• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2011년도 춘계학술대회
• /
• pp.687-691
• /
• 2011

본 논문에서는 아날로그 트리밍용으로 사용되는 $0.18{\mu}m$ generic 공정 기반의 EM(Electro-Migration)과 eFuse의 저항 변동을 고려한 8bit eFuse OTP (One-Time Programmable) 메모리를 설계하였다. eFuse OTP 메모리는 eFuse에 인가되는 program power를 증가시키기 위해 external program voltage를 사용하였으며, 프로그램되지 않은 cell에 흐르는 read current를 낮추기 위해 RWL (Read Word-Line) activation 이전에 BL을 VSS로 precharging하는 방식과 read NMOS transistor를 최적화 설계하였다. 그리고 프로그램된 eFuse 저항의 변동을 고려한 variable pull-up load를 갖는 sensing margin test 회로를 설계하였다. 한편 eFuse link의 length를 split하여 eFuse OTP의 프로그램 수율 (program yield)을 높였다.

• Journal of the Optical Society of Korea
• /
• 제18권4호
• /
• pp.382-387
• /
• 2014

An all-reflective, simple noncollinear second harmonic (SH) autocorrelator is described for monitoring the shot-to-shot behavior of ultrashort high-power laser pulses. Two mirrors are used for the dispersion-free splitting of a pulse into two halves. One of the mirrors is able to adjust the delay time and angle between two halves of the laser pulse in a nonlinear crystal. We present the possibility of real-time measurement of the pulse duration, peak intensity (or energy), and the pointing jitters of a laser pulse, by analyzing the spatial profile of the SH autocorrelation signal measured by a CCD camera. The measurement of the shot-to-shot variation of those parameters will be important for the detailed characterization of laser accelerated electrons or protons.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2000년도 High Temperature Superconductivity Vol.X
• /
• pp.65-65
• /
• 2000

Microwave response of intrinsic Josephson junctions in mesa structure formed on HgI2-intercalated Bi2Sr2CaCu2O8+x single crystals was studied in a wide range of microwave frequency. With irradiation of 73${\sim}$76 GHz microwave, the supercurrent branch becomes resistive above a certain onset microwave power. At low current bias, the current-voltage characteristics show linear behavior, while at high current bias, the resistive branch splits into multiple sub-branches. The voltage spacing between neighboring sub-branches increase with the microwave power and the total number of sub-branches is almost identical to the number of intrinsic Josephson junctions in the mesa. All the experimental results suggest that each sub-branch represents a specific mode of collective motion of Josephson vortices generated by the microwave irradiation. With irradiation of microwave of microwave of frequency lower than 20 GHz, on the other hand, no branch splitting was observed and the current-voltage characteristics exhibited complex behavior at hlgh blas currents. This result can be explained in terms of incoherent motion of Josephson vortices generated by non-uniform microwave irradiation.

• 한국광학회지
• /
• 제4권4호
• /
• pp.420-427
• /
• 1993

융착 접속 기술을 이용하여 다중모우드 광섬유와 단일 모우드 광섬유내에 유전체 박막 거울을 제작하였다. $45{\circ}$ 유전체 거울이 내장된 광섬유는 극소형이며, 광학적인 손실이 매우 작고(1.3 ${\mu}m$에서, 다중 모우드 광섬유의 경우 0.2dB, 단일 모우드 광섬유의 경우 0.5dB), 기계적 강도가 우수한 결합기로 사용될 수 있다. 반사율은 파장에 따라 변화하며, 편광에 매우 민감하였다. 백색광을 사용하여 유전체 거울로부터 반사되는 출력 파워를 원거리 스캔하며 측정하였을 때 출력 빔의 모양은 거의 원형 대칭으로써 최대 파워의 5%에서 측정된 종횡비는 1.09이었다. 다이오우드 레이저 광원을 사용하여 측정한 다중모우드 광섬유 결합기의 광분파율은 종래의 FBT(Fused Biconical Taper) 결합기보다 입력 광신호의 결합 조건에 따른 변화가 훨씬 적어서 사용하는 광통신 시스템의 모우드 잡음에 덜 민감하다. 광섬유 축에 수직하게 증착된 다층 유전체 거울들의 반사율 스펙트럼 특성을 측정하였으며, 행렬 해석법을 사용하여 실험 결과를 분석, 고찰하였다.

• 천문학회보
• /
• 제41권1호
• /
• pp.38.2-38.2
• /
• 2016

The mapping of dark matter clustering from real to redshift spaces introduces the anisotropic property to the measured density power spectrum in redshift space, known as the Redshift Space Distortion (hereafter RSD) effect. The mapping formula is intrinsically non-linear, which is complicated by the higher order polynomials due to the indefinite cross correlations between the density and velocity fields, and the Finger-of-God (hereafter FoG) effect due to the randomness of the peculiar velocity field. Furthermore, the rigorous test of this mapping formula is contaminated by the unknown non-linearity of the density and velocity fields, including their auto- and cross-correlations, for calculating which our theoretical calculation breaks down beyond some scales. Whilst the full higher order polynomials remains unknown, the other systematics can be controlled consistently within the same order truncation in the expansion of the mapping formula, as shown in this paper. The systematic due to the unknown non-linear density and velocity fields is removed by separately measuring all terms in the expansion using simulations. The uncertainty caused by the velocity randomness is controlled by splitting the FoG term into two pieces, 1) the non-local FoG term being independent of the separation vector between two different points, and 2) the local FoG term appearing as an indefinite polynomials which is expanded in the same order as all other perturbative polynomials. Using 100 realizations of simulations, we find that the best fitted non-local FoG function is Gaussian, with only one scale-independent free parameter, and that our new mapping formulation accurately reproduces the observed power spectrum in redshift space at the smallest scales by far, up to k ~ 0.3 h/Mpc, considering the resolution of future experiments.

• 한국산학기술학회논문지
• /
• 제12권2호
• /
• pp.1032-1037
• /
• 2011

본 연구에서는 전처리 공정을 거친 천연가스로부터 에탄 이상의 성분을 회수하기 위한 탈메탄탑에 대한 전산모사와 공정 최적화를 수행하였다. 전처리된 천연가스는 탈메탄탑 상부의 차가운 기상류와의 열교환 및 프로판 냉동 사이클이 포함된 예냉공정을 거친 후에 기상과 액상이 분리된다. 기상은 터보 팽창기를 거치면서 생산되는 동력을 residue gas의 압력을 높이기 위한 압축기에 전달한 후에 부분적으로 응축되어 탈메탄탑 상부로 주입된다. 액상류는 줄-톰슨 팽창 밸브를 거친 후 더욱 냉각되어 탈메탄탑의 중간부로 주입된다. 원료 대비 에탄의 회수율은 80% 이상으로 정하였으며, 탈메탄탑의 탑저에서 에탄에 대한 메탄의 몰비는 0.0119로 정하였다. 한편 프로판 냉동 사이클의 heat duty를 최소화시키기 위해서 원료를 분리하여 side reboiler와 열교환시킴으로써 냉열의 일부를 회수할 수 있었다.

• Geomechanics and Engineering
• /
• 제30권5호
• /
• pp.401-411
• /
• 2022

To obtain the dynamic mechanical properties, fracture modes, energy and brittleness characteristics of Furong Baijiao coal rock, the dynamic impact compression tests under 0, 4, 8 and 12 MPa confining pressure were carried out using the split Hopkinson pressure bar. The results show that failure mode of coal rock in uniaxial state is axial splitting failure, while it is mainly compression-shear failure with tensile failure in triaxial state. With strain rate and confining pressure increasing, compressive strength and peak strain increase, average fragmentation increases and fractal dimension decreases. Based on energy dissipation theory, the dissipated energy density of coal rock increases gradually with growing confining pressure, but it has little correlation with strain rate. Considering progressive destruction process of coal rock, damage variable was defined as the ratio of dissipated energy density to total absorbed energy density. The maximum damage rate was obtained by deriving damage variable to reflect its maximum failure severity, then a brittleness index BD was established based on the maximum damage rate. BD value declined gradually as confining pressure and strain rate increase, indicating the decrease of brittleness and destruction degree. When confining pressure rises to 12 MPa, brittleness index and average fragmentation gradually stabilize, which shows confining pressure growing cannot cause continuous damage. Finally, integrating dynamic deformation and destruction process of coal rock and according to its final failure characteristics under different confining pressures, BD value is used to classify the brittleness into four grades.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2010년도 춘계학술발표대회
• /
• pp.3.1-3.1
• /
• 2010

Water splitting reaction using photocatalysts is of great interest in the utilization of solar energy [1]. In the present work, visible light-responsive $TiO_2$ thin films (Vis-$TiO_2$) were prepared by a radio frequency magnetron sputtering (RF-MS) deposition method and applied for the separate evolution of $H_2$ and $O_2$ from water as well as the photofuel cell. Special attentions will be focused on the effect of HF treatment of Vis-$TiO_2$ thin films on their photocatalytic activities. Vis-$TiO_2$ thin films were prepared by an RF-MS method using a calcined $TiO_2$ plate and Ar as the sputtering gas. The Vis-$TiO_2$ thin films were then deposited on the Ti foil substrate with the substrate temperature at 873 K (Vis-$TiO_2$/Ti). Vis-$TiO_2$/Ti thin films were immersed in a 0.045 vol% HF solution at room temperature. The effect of HF treatments on the activity of Vis-$TiO_2$/Ti thin films for the photocatalytic water splitting reaction have been investigated. Vis-$TiO_2$/Ti thin films treated with HF solution (HF-Vis-$TiO_2$/Ti) exhibited remarkable enhancement in the photocatalytic activity for $H_2$ evolution from a methanol aqueous solution as well as in the photoelectrochemical performance under visible light irradiation as compared with the untreated Vis-$TiO_2$/Ti thin films. Moreover, Pt-loaded HF-Vis-$TiO_2$/Ti thin films act as efficient and stable photocatalysts for the separate evolution of $H_2$ and $O_2$ from water under visible light irradiation in the presence of chemical bias. Thus, HF treatment was found to be an effective way to improve the photocatalytic activity of Vis-$TiO_2$/Ti thin films. Furthermore, unique separate type photofuel cell was fabricated using a Vis-$TiO_2$ thin film as an electrode, which can generate electrical power under solar light irradiation by using various kinds of biomass derivatives as fuel. It was found that the introduction of an iodine ($I^-/{I_3}^-$) redox solution at the cathode side enables the development of a highly efficient photofuel cell which can utilize a cost-efficient carbon electrode as an alternative to the Pt cathode.

• Journal of Electrochemical Science and Technology
• /
• 제8권4호
• /
• pp.265-273
• /
• 2017

Solid-state alkaline water electrolysis is a promising method for producing hydrogen using renewable energy sources such as wind and solar power. Despite active investigations of component development for anion exchange membrane water electrolysis (AEMWE), understanding of the device performance remains insufficient for the commercialization of AEMWE. The study of assembled AEMWE devices is essential to validate the activity and stability of developed catalysts and electrolyte membranes, as well as the dependence of the performance on the device operating conditions. Herein, we review the development of catalysts and membranes reported by different AEMWE companies such as ACTA S.p.A. and Proton OnSite and device operating conditions that significantly affect the AEMWE performance. For example, $CuCoO_x$ and $LiCoO_2$ have been studied as oxygen evolution catalysts by Acta S.p.A and Proton OnSite, respectively. Anion exchange membranes based on polyethylene and polysulfone are also investigated for use as electrolyte membranes in AEMWE devices. In addition, operation factors, including temperature, electrolyte concentration and acidity, and solution feed methods, are reviewed in terms of their influence on the AEMWE performance. The reaction rate of water splitting generally increases with increase in operating temperature because of the facilitated kinetics and higher ion conductivity. The effect of solution feeding configuration on the AEMWE performance is explained, with a brief discussion on current AEMWE performance and device durability.

• 한국산학기술학회논문지
• /
• 제12권3호
• /
• pp.1473-1478
• /
• 2011

본 연구에서는 전처리 공정을 거친 천연가스로부터 에탄 이상의 성분을 회수하기 위한 탈메탄탑에 대한 전산모사와 공정 최적화를 수행하였다. 전처리된 천연가스는 탈메탄탑 상부의 차가운 기상류와의 열교환 및 프로판 냉동 사이클이 포함된 예냉공정을 거친 후에 기상과 액상이 분리된다. 기상은 터보 팽창기를 거치면서 생산되는 동력을 residue gas의 압력을 높이기 위한 압축기에 전달한 후에 부분적으로 응축되어 탈메탄탑 상부로 주입된다. 액상류는 줄-톰슨 팽창 밸브를 거친 후 더욱 냉각되어 탈메탄탑의 중간부로 주입된다. 원료 대비 에탄의 회수율은 75% 이상으로 정하였으며, 탈메탄탑의 탑저에서 에탄에 대한 메탄의 몰비는 0.015로 정하였다. 한편 프로판 냉동 사이클의 heat duty를 최소화시키기 위해서 원료를 분리하여 side reboiler와 열교환시킴으로써 냉열의 일부 회수할 수 있었다.