• Bulletin of the Society of Naval Architects of Korea
• /
• v.26 no.3
• /
• pp.51-61
• /
• 1989

Recently, the growth in the propulsion power and propeller size of typical energy saving ships has resulted in severe damages of the oil-lubricated stern tube bearing. Consequently, a more rational analytical method for the design of the shafting system is required. In this paper an analytical method applicable to the design of the oil-lubricated stern tube bearing and shafting system is presented. The method consists of the finite element analysis of the shafting system and the oil film hydrodynamics. The shafting system is modeled as a three-dimensional problem using beam elements taking account for the steady components of thrust, lateral forces and moments of the propeller as well as the elastic foundation effects. The oil film hydrodynamics is modeled as a two-dimensional problem. Equal and retangular elements employing hourglass control method are used for the construction of the oil film fluidity matrix. To search the quasi-static equilibrium position between the propeller shaft and the oil film, an optimization technique is employed. Some numerical results based on the proposed method are compared with some measured and numerical data available. They show acceptable agreements with the data.

• Journal of the Microelectronics and Packaging Society
• /
• v.9 no.3
• /
• pp.19-23
• /
• 2002

This paper presents a micro fluxgate magnetic sensor in printed circuit board (PCB). In order to observe the effect of the closed magnetic path, the magnetic cores of rectangular-ring and two bars were each fabricated. Each fluxgate sensor consists of five PCB stack layers including one layer magnetic core and four layers of excitation and pick-up coils. The center layer as a magnetic core is made of a Co-based amorphous magnetic ribbon with extremely high DC permeability of ~100,000. Four outer layers as an excitation and pick-up coils have a planar solenoid and are made of copper foil. In case of the fluxgate sensor having the rectangular-ring shaped core, excellent linear response over the range of -100 $\mu$T to ＋ 100 $\mu$T is obtained with 540 V/Tsensitivity at excitation square wave of 3 $V_{p-p}$ and 360 KHz. The chip size of the fabricated sensing element is $7.3 \times 5.7\textrm{mm}^2$. The very low power consumption of ~8 mW was measured. This magnetic sensor is very useful for various applications such as: portable navigation systems, telematics, VR game and so on.n.

• Journal of Arbitration Studies
• /
• v.28 no.2
• /
• pp.111-135
• /
• 2018

As the disputes in the investment and civil/commercial sectors of China and Taiwan have increased due to active cross-strait economic exchanges, the Chinese government is addressing cross-strait disputes through various dispute resolution methods. In recent years, the Arbitration Center Across the Straits (ACAS) has been established to resolve disputes between cross-strait parties, while ACAS Arbitration Rules have been enacted and enforced. ACAS Arbitration Rules are prepared by referring to the Arbitration Act of China and Taiwan, the relevant provisions and practices of the China International Economic and Trade Arbitration Commission (CIETAC) Arbitration Rules and the cross-strait practical affairs of the China International Economic and Trade Arbitration Commission, and the cross-strait practical affairs giving consideration to the specificity of the cross-strait relationship and the characteristics of economic and trade disputes. Therefore, this paper has compared the features and main contents of the ACAS Arbitration Rules with those of the CIETAC Arbitration Rules. This refers to arbitration proceedings such as form and effect of arbitration agreement, decision of place of arbitration, and organization of arbitral tribunal; the provision of consolidation of multiple contracts and arbitration, and the provision of joinder of arbitration parties, which are implementing the "principle of party autonomy" with streamlining arbitration proceedings and reducing costs; "common, simple, and small sum arbitration proceedings which require shorter arbitration proceedings depending on the size of the arbitration object; and regulations on the "interconnection of mediation and conciliation" which is characteristic of China's arbitration system. Based on the above-mentioned main contents of the ACAS Arbitration Rules in China, there are some implications to be considered in the establishment of the Arbitration Rules of the South-North Commercial Arbitration Commission which will be applied to solve commercial and investment disputes arising from the Inter-Korean Economic Cooperation process, suggesting implications such as the need for the rapid composition and operation of the South-North Commercial Arbitration Commission, requirements for selecting arbitrators, expansion of the object of arbitration, specification of concreteness in deciding the place of arbitration, need to create a variety of arbitration proceedings, and application plan of the International Center for Settlement of Investment Dispute (ICSID) or Third Power Arbitration Agency.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.4
• /
• pp.164-167
• /
• 2010

Bulk GaN single crystal with 1.5 mm thickness was successfully grown by hydride vapor phase epitaxy (HVPE) technique. Free-standing GaN substrates of $10{\times}10,\;15{\times}15$ mm size were fabricate after lift-off of sapphire substrate and their optical properties were characterized properties for device applications. X-ray diffraction patterns showed (002) and (004) peak, and the FWHM of the X-ray rocking curve (XRC) measurement in (002) was 98 arcsec. A sharp photoluminescence spectrum at 363 nm was observed and defect spectrum at visible range was not detected. The hexagonal-shaped etch-pits are formed on the GaN surface in $200^{\circ}C\;H_3PO_4$ at 5 minutes. The defect density calculated from observed etch-pits on surface was around $5{\times}10^6/cm^2$. This indicates that the fabricated GaN substrates can be used for applications in the field of optodevice, and high power electronics.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.6
• /
• pp.67-76
• /
• 2005

This paper proposes a compact-sized surface myoelectric sensor for the myoelectric hand prosthesis. To fit the surface myoelectric sensor in the socket for the myoelectric hand prosthesis, the sensor should be a compact size. The surface myoelectric sensor is. composed of a skin interface and a single processing circuit that are mounted on a single package. The skin interface has one reference and two input electrodes, and the reference electrode is located in the center of two input electrodes. In this paper we propose two types of sensors with the circle- and bar-shaped reference electrode, but all input electrodes are the bar-shaped. The metal material of the electrodes is the stainless steel (SUS440) that endures sweat and wet conditions. Considering the conduction velocity and the median frequency of the myoelectric signal, we select the inter-electrode distance (IED) between two input electrodes as 18mm, 20mm, and 22 mm. The signal processing circuit consists of a differential amplifier with a band pass filter, a band rejection filter for rejecting 60Hz power-line noise, amplifiers, and a mean absolute value circuit. We evaluate the proposed sensor from the output characteristics according to the IED and the shape of the reference electrode. From the experimental results we show the surface myoelectric sensor with the 18mm IED and the bar-shaped reference electrode is suitable for the myoelectric hand prosthesis.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.6
• /
• pp.1019-1026
• /
• 2017

The structural properties of $HfO_2$ films could be improved by calibrating the working pressure owing to the enhanced quality of a thin film. We deposited $HfO_2$ films on glass substrates by radio frequency (RF) magnetron sputtering under a base vacuum pressure lower than $4.5{\times}10^{-6}Pa$, RF power of 100 W, substrate temperature of $300^{\circ}C$. The working pressures were varied from 1 mTorr to 15 mTorr. Subsequently, their structural and optical properties were investigated. In particular, the $HfO_2$ film deposited at 1 mTorr had superior properties than the others, with a crystallite size of 10.27 nm, surface roughness of 1.173 nm, refractive index of 2.0937 at 550 nm, and 84.85 % transmittance at 550 nm. These results indicate that the $HfO_2$ film deposited at 1 mTorr is suitable for application in transparent electric devices.

• Journal of the Korean Electrochemical Society
• /
• v.7 no.2
• /
• pp.94-99
• /
• 2004

Anode-supported flat tubular solid oxide fuel cell (SOFC) was investigated to increase the cell power density. The anode-supported flat tube was fabricated by extrusion process. The porosity and pore size of Ni/YSZ ($8mol\%$ yttria-stabilized zirconia) cermet anode were $50.6\%\;and\;0.23{\mu}m$, respectively. The Ni particles in the anode were distributed uniformly and connected well to each other particles in the cermet anode. YSZ electrolyte layer and multilayered cathode composed of $LSM(La_{0.85}Sr_{0.15})_{0.9}MnO_3)/YSZ$ composite, LSM, and $LSCF(La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.7}O_3)$ were coated onto the anode substrate by slurry dip coating, subsequently. The anode-supported flat tubular cell showed a performance of $300mW/cm^2 (0.6V,\; 500 mA/cm^2)\;at\;500^{\circ}C$. The electrochemical characteristics of the flat tubular cell were examined by ac impedance method and the humidified fuel enhanced the cell performance. Areal specific resistance of the LSM-coated SUS430 by slurry dipping process as metallic interconnect was $148m{\Omega}cm^2\;at\;750^{\circ}C$ and then decreased to $148m{\Omega}cm^2$ after 450hr. On the other hand, the LSM-coated Fecralloy by slurry dipping process showed a high area specific resistance.

• Journal of Radiation Protection and Research
• /
• v.30 no.4
• /
• pp.185-196
• /
• 2005

Although medical exposure from diagnostic radiology procedures such as conventional x-rays, CT and PET scans is necessary for healthcare purposes, understanding its characteristics and size of the resulting radiation dose to patients is much of worth because medical radiation constitutes the largest artificial source of exposure and the medical exposure is in a trend of fast increasing particularly in the developed society. Annual collective doses and per-caput effective doses from different radiology procedures in Korea were estimated by combining the effective dose estimates per single medical procedure and the health insurance statistics in 2002. Values of the effective dose per single procedure were compiled from different sources including NRPB reports, ICRP 80, MIRDOSE3.1 code and independent computations of the authors. The annual collective dose reaches 27440 man-Sv (diagnostic radiology: 22880 man-Sv, nuclear medicine: 4560 man-Sv) which is reduced to the annual per-caput effective dose of 0.58 mSv by dividing by the national population of 47.7 millions. The collective dose is far larger than that of occupational exposures, in the country operated 16 nuclear power plants in 2002, which is no more than 70 man-Sv in the same year. It is particularly noted that the collective dose due to CT scans amounts 9960 man-Sv. These results implies that the national policy for radiation protection should pay much more attention to optimization of patient doses in medicine.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.43 no.4 s.310
• /
• pp.9-18
• /
• 2006

In the digital camera system, CMOS image sensor (CIS) is widely used because its size and weight become smaller and power consumption becomes lower. However, there are common problems that colors of the recorded image do not match those of the photographed object and that spectral sensitivity of the CIS used in different cameras varies largely in each case. Therefore, color correction is needed because the spectral sensitivity of the CIS in each color is neither the same color component for most standard colors nor the appropriate color representation for any output devices. In the conventional method, a color correction is empirically obtained by a large number of iterative experiments, but the result is not so satisfied. In this paper, a new method to obtain the efficient color correction matrix for digital camera using CIS is proposed. We obtain camera transfer matrix under the certain white-balance point, and color correction matrix that makes the transfer characteristic of digital camera close to the transfer characteristic of ideal camera is obtained. The experimental results show that the transfer characteristic of digital camera by the proposed method is close to that of the ideal camera. In addition, the image quality of pictures of digital camera using the proposed method is dramatically improved.

• Journal of Intelligence and Information Systems
• /
• v.12 no.2
• /
• pp.125-144
• /
• 2006

The development of mobile applications is fast in recent years. However, nearly all applications are for messaging, financial, locating services based on simple interactions with mobile users because of the limited screen size, narrow network bandwidth, and low computing power. Processing an algorithm for supporting a group decision process on mobile devices becomes impossible. In this paper, we introduce the mobile-oriented simple interactive procedure for support a group decision making process. The interactive procedure is developed for multiple objective linear programming problems to help the group select a compromising solution in the mobile Internet environment. Our procedure lessens the burden of group decision makers, which is one of necessary conditions of the mobile environment. Only the partial weak order preferences of variables and objectives from group decision makers are enough for searching the best compromising solution. The methodology is designed to avoid any assumption about the shape or existence of the decision makers' utility function. For the purpose of the experimental study of the procedure, we developed a group decision support system in the mobile Internet environment, MOBIGSS and applied to an allocation problem of investor assets.