• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.53 no.3
• /
• pp.152-160
• /
• 2004

A novel UPQC(Unified Power Quality Conditioner), which consists of series inverter, shunt inverter, distributed generation system, is proposed. The proposing system can compensate reactive power, harmonics, voltage sag and swell, voltage interruption etc. through the change of paralleling operation mode and islanding operation mode. The control strategy for the proposing system was derived using the instantaneous power method. The performance of proposing system was analyzed by means of the PSCAD/EMTDC simulation and the experimental work with the hardware prototype. The proposing system has the ultimate capability of improving power quality at the point of installation on power distribution systems or Industrial power systems and can be utilized for the custom power device in th future distribution system.

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.77-81
• /
• 2004

In this paper a novel line interactive UPS (Uninterruptible Power Supply) using the two 4-leg VSCs and AC line reactor is proposed. The 4-leg Voltage Source Converter(VSC) can use the DC link voltage effectively by the 3-D SVPWM method. Hence the DC battery voltage can be reduced by $15\%$ in comparison to that of the conventional line-interactive UPS system. One VSC is in parallel with the AC line reactor of the power source side, and the other is in series with the load. The parallel 4-leg voltage source inverter controls three-phase line voltage independently in order to control the line reactor current indirectly. It eliminates the neutral line current and the active ripple power of the source side using the pqr theory so that unity power factor and the sinusoidal source current can be achieved even though both the source and the load voltages have zero sequence components. The series 4-leg voltage source inverter compensates the line voltage and allows the load voltage to be balanced and harmonic-free. Both of parallel and series 4-leg voltage source inverters always act as independently controllable voltage sources, so that three-phase output voltage shows a seamless transition to the backup mode. The feasibility of the proposed UPS system has been investigated and verified through computer simulation results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.6
• /
• pp.626-633
• /
• 2005

This paper proposes a new 2MVA SSFG(Sag Swell Flicker Generator) injecting voltage by using series inverter. The proposed SSFG composes series inverter, DC capacitor as energy storage, rectifier and voltage clamp circuit. This SSFG is designed to generate typical power disturbances, such as voltage sag/swell, over/under voltage and voltage flicker. Also it is designed to generate unexpected voltage phase jumping waveform by controlling the series inverter. In this paper, three kinds of control methods for the proposed 2MVA SSFG we investigated by PSIM simulation. Also typical voltage sag, swell, flicker waveforms are implemented by adopting effective control method.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.6
• /
• pp.1037-1044
• /
• 2020

Since radar wind profiler (RWP) provides wind field data with high time and space resolution in all weather conditions, their verification of the accuracy and quality is essential. The simultaneous wind measurement from rawinsonde is commonly used to evaluate wind vectors from RWP. In this study, the simulation algorithm which produces the spectrum and raw time series (I/Q) data from the average values of moments is presented as a step-by-step verification method for the signal processing algorithm. The possibility of the simulation algorithm was also confirmed through comparison with the raw data of LAP-3000. The Doppler power spectrum was generated by assuming the density function of the skew-normal distribution and by using the moment values as the parameter. The simulated spectrum was generated through random numbers. In addition, the coherent averaged I/Q data was generated by random phase and inverse discrete Fourier transform, and raw I/Q data was generated through the Dirichlet distribution.

• Journal of Power Electronics
• /
• v.9 no.3
• /
• pp.396-402
• /
• 2009

A DC/DC converter generally needs to work under high switching frequency when used as an adjustable power supply to reduce the size of magnetic elements such as inductors, transformers and capacitors, but with the rising of the switch frequency, the switch losses will increase and the efficiency will reduce. Recently, to solve these problems, research is actively being done on a soft switching method that can be applied under high frequency and on a PWM converter that can be applied under low frequency such as a multi-level topology. In this paper a novel DC-DC conversion method for reducing the ripple of output voltage is proposed. In the proposed converter, buck converters are connected in series to generate the output voltage. By using this method, the ripple of output voltage can be reduced compared to a conventional buck converter. Particularly when output voltage is low, the number of acting switching elements is less and the result of ripple reduction is more obvious. It is expected that the converter proposed in this paper could be very useful in the case of wide-range output voltage.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.12 no.5
• /
• pp.12-18
• /
• 1975

Triac phase controlled pre-regulator를 이용한 직류안정화전원에서 제어소자 전력소모를 촤소로 줄이기 위하여, 부하전류의 증가에 따라 제어소자 양단전압을 낮추어 주는 회로를 고안하여 부가하였다. 이렇게 하므로써 제어소자의 전력소모가 약 40%정도 감소되어 방열장치가 간단해지거나 전력용량을 증가할 수 있게 되었으며 열발산이 곤란한 monolithic I.C.화에 유용하도록 하였다. A method on minimizing the power dissipation in the control element of a series D.C. voltage regutator is devised. An additional control circuit which reduces the average voltage drop across the control element according to increasing the load current is attached :o the trial phase controlled pre-regulator system. It is verified that the power dissipation in the control element is reduced up to 40% by this. circuit arrangement. The heat sink system can be simplified and the capacity of tile handling power is also increased. It is expected that this circuit arrangement can be applied to I.C. fabrication.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.1
• /
• pp.48-55
• /
• 2022

This paper proposes a battery remaining useful life (RUL) prediction method using a deep learning-based EMD-CNN-LSTM hybrid method. The proposed method pre-processes capacity data by applying empirical mode decomposition (EMD) and predicts the remaining useful life using CNN-LSTM. CNN-LSTM is a hybrid method that combines convolution neural network (CNN), which analyzes spatial features, and long short term memory (LSTM), which is a deep learning technique that processes time series data analysis. The performance of the proposed remaining useful life prediction method is verified using the battery aging experiment data provided by the NASA Ames Prognostics Center of Excellence and shows higher accuracy than does the conventional method.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.401-406
• /
• 2004

In this paper, a new time-domain adaptive predistortion scheme is proposed to compensate for the nonlinearity of high power amplifiers (HPA) in OFDM systems. A complex Wiener-Hammerstein model (WHM) is adopted to describe the input-output relationship of unknown HPA with linear dynamics, and a power series model with memory (PSMWM) is used to approximate the HPA expressed by WHM. By using the PSMWM, the compensation input to HPA is calculated in a real-time manner so that the linearization from the predistorter input to the HPA output can be attained even if the nonlinear input-output relation of HPA is uncertain and changeable. In numerical example, the effectiveness of the proposed method is confirmed and compared with the identification method based on PSMWM.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.9
• /
• pp.1577-1583
• /
• 2007

The development of a magnet for very high magnetic field is usually envisioned with the use of an HTS insert coil. Pancake windings have been commonly used for the insert coil. All pancake windings have been connected in series and excited by a single power source. In that case, it is inevitable to operate some of the pancake windings well below their critical current densities. To increase the central magnetic field of the magnet, this paper proposed a new excitation method of the pancake windings by exciting the pancakes windings independently using multiple power sources. Results of the calculation show proposed method increases the central magnetic field of the magnet which consisted of 8 pancake windings by 17% comparing with excitation by using a single power source.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.341-348
• /
• 2003

Photovoltaic systems normally use a maximum power point tracking (MPPT) technique ta continuously deliver the highest possible power to the load when variations in the insolation and temperature occur. A simple method of tracking the maximum power points (MPPs) and forcing the boost converter system to operate close to these points is presented through deriving small-signal model and transfer function of boost converter. This paper aims at modeling boost converter including equivalent series resistance of input reservoir capacitor by state-space-averaging method and PWM switch model with properly designed controller for maximum photovoltaic power tracking control.