주기술
• /
• 제3권2호
• /
• pp.72-80
• /
• 2004

터보펌프를 구성하는 부분 조합체 중의 하나인 산화제 펌프의 인듀서와 임펠러에 대해서 정적 구조해석을 수행하였다. 먼저 온도, 원심력 및 압력의 영향을 각각 독립적으로 파악한 후 조합된 하중이 작용하는 경우에 대해서 인듀서와 임펠러의 거동을 살펴보았다. 설계된 형상과 재질에 대해서 구조적으로 가장 큰 영향을 미치는 요소는 온도였으며, 모든 경우에 대해서 적절한 안전 여유를 갖는 것으로 예측되었다. 하지만 진동의 영향은 고려되지 않았기 때문에 회전부와 케이싱과의 간섭 여부를 정확히 파악하기 위해서는 추가적으로 진동 해석이 수행되어야 할 것이다.

• 대한조선학회논문집
• /
• 제47권4호
• /
• pp.589-597
• /
• 2010

The indoor noise of the naval vessel is very important considering hearing protection, improvement of working environment and easily communication between crews. When the environment of the naval vessel suffering from the noise is considered, it is very important to be quiet in the living area where the crews have a rest sufficiently. In addition, the noise of the working area should be reduced in order to increase working efficiency. Therefore, in this research, the satisfactions about the indoor noise are survey for crews working in a naval vessel. Through this survey, the relationship between the indoor noise and crew's satisfaction about it can be found. As a result, the limit of sound pressure level which almost all crew can be satisfied with the indoor noise about their living and working area is suggested base on the survey in this research.