• Journal of Digital Convergence
• /
• v.12 no.4
• /
• pp.343-348
• /
• 2014

This paper suggested a theoretical approach and an implementation for the design of an unequal Wilkinson power divider with a high dividing ratio operating at two-frequencies. The T-section transmission lines and the two-section of Monzon's theory are proposed to operate a dual-band application. To achieve the high dividing ratio divider, the high impedance line using a T-shaped structure and low impedance lines with periodic shunt open stubs are implemented. For the validation of this divider, a dual-band power divider with a high dividing ratio of 5 is simulated and measured at 1 GHz and 2 GHz. The measured performances of the divider are in good agreements with simulation results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.4
• /
• pp.499-508
• /
• 1993

This paper has dealt with the design methods and the analysis of frequency characteristics for the power splitters with ferrite toroids, which are extensively used in CATV and/or MATV systems. The theoretical design methods and frequency characteristics of the prototype Wilkinson's 2-way power divider have been reviewed in lumped-element circuits form. On the basis of the design theory of the prototype Wilkinson's power divider, the method compensating of the prototype Wilkinson's power divider has been proposed by means of adding matching transformers. Thus, it has been shown that the theoretical frequency characteristics of the compensated power splitter are improved drastically in comparison with the prototype Wilkinson's power divider. Furthermore, the practical measurements of the frequency characteristics for the fabricated circuits show agreements with the theoretical results, and hence, the validity of the proposed design and analysis methods has been confirmed.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.406-411
• /
• 2005

In this paper, we propose an active 90$^{\circ}$ phase divider for application to MMIC. Because of their very large size, conventional passive 90$^{\circ}$ dividers can't be integrated on MMIC. Therefore, highly miniaturized 90$^{\circ}$ dividers are required for a development of highly integrated MMIC. For this reason, active 90$^{\circ}$ divider is indispensable because active phase divider is much smaller than conventional passive dividers, and it can be integrated on MMIC. In this work, we developed active 90$^{\circ}$ divider with emitter inductor, and it was employed for the operation of the balanced mixer in order to verify the performance of the active 90$^{\circ}$ divider. According to the results, it was found that the active 90$^{\circ}$ divider exhibited good RF performances comparable to conventional passive power dividers.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.1
• /
• pp.46-50
• /
• 2013

A modified design that can reject the nth harmonic components in the Wilkinson power divider is presented. After adding transmission lines of electrical lengths determined by suppression terms between two transformers of the traditional design, a solution of the modified Wilkinson divider can be found. Experimental results show the second and third harmonic suppression to be -45.3 dB and -46.4 dB, respectively, while maintaining the conventional performance at the fundamental frequency.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.7
• /
• pp.102-108
• /
• 1998

A new 1*4 optical waveguide power divider is proposed and fabricated. It consists of a 1*4 multi-branch structure with a beam separator and two beam expanders that can control the splitting ratios between the output ports. The proposed optical waveguide power divider is designed by employing the two dimensional finite difference beam propagation method and is fabricated by a reactive ion etching method. The splitting ratio of fabricatd device is 25.0 : 25.7 : 25.3 : 24.0 for TE mode and 25.7 : 25.2 : 24.1 : 25.0 for TM mode. Comapred with the conventional Y-branch structure, the proposed structure shortens the length of a 1*N divider by the factor 3. Thus it reduces the total propagation loss and the total radiation loss at the branch points. furthermore, the splitting ratios between the output ports may be controlled in this structure for some special applications.

• Journal of Advanced Navigation Technology
• /
• v.25 no.3
• /
• pp.229-235
• /
• 2021

This paper proposes a method of implementing an unequal power divider for high splitting ratios by using transmission lines connected with open and short stubs. The proposed method is an equivalent circuit analysis of a transmission line with an additional port so that it can be converted to an arbitrary impedance in the center of a 2-port transmission line and a 3-port transmission line with an open or short stub connected in parallel to each port. To prove the validity of this method, a Wilkinson power divider with k² = 20 dB splitting ratio and a Gysel power divider with k² = 17 dB splitting ratio were designed at a center frequency of 1 GHz using a 3-port transmission line equivalent circuit. The experimental results of the electrical characteristics are in good agreement with the simulation.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2000.11a
• /
• pp.419-427
• /
• 2000

The 4 by 4 microstrip phased array antenna designed and radiation characteristics are studied. The design frequency was chosen to be 5.8GHz. Chebyshev ratio was achieved by unequal power divider and Wilkinson power divider. The ratio of current at each port is 1 : 2.6 : 2.6 : 1 and then side lobe level is less than -30 dB. It is shown that the radiation beam direction can be changed up to 30。 by control the phase at each port. The result can be used to design electrically controllable microwave scanning antennas.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.417-426
• /
• 2010

This paper describes the 6-way power divider to be used as a feeding structure of the waveguide array antenna generating the plane wave at the near distance. The SMA connector has been connected at the center of the power divider in order to feed the radiating element. The six output ports made of waveguide are positioned on the peripheral of the divider. This paper proposes the method utilizing the inductive post in order to decrease the return loss. The height of the feeding pin, the diameter of the inductive post, and the distance between the feeding pin and inductive post have been investigated, and as a result, the power divider has been optimized. The simulated and measured results show the low return loss of about -40 dB. The calculated and measured transmission coefficients are -7.78 dB and -8.06 dB, respectively. The output power of the six waveguide port show equal-amplitude and equal-phase distribution. Since the power divider proposed in this paper can be expanded to the divider having several output ports, it could be easily applied to the various array antennas.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.7 no.4
• /
• pp.281-286
• /
• 2007

In this paper, sub-circuits for 24 GHz phase locked 100ps(PLLs) using $0.5{\mu}m$ SiGe HBT are presented. They are 24 Ghz voltage controlled oscillator(VCO), 24 GHz to 12 GHz regenerative frequency divider(RFD) and 12 GHz to 1.5 GHz static frequency divider. $0.5{\mu}m$ SiGe HBT technology, which offers transistors with 90 GHz fMAX and 3 aluminum metal layers, is employed. The 24 GHz VCO employed series feedback topology for high frequency operation and showed -1.8 to -3.8 dBm output power within tuning range from 23.2 GHz to 26 GHz. The 24 GHz to 12 GHz RFD, based on Gilbert cell mixer, showed 1.2 GHz bandwidth around 24 GHz under 2 dBm input and consumes 44 mA from 3 V power supply including I/O buffers for measurement. ECL based static divider operated up to 12.5 GHz while generating divide by 8 output frequency. The static divider drains 22 mA from 3 V power supply.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1155-1157
• /
• 2011

본 논문에서는 가전기기의 대기전력 저감을 위해 Capacitive Divider Power Supply(CDPS)로 전원을 공급받는 고효율 전원제어회로를 제안하였다. 이 제어회로는 220 V의 AC 전압을 높은 효율로 기기의 구동용 저전압 DC로 변환하기 위하여 기존의 변압기나 SMPS를 사용하는 대신 커패시터 분압기(Capacitive Divider)를 사용하여 전원을 공급하도록 제작되었으며, 대기 상태에서 교류전력선과 가전기기를 완전히 분리시킨 상태에서 적외선 수신기, MCU, 래치 타입 릴레이 등의 소자를 이용하여 기존 상용 리모컨으로도 전원제어가 가능하도록 설계되었다. 설계된 회로의 소비전력은 2.2 mW이며 본 논문에서 제안한 전원제어회로를 대기전력이 700 mW인 모니터에 적용하여 측정한 결과 대기전력이 7 mW로 낮아지는 것을 확인하였으며, 태양전지를 보조전원으로 추가 할 경우 태양전지에서 공급해주는 전력만큼 대기전력이 감소함을 확인하였다.