• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.1316-1318
• /
• 2002

A methodology for reliability and economic analysis of wind embedded electric power system is presented in this paper. This is done by evaluating the reliability index, loss of load expectation (LOLE), for the power system with and without integration of wind system in the overall electric power system. Economic analysis of the wind energy embedded electric system is done in terms of conventional fuel saving assessment due to the use of wind power generation units.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.86-88
• /
• 2003

The efficiency of electric machine is important due to increase of interest about energy saving. Single Phase Line Start Permanent Magnet Synchronous Motor has high efficiency and power factor. LSPMSM offer a high efficiency as compared induction motor which are used in the home appliance. The analysis and design of LSPMSM is difficult because of unbalanced rotating magnetic field, nonlinear characteristics and rotor saliency. To consider these effects, F.E.M(Finite Element Methods) is coupled equivalent circuit methods. In this paper, a methods of analysis and design using F.E.M and equivalent circuit is represented.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.51-54
• /
• 2005

Generator efficiency optimization is important for economic saving and environmental pollution reduction. In general, the machine loss can be reduced by the decreasing the flux level, resulting in the significant reduction of the core loss. This paper proposesan model-based controller is used to decrement the excitation current component on the basis of measured stator current and machine parameters and the q-axis current component controls the generator torque, by which the speed of the induction generator iscontrolled according to the variation of the wind speed in order to produce the maximum output power. The generator reference speed is adjusted according to the optimum tip-speed ratio. The generated power flows into the utility grid through the back-to-back PWM converter. The grid-side converter controls the dc link voltage and the line-side power factor by the q-axis and the d-axis current control, respectively. Experimental results are shown to verify the validity of the proposed scheme.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1350-1354
• /
• 2007

As the importance of low power design is emphasized, power consumption became one of the standards that represent the performance of the system. The purpose of this study is to decide design variable that minimize power consumption for the oxygen concentrator in two bed-one compressor 8 step PSA process that has above 90% purity at 3lpm by using given constants and selected parameters. Setting selected parameters as cycle time and equalization time, optimization for PSA process in the oxygen concentrator is progressed. For this, we need to know the features and basic principals of PSA process and to deduce objective function of performance analysis. Validations for objective function and lots of experiments are needed too. By using the characteristic curve of the compressor and the pressure curve of the process for 1 cycle, objective function was set. After theoretical 2 dimensional optimized paths was obtained. And then, by experiment, theoretical optimized path was verified.

• Journal of information and communication convergence engineering
• /
• v.7 no.1
• /
• pp.52-56
• /
• 2009

In this research, we have studied the development of dc-dc converter suitable for the driving of mobile instruments by using a dye-sensitized solar cell(DSC). We also have designed a interlocking circuit. The circuit makes power generation be saved in one battery and concurrently be discharged in the other battery. As this application, mobile devices such as MP3, cellular phone are operated by using power generator from DSC during the daytime and they can be operated by using the saving energy of the daytime during the night. Consequently, it has a simple and robust circuit configuration. Besides, we designed dc-dc converter circuit to drive low power instruments by using NMOS switch and PMOS rectifier. Operational modes are analysed, and then validity of the proposed interface circuit is verified through DCS.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.1034-1037
• /
• 2002

A switched-capacitor(SC) type DC-DC converter having capability of integrated circuit fabrication have been marked for the application of mobile equipments. Especially, a ring type SC power supply is featured by the flexible and dynamic voltage conversion ratio change. In this paper, an improvement of the gate driving techniques is proposed for high power efficiency and less area occupation on the chip. Furthermore, its power-saving operation in the stand-by state is proposed. The three-capacitors ring type power supply is really designed and discussed. As results, the simulation results shows the high efficiency of 92.1%, and the higher output put voltage of 10.5 V compared with conventional one of 8.6 V.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.34C no.5
• /
• pp.1-17
• /
• 1997

With the increasing performance and density of VLSI scircuits as well as the popularity of portable devices such as personal digital assitance, power consumption has emerged as an important issue in the design of electronic systems. Low power design techniqeus have been pursued at all design levels. However, it is more effective to attempt to reduce power dissipation at higher levels of abstraction which allow wider view. In this paper, we propose a simultaneous scheduling and binding scheme which increases the correlation between cosecutive inputs to an operation so that the switched capacitance of execution units is reduced in datapath-dominated circuits. The proposed method is implemented and integrated into the scheduling and assignment part of HYPER synthesis environment. Compared with original HYPER synthesis system, average power saving of 23.0% in execution units and 14.2% in the whole circuits, ar eobtained for a set of benchmark examples.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.1
• /
• pp.46-52
• /
• 2013

Economic properties of an integrated wind power plant (WPP) and the demand response (DR) programs in the sample electricity market are studied. Time of use (TOU) and direct load control (DLC) are two of the DR programs that are applied in the system. The influences of these methods and the incentive payments by market operator's (MOs) with variable elasticity are studied. It is observed that DR with TOU and DLC programs together yields better revenue and energy saving for MOs.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.402-407
• /
• 2003

The main reason to select the maxium plant efficiency through the performance test in fossil power plant is to increase the efficiency of power plant as well as saving energy collated with the policy of government. This study is aimed at unerstanding the variantion trend of efficiency and analyzing the efficiency of boiler and turbine through each of the performance test. Ultimately, the maxium efficiency of power plant will be presented in super-critical pressure type power plant.

• Proceedings of the KIPE Conference
• /
• 2018.07a
• /
• pp.424-425
• /
• 2018

In the introduction, this paper introduces LS Industrial Systems' medium-voltage drive installed at Hyundai Green Power, an 800MW gas power plant. In the body, it explains the synchronous transfer technology and new speed search technology applied to Forced Draft(FD) Fan and Boiler Feed-water(BF) Pump, which are power generation facilities. Lastly, it shows the annual energy saving amount and operation status which are applied to each facility and proves that it is a successful application case.