• 한국산학기술학회논문지
• /
• 제12권5호
• /
• pp.2279-2284
• /
• 2011

기존의 수지상 배전계통은 사고 등에 대한 설비보호 및 전력공급 신뢰도 향상을 위하여 과전류보호협조방식을 채택하고 있다. 국내 배전계통의 경우, 그 보호방식 협조체계는 배전용변전소 동일 변압기 동일 모선에서 다수의 배전선이 각각 CB(변전소 차단기)를 통하여 인출되어 각 배전선로 이하에서 사고발생시 고장전류를 검출하여 해당 CB를 차단하도록 되어있다. 그러나, 이와 같은 보호방식을 채용하고 있는 배전계통에 분산전원이 도입될 경우 변전소 인출차단기의 차단용량은 영향을 받게 되므로 충분한 검토가 필요하다. 본 논문에서는 분산전원 도입시, 국내 배전용 변전소의 인출차단기에 대한 차단용량을 초과하지 않는 보호협조방법을 제시하고, 이를 PSCAD-EMTDC 계통해석 S/W Tool에 의하여 모의하여 검증하였다.

• 대한전기학회논문지:전력기술부문A
• /
• 제53권12호
• /
• pp.670-677
• /
• 2004

The Conventional approach for estimating the locations of transmission line shunt faults has been to measure the apparent impedance to the fault from a line terminal and to convert the reactive component of the impedance to line length. But, these methods do not adequately address the problems associated with the fault location on distribution systems. This thesis presents a technique that estimates the location of shunt fault on a radial distribution system that has several single and multiphase laterals. Tapped loads and non-homogenity of the distribution system are take into account. The developed technique, which can handle shunt faults was tested to evaluate its suitability. Results from computer simulation of faults on a model of a 25KV distribution lines like real system are presented. The results approved that the proposed technique works well for estimating the locations of the distribution line shunt faults.

• Journal of Electrical Engineering and Technology
• /
• 제1권2호
• /
• pp.137-144
• /
• 2006

This paper proposes novel protection schemes for grid-connected distributed generation (DG) units using the fault location algorithm. The grid-connected DG would be influenced by abnormal distribution line conditions. Identification of the fault location for the distribution lines at the relaying point of DG helps solve the problems of the protection relays for DG. The proposed scheme first identifies fault locations using currents and voltages measured at DG and source impedance of distribution networks. Then the actual faulted feeder is identified, applying time-current characteristic curves (TCC) of overcurrent relay (OCR). The method considering the fault location and TCC of OCR might improve the performance of the conventional relays for DG. Test results show that the method prevents the superfluous operations of protection devices by discriminating the faulted feeder, whether it is a distribution line where DG is integrated or out of the line emanated from the substation to which the DGs are connected.

• KEPCO Journal on Electric Power and Energy
• /
• 제5권4호
• /
• pp.311-321
• /
• 2019

정부의 재생e 3020 이행계획 및 제 8차 전력수급 기본계획과 함께 국내 분산 전원 연계 사업이 활발하게 진행되고 있다. 특히 2016년 10월 시행된 1 MW이하의 분산 전원 접속 보장 제도의 시행 이후, 배전 계통의 분산 전원 연계 신청이 급증함에 따라 송배전 설비부족으로 분산 전원 접속 지연이 일어나는 문제와, 이로 인해 국내 분산 전원의 70 %가 연계되어 있는 배전 계통의 신증설 투자비가 증가하는 문제가 이슈로 부각되고 있다. 현재 배전 계통의 분산 전원 수용력(hosting capacity) 확보 방법은 물리적인 배전 설비 추가 확충 이외에는 대안이 없는 것이 현실인데, 이러한 방식은 아래와 같은 어려움이 따른다. 첫째, 분산 전원의 대다수를 차지하는 태양광은 일조량이 풍부하고 지가가 저렴한 야외, 산악지역에 보급되므로 배전선로 경과지 확보가 점점 어려워지고 있다. 이로 인해 지중 구간이 증가하여 공사비가 증가하며, 태양광 야외 지역 위치로 공사 거리, 기간이 증가하게 된다. 둘째, 지자체의 공사 인허가 비협조 사례가 증가하여 이로 인해 공사가 지연되어 민원이 야기된다. 셋째, 배전선로 공사 자체에 1년 이상의 공사기간이 소요되므로 분산 전원을 적기에 접속시킬 수가 없으며, 넷째, 접속 신청은 지속 증가하므로 이에 따라 배전 설비 확충 비용 또한 지속 증가 할 수 밖에 없다. 이렇게 물리적 설비확충으로 발생하는 문제에 대응하여 접속 대기를 최소화하면서도 공사(투자비)를 최소화 할 수 있는 방안은 설비이용률을 극대화하는 것이며, 본 연구는 이러한 고민에서 시작되었다. 그러므로 본 논문에서는 현재 배전 계통의 분산 전원 연계 현황, 태양광 최대 출력 실적, 최소 부하, 선로 특성의 분석을 통해 배전선로의 분산 전원 상시연계용량 기준을 상향하기 위한 타당성을 검토하였으며, 배전선로의 분산 전원 상시연계용량 기준을 위한 상향(안)을 제시하였다.

• Wind and Structures
• /
• 제27권5호
• /
• pp.325-336
• /
• 2018

The physical infrastructure of the power systems, including the high-voltage transmission towers and lines as well as the poles and wires for power distribution at a lower voltage level, is critical for the resilience of the community since the failures or nonfunctioning of these structures could introduce large area power outages under the extreme weather events. In the current engineering practices, single circuit lattice steel towers linked by transmission lines are widely used to form power transmission systems. After years of service and continues interactions with natural and built environment, progressive damages accumulate at various structural details and could gradually change the structural performance. This study is to evaluate the typical existing transmission tower-line system subjected to synoptic winds (atmospheric boundary layer winds). Effects from the possible corrosion penetration on the structural members of the transmission towers and the aerodynamic damping force on the conductors are evaluated. However, corrosion in connections is not included. Meanwhile, corrosion on the structural members is assumed to be evenly distributed. Wind loads are calculated based on the codes used for synoptic winds and the wind tunnel experiments were carried out to obtain the drag coefficients for different panels of the transmission towers as well as for the transmission lines. Sensitivity analysis is carried out based upon the incremental dynamic analysis (IDA) to evaluate the structural capacity of the transmission tower-line system for different corrosion and loading conditions. Meanwhile, extreme value analysis is also performed to further estimate the short-term extreme response of the transmission tower-line system.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제51권12호
• /
• pp.704-713
• /
• 2002

This paper describes operational characteristics of wind turbine induction generators interconnected with distribution networks using PSCAD/EMTDC. Due to the simple and durable structure, induction generators are the most common type used in wind Power generation. Generally, induction generators are classified into two groups according to the shape of rotor, one is squirrel-cage type and the other is wound-rotor type. In this study, we simulate the start-up and the output variation of generators interconnected with distribution networks and compare the operational characteristics of squirrel -cage type and wound-rotor type induction generators located in the unfaulted distribution lines about the disturbance occurred on the associated distribution feeders emanated from the substation to which wind turbine generator is connected. In order to obtain the realistic results, we use the radial distribution network of IEEE 13-bus model.

• 조명전기설비학회논문지
• /
• 제24권10호
• /
• pp.85-89
• /
• 2010

During a ground fault the maximum fault current and neutral to ground voltage will appear at the pole nearest to the fault. Distribution lines are consisted of three phase conductors, an overhead ground wire and a multi-grounded neutral line. In this paper phase to neutral faults were staged at the specified concrete pole along the distribution line and measured the ground fault current distribution in the ground fault current, three poles nearest to the fault point, overhead ground wire and neutral line. A effect by grounding resistance of poles of ground fault current in the 22.9[kV] multi-ground distribution system. by field tests.

• 전기학회논문지
• /
• 제63권6호
• /
• pp.738-745
• /
• 2014

Recently, various measures have been discussed for overcoming depletion of fossil fuels and environmental pollution. One of the measures is electric vehicles. But electric vehicles has some limitations from high cost of battery and low efficiency, so operation distance of electric cars is limited. Also there are difficulties that charging lines should be connected by an electric car whenever it charges. Thus, many studies have been conducted to overcome the limitation using conventional batteries of electric vehicles. As a result, the OLEV(On-Line Electric Vehicle) was developed. But the OLEV system is some limitations. The OLEV system causes power quality problems when it charges. Power quality problem cannot be ignored because OLEV systems are closely connected by distribution grids. In this paper, the OLEV system is designed by using PSCAD/EMTDC, and the power quality is measured and evaluated. Power quality is divided by two cases; harmonics and high-frequency. Harmonics were evaluated according to IEEE Std. 519-1992. But the evaluation of High-frequency could not take it because there was no standard. For this reason, the data measured by OLEV system was compared with the EN50065 regulation.

• 소음진동
• /
• 제7권2호
• /
• pp.319-329
• /
• 1997

Wigner-Ville distribution has been recognized as a useful tool and applied to various types of mechanical noise and vibration signals, but its limitation which mainly comes from the cross-talk has not been well addressed. The cross-talk takes place for a signal with multiple components, simply because the Wigner-Ville distribution is a bilinear transform. The cross-talk often causes a negative value in the distribution. This cannot be accepted for the Wigner- Ville distribution, because it is an expression of power. Smoothing the Wigner-Ville distribution by convoluting it wih a window, is most commonly used to reduce the cross-talk. There can be infinite number of distributions depending on the windows. In this paper, we attempted to develop a distribution which is the best or the optimal in reducing the cross-talk. This could be possible by employing the ambiguity function. For a general signal, however it is difficult to express the ambiguity function as a mathematically closed form. This requires an appropriate modeling to make such expression possible. We approximated the Wigner-Ville distribution as a sum of linear segments. In the ambiguity function domain, the legitimate components are reflected as linear lines passing through the origin. Every lines has its own length and slope. But, the cross-talk is widely distributed in the ambiguity function plane. Based on this realization, we proposed a two-dimensional window which is in fact 'rotating window', that can eliminate cross-talk component. The rotating window is examined numerically and is found to have a better performance in reducing the cross-talk than conventional windows, the Gaussian window.

• 조명전기설비학회논문지
• /
• 제16권1호
• /
• pp.76-84
• /
• 2002

송전선과 배전선의 고장에 의한 voltage sag는 산업 수용가와 전력회사에 당면한 가장 중요한 전력품질(power quality) 문제들 중 하나가 되었다. voltage sag는 일반적으로 진폭과 지속시간 특성으로 기술되지만 voltage sag 현상을 규명하여 그 대책을 찾는데는 위상변위 특성을 반드시 고려해야 한다. 이 논문에서는 3상지락, 단선지락, 및 선간단락 사고가 발생하였을 경우에, 고장임피던스의 변화에 의한 voltage sag를 symmetrical components 해석을 이용하여 특성해석을 하였다. 이 때, voltage sag와 이들이 진폭과 위상에 미치는 효과를 고찰하였다. 3상지락과 같은 평형 고장은 모든 상에서 전압과 전류가 동일한 값으로 변화되고 또한 영상성분들은 영이 되었다. 그렇지만, 단선지락과 선간단락 고장과 같은 불평형 고장으로 인한 voltage sag는 진폭과 위상이 각 상마다 다르게 변화되었다. 해석결과를 확인하기 위하여 전력회로 모델들을 토대로 시뮬레이션을 수행하고 그 결과들도 검토되었다.