• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.4
• /
• pp.484-490
• /
• 2012

In this paper, we design a digitally pre-distorted RF power amplifier operating in 900 MHz band. The linearity of RF power amplifier is improved by employing the digital pre-distortion(DPD) based on affine projection(AP) algorithm, where the look-up table(LUT) method is used with non-linear indexing. The proposed DPD with AP algorithm is compared with that with normalized least mean square(NLMS) algorithm, applied to the RF power amplifier. A commercial power amplifier module is used for verification of the proposed algorithm which shows improvement of adjacent channel leakage ratio(ACLR) by about 21 dB.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.1A
• /
• pp.11-15
• /
• 2006

A pre-amplified semiconductor optical amplifier-Mach-Zehnder interferometer(SOA-MZI) wavelength converter (WC) using a continuous wave-holding beam(CW-HB) is proposed and experimentally demonstrated at 10Gb/s. The proposed scheme achieves not only enhancement of input power dynamic range(IPDR) to over 20dB but also higher Q parameter of about 2 to 3 by no output signal distortion and higher extinction ratio(ER) of about 2dB to 5dB by low noise figure (NF), compared with the bias current control method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.12
• /
• pp.1303-1312
• /
• 2008

Satellite WiBro system has high PAPR characteristics in addition to the nonlinear characteristics of the power amplifier. These characteristics reduce amplifying efficiency of the power amplifier and also cause high error rate and interference with adjacent channels. This paper proposed satellite WiBro based system to reduce input signal's IBO of TWTA remarkably by adapting simultaneously PAPR reduction techniques, active-constellation extension technique and pre-distortion technique.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.12
• /
• pp.1069-1074
• /
• 2016

This paper presents a V-band two-stage power amplifier integrated circuit using TSMC 65 nm CMOS process. The simple input, output, and inter-stage matching networks based on passive components are integrated. By compensating for power gain characteristics using a pre-distortion technique, the linearity of the power amplifier was improved. The implemented two-stage power amplifier showed a power gain of 10.4 dB, a saturated output power of 9.7 dBm, and an efficiency of 20.8 % with a supply voltage of 1 V at the frequency band of 58.8 GHz.

• Journal of Korea Multimedia Society
• /
• v.21 no.9
• /
• pp.1068-1075
• /
• 2018

We propose a method for driving loudspeakers from class D audio power amplifiers in current mode, instead of in conventional voltage mode, which was impossible with the feedback circuitry. Unlike analog audio amplifiers, Class D audio power amplifiers have signal delay between the input and output signals, which makes it difficult to apply the feedback circuitry for current-mode driving. The idea of the pre-distortion scheme used for the compensation of the non-linearity of RF power amplifiers is adapted to remedy the impedance variation effect of the loudspeakers for current driving. The method uses the speaker model for the pre-distorter to compensate for the speaker impedance variation with frequency. The simulation and test results confirms the validity of the proposed method.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.681-684
• /
• 2015

Power amplifier is an essential component for transmitting signals to a remote receiver in wireless communication systems. Power amplifier is a non-linear device in general, and the nonlinear distortion becomes severer as the output power increases. The nonlinearity results in spectral regrowth, which leads to adjacent channel interference, and decreases the transmit signal quality. To linearize power amplifiers, many techniques have been developed so far. Among the techniques, digital pre-distortion is known as the most cost and performance effective technique. However, the linearization performance falls down abruptly when the power amplifier operates in its saturation region. This is because of the severe nonlinearity. To relieve this problem, this paper proposes a new adaptive predistortion technique. The proposed technique controls the adaptive algorithm based on the power amplifier input level. Specifically, for small signals, the adaptive predistortion algorithm works normally. On the contrary, for large signals, the adaptive algorithm stops until small signals occur again. By doing this, wrong coefficient update by severe nonlinearity can be avoided. Computer simulation results show that the proposed method can improve the linearization performance compared with the conventional digital predistortion algorithms.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.49 no.1
• /
• pp.80-87
• /
• 2012

We have developed the ATE(Automatic Test Equipment) system for the performance test of pre-amplifier of thermal imaging devices. The device regenerates the electronic signals of photon detection module which is normally in weak energy, for the image signals processing. Previous ATE system was primarily and actively developed in the field of semiconductor devices quality parts inspection. Recently, it has been studied in the field of performance testing of equipment. In the field of thermal performance test equipment, however, it lacks the study of ATE compared to other areas, which causes the maintenance related to the core of military thermal imaging system maintenance to be limited. In this paper, a new study of ATE in the field of thermal imaging system is done. It is designed to be used universally for the ATE system with different types of circuit card of thermal imaging system by adopting matrix relays. Using the developed ATE measuring the pre-amplifier amplitude, an average amplified amplitude of 2.71Vpp was measured which confirms that it is within the range of theoretical analysis and also verifies the good performance of the developed ATE.

• Journal of Advanced Navigation Technology
• /
• v.23 no.2
• /
• pp.179-185
• /
• 2019

In this paper, we have studied narrow-band analog pre-distortion linearization technique using UHF 400 MHz band 20 W power amplifier. The analog pre-distorter used the SC1894 radio frequency power amplifier linearizer(RFPAL) provided by MAXIM Corp and through the look-up table technique confirmed the intermodulation distortion(IMD) performance and the adjusted channel leakage ratio(ACLR) improvement for bandwidth below 1 MHz which does not operate on existing chips. In the 400 MHz (400 ~ 500 MHz) band, IMD performance and the ACLR improvement of up to 17.46 dB based on 1-channel offset and up to 16.6 dB based on 2-channel offset were confirmed. In the system requiring the same linearity, we confirmed power efficiency improvement of 12.41% at output power of over 40 W.

• Journal of electromagnetic engineering and science
• /
• v.11 no.1
• /
• pp.16-26
• /
• 2011

This paper presents high power and high efficiency Doherty amplifiers for 2.345 GHz wireless broadband (WiBro) applications that use a Nitronex 125-W ($P_{3dB}$) GaN high electron mobility transistor (HEMT). Two- and three-way Doherty amplifiers and a saturated Doherty amplifier using Class-F circuitry are implemented. The measured result for a center frequency of 2.345 GHz shows that the two-way Doherty amplifier attains a high $P_{3dB}$ of 51.5 dBm, a gain of 12.5 dB, and a power-added efficiency (PAE) improvement of about 16 % compared to a single class AB amplifier at 6-dB back-off power region from $P_{3dB}$. For a WiBro OFDMA signal, the Doherty amplifier provides an adjacent channel leakage ratio (ACLR) at 4.77 MHz offset that is -33 dBc at an output power of 42 dBm, which is a 9.5 dB back-off power region from $P_{3dB}$. By employing a digital pre-distortion (DPD) technique, the ACLR of the Doherty amplifier is improved from -33 dBc to -48 dBc. The measured result for the same frequency shows that the three-way Doherty amplifier, which has a $P_{3dB}$ of 53.16 dBm and a gain of 10.3 dB, and the saturated Doherty amplifier, which has a $P_{3dB}$ of 51.1 dBm and a gain of 10.3 dB, provide a PAE improvement of 11 % at the 9-dB back-off power region and 7.5 % at the 6-dB back-off region, respectively, compared to the two-way Doherty amplifier.

• Proceedings of the KAIS Fall Conference
• /
• 2010.11a
• /
• pp.76-79
• /
• 2010

본 논문에서는 고 효율 및 고 출력 특성을 가지는 질화갈륨(GaN) 소자를 이용하여 WiMAX 및 LTE System에 사용될 수 있는 DPD용 Pallet Amplifier를 제작하였다. 제작된 Pallet Amplifier는 Pre-drive로써 저 전류의 MMIC를 채택하고, Drive 단과 Main 단에 15W 급과 30W 급의 질화갈륨 소자를 사용 하였으며, 추가적인 효율 개선을 위해 PCB상에 Doherty Structure를 적용함으로써 보다 높은 효율을 구현하였다. 제작된 Pallet Amplifier는 음 전원 Bias 제어 회로, 온도에 따른 Gain 보상회로, Sequence 회로 및 Main 전원 Drop에 따른 보호 회로를 구현하였다. WiMAX Signal을 이용한 Modulation Power 10Watt Test에서 약 36.8~38.3%의 Pallet 효율과 DPD Solution인 TI GC5325SEK DPD Board 사용 시 ACLR은 약 46dBc 이상을 가지는 것으로 측정되었다. 본 논문에서 제작된 Pallet Amplifier는 Upper Band와 Lower Band로 나누어 제작되었던 기존 Pallet Amplifier와 달리 하나의 Pallet Amplifier로 2496~2690MHz에서 모두 사용하면서 종전에 사용되고 있는 Pallet Amplifier에 비해 Size가 최소 10% 이상 축소되어 효율 및 크기 면에서 종전 Pallet Amplifier보다 큰 이점을 갖는다.