• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.4 s.107
• /
• pp.351-357
• /
• 2006

In this paper, a direct $TM_{01}-TE_{11}$ mode converter of circular waveguide which is used the approximated design method of mode conversion between $TM_{01}$ and $TE_{11}$ modes is designed for radiation with the maximum directivity of high power energy into air (rom high power microwave antenna system. The proposed direct $TM_{01}-TE_{11}$ mode converter is calculated and designed with an approximated method for non-linear function about an extended non-constant serpentine type of circular waveguide. Then, the designed mode converter is optimized by length of 200 mm and efficiency above 95% by FIM simulation and achieved short length and high efficiency of the antenna by results of fabricated and measured characteristics.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.9
• /
• pp.559-564
• /
• 2016

This study examined the malfunction mode of the HCMOS IC under narrow-band high-power electromagnetic wave. Magnetron is used to a narrow-band electromagnetic source. MFR (malfunction failure rate) was measured to investigate the HCMOS IC. In addition, we measured the resistance between specific pins of ICs, which are exposed and not exposed to the electromagnetic wave, respectively. As a test result of measurement, malfunction mode is shown in three steps. Flicker mode causing a flicker in LED connected to output pin of IC is dominant in more than 7.96 kV/m electric field. Self-reset mode causing a voltage drop to the input and output of IC during electromagnetic wave radiation is dominant in more than 9.1 kV/m electric field. Power-reset mode making a IC remained malfunction after electromagnetic radiation is dominant in more than 20.89 kV/m. As a measurement result of pin-to-pin resistance of IC, the differences between IC exposed to electromagnetic wave and normal IC were minor. However, the five in two hundred IC show a relatively low resistance. This is considered to be the result of the breakdown of pn junction when latch-up in CMOS occurred. Based on the results, the susceptibility of HCMOS IC can be applied to a basic database to IC protection and impact analysis of narrow-band high-power electromagnetic waves.

• Journal of the Korean Society for Railway
• /
• v.18 no.6
• /
• pp.533-542
• /
• 2015

This paper suggest away to maintain constant power through trolley wire by transferring increased line voltage to the AC main line while changing the mode from Converter(Forward) to Inverter(Reverse) when the line voltage is increased due to regenerative power when the train stops, This paper suggests a Double Converter DC substation that can create regenerative power when the train stops reusable. We also proposed using a simulation tool, the optimal Thyrister firing angle that can minimize the undershoot and overshoot that occurs when transferring the mode from Converter to Inverter for quality improvement of DC voltage in the Double Converter in the DC substation from the Busan Urban Subway.

• Current Optics and Photonics
• /
• v.6 no.2
• /
• pp.143-150
• /
• 2022

Anti-resonant hollow-core photonic crystal fiber (AR-HCF) has unique advantages, such as low nonlinearity and high damage threshold, which make it a promising candidate for high-power laser delivery at distances of tens of meters. However, due to the special structure, optical properties such as mode-field profile and bending loss of hollow-core fibers are different from those of solid-core fibers. These differences have limited the widespread use of AR-HCF in practice. In this paper we conduct numerical analysis of AR-HCFs with different structural parameters, to analyze their influences on an AR-HCF's optical properties. The simulation results show that with a 23-㎛ air-core diameter, the fundamental mode profile of an AR-HCF can well match that of the widely used Nufern's 20/400 fiber, for nearly-single-mode power delivery applications. Moreover, with the ratio of cladding capillary diameter to air-core diameter ranging from 0.6 to 0.7, the AR-HCF shows excellent optical characteristics, including low bending sensitivity while maintaining single-mode transmission at the same time. We believe these results lay the foundation for the application of AR-HCFs in the power delivery of high power fiber laser systems.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.4
• /
• pp.363-368
• /
• 2003

In this paper, the characteristics of the horn antenna for the high power transfertation system is stuided and several kinds of a horn antenna are compared and finally a conical hem antenna using multi-mode is proposed. In the high power system, the efficiency of power transfer is very important. Therefore the feeding hem of a reflector must have a circular symmetric radiation pattern. And the side lobe must be suppressed to reduce a spillover power loss and interference. By using multi-mode in a circular hem antenna, the whole length can be shorter and the radiation pattern can be adjusted according to the shape and direction of a reflector. This is confirmed by the experiments.

• Journal of the Korean Society for Railway
• /
• v.14 no.5
• /
• pp.411-415
• /
• 2011

DC/DC switching power converters are commonly used to generate a regulated DC output voltages with high efficiencies from different DC input sources. The voltage mode DC/DC converter utilizes MOSFET (metal-oxide semiconductor field effect transistor), inductor, and a PWM (pulse-width modulation) controller with oscillator, amplifier, and comparator, etc. to efficiently transfer energy from the input to the output at periodic intervals. The fundamental boost converter and a buck converter containing a switched-mode power supply are studied. In this paper, the electrical characteristics of DC/DC power converters are simulated by program of SPICE, and the PWM controller is implemented to check the operation. In addition, power efficiency is analyzed based on the specification of each component.

• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.936-945
• /
• 2016

Large magnitude common-mode voltage (CMV) and its variation dv/dt have an adverse effect on motor drives that leads to early winding failure and bearing deterioration. For matrix converters, the switch states that connect each output line to a different input phase result in the lowest CMV among all of the valid switch states. To reduce the output CMV for matrix converters, this paper presents a new space vector modulation (SVM) strategy by utilizing these switch states. By this mean, the peak value and the root mean square of the CMV are dramatically decreased. In comparison with the conventional SVM methods this strategy has a similar computation overhead. Experiment results are shown to validate the effectiveness of the proposed modulation method.

• Journal of Power Electronics
• /
• v.19 no.2
• /
• pp.549-559
• /
• 2019

This paper proposes an adaptive sliding mode control (ASMC) strategy with an enhanced optimal reaching law (EORL) for the robust current tracking control of the boost converter based hybrid power source (HPS) in an electric vehicle (EV). A conventional ASMC strategy based on state observers and the hysteresis control method is used to realize the current tracking control for the boost converter based HPS. Then a novel enhanced exponential reaching law is proposed to improve the ASMC. Moreover, an enhanced exponential reaching law is optimized by particle swarm optimization. Finally, the adaptive control factor is redesigned based on the EORL. Simulations and experiments are established to validate the ASMC strategy with the EORL. Results show that the ASMC strategy with the EORL has an excellent current tracking control effect for the boost converter based HPS. When compared with the conventional ASMC strategy, the convergence time of the ASMC strategy with the EORL can be effectively improved. In EV applications, the ASMC strategy with the EORL can achieve robust current tracking control of the boost converter based HPS. It can guarantee the active and stable power distribution for boost converter based HPS.

• Proceedings of the IEEK Conference
• /
• 2001.06b
• /
• pp.45-48
• /
• 2001

An programmable current-mode folding and interpolation analog to digital converter (ADC) with programmable interpolator is proposed in this paper. A programmable interpolator is employed not only to vary the resolution of data converter, but also to decrease a power dissipation within the ADC. Because of varying the number of interpolation circuits, resolution is vary from 6 to 10bit. The designed ADC fabricated by a 0.6${\mu}{\textrm}{m}$ n-well CMOS double metal/single poly process. The experimental result shows the power dissipation from 26 to 87mW with a power supply of 3.3V.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.39-42
• /
• 1998

This paper is presented the Partial Resonant Soft Switching Mode Power Converter which is adapted the power converter having the partial resonant soft switching mode, that makes switches operated when the resonant current or voltage becomes zero by making the resonant circuit partially at turning on and off of the switches with suitable layout of the resonant elements and switch elements in the converter. Also, this paper includes the analysis and simulation of the Partial Resonant type Buck-Boost Chopper.