• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.980-981
• /
• 2015

A quasi-resonant flyback converter using a simple 8-bit microcontroller for a LED lighting is proposed in this paper. The proposed converter is easily and precisely controlled by the simple controller using a low-cost 8-bit microcontroller. Also, in order to operate the 8-bit microcontroller, the proposed converter system does not require any additional power supply for the controller. A prototype power supply is developed to supply a 270[W] LED lighting with the wide input voltage ranges ($175[V_{ac}]-265[V_{ac}]$). Experimental results will be show the practicality and validity of the proposed circuit.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.11
• /
• pp.1093-1100
• /
• 2016

This study is to demonstrate the superiority and stability of the solar - wind power hybrid power generation system for street lamps using super capacitor EDLC(:Electric Double Layer Capacitor). It is aiming to apply the lighting device using LED light source as the load of solar-wind power hybrid power generation system for independent power source and to develop the street light system device with high output power generation system. Unlike conventional controllers, EDLC, which is used as an auxiliary device for storing the developed power in the battery, can guarantee the high output and long life of the battery.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.1167-1171
• /
• 2008

The flow and thermal performance of the skiving and louver fin type heat sinks for the cooling system of the small LED projector were experimentally evaluated. A small fan tester based on AMCA standards was used to control and measure the air flow rate into the heat sink. Three heat blocks were used to simulate the heat and light sources(red, green and blue) of the small LED projector. We measured the pressure drop, temperatures and input power at the specific air flow rate and discussed those results. As a result, it is found that the louver fin type heat sink has higher pressure drop and lower thermal resistance than the skiving type. From the comparison of the temperature of the heat block between skiving and louver fin type, the louver fin type heat sink was found to be more suitable for cooling the high power heat source than skiving type. The thermal performance of the fan-sink(louver fin type) system was discussed with the picture taken by a thermal video.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.1
• /
• pp.233-239
• /
• 2015

The demand of remote control and monitoring for efficiency and applications of LED streetlight is increasing continuously because the demand of LED streetlight was increase last few years. Existing street light remote control system is wired using a power line network. The wireless connection exists, but due to its low data transmission rate, it cannot support specialized applications. It can only support simple control and monitoring. In this paper, we propose a system that uses a IEEE 802.11s wireless mesh network based on WLAN, as a backbone network for remote control and monitoring of the LED street lights along with other specialized applications. Using the wireless mesh network for remote control and monitoring the LED street lights, the same can be used to act like a public Wi-Fi access point. We have designed Wi-Fi integrated LED streetlight controller and implemented our system. We evaluated the performance of our system on a real test bed. Our proposed system is expected to perform the role of a U-city infrastructure by utilizing the wireless mesh network.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.53 no.3
• /
• pp.240-245
• /
• 2017

In order to study for the growth of fish in the aquaculture industry, the behavior analysis of rock bream (Oplegnathus fasciatus) depending on the temperature and LED lights was conducted. In this study, water temperatures from 10 to 30 degrees were used. One red light (wave length: 622 nm; light power: 811 mW) and one green light (wave length: 518 nm; light power: 648 mW) were used. Behavior of the rock bream was analyzed at an average moving distance for one minutes (AMD) and a rate of movement. The mean AMD were respectively 5.3 m, 7.3 m and 3.0 m in the red LED light, green LED light and control condition. The mean rates of movement were 77%, 88% and 61% respectively in the red LED light, green LED light and control condition. The mean AMD during 24 hours were 3.1 m, 3.1 m and 3.3 m respectively in the red LED light, green LED light and control condition.

• Journal of Industrial Technology
• /
• v.29 no.B
• /
• pp.133-137
• /
• 2009

This paper presents the development of smart road line lamp system consisting light control device. It can perform the individual power control or partial on/off control of a LED lamp by control center and can detect the error of the LEDs by current sensing. Also, the ability to control the brightness and period of on/off by detecting the car's existence. This light control circuit consists of road line lamp unit device. It can give a lot of solutions when the server, which controls the whole system, is operated through CDMA(Code-Division Multiple Access) network.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.11
• /
• pp.1931-1936
• /
• 2016

In this paper, we analyzed causes of accidents that recently increased in the illegal and defective LED lamps. They were analyzed by the electrical characteristics calculation and reappearance experiments. The causes of the accidents were analyzed from the circuit affected by the variation of voltage, current and power by harmonics. We drew a conclusion for electrical safety in illegal or degraded LED lamps from the analysis result. The management factors for electrical safety in LED lamps were harmonics, reactive power and power factor. It is possible to secure the electrical safety through monitoring of power factor in failure products and available in smart meters or smart distribution boards.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.5
• /
• pp.437-447
• /
• 2015

In this paper, implementation of an integrated transformer applicable to power supply units (PSUs) for a 150-W LED with a wide range of output voltage is presented. The transformer is comprised of a PFC inductor and an LLC resonant transformer, each of which is placed and integrated on an E-I-E-type magnetic core. Integrated transformers with two different air gap topologies (i.e., the side and center gap topologies) are considered in the design phase to investigate their applicability. The design consideration on the LLC resonant converter used for the wide-output-voltage control ranges is described, and the overall performance of the proposed system is verified through realization of it onto a 150-W LED PSU board.

• Journal of Sensor Science and Technology
• /
• v.31 no.1
• /
• pp.31-35
• /
• 2022

The efficacy improvement of the light emitting diode (LED) was studied for the realization of small-size, low power consumption, and highly sensitive bio-sensor instrument. The performance of the LED with Mg delta-doping at the interface of AlGaN/GaN super-lattice in p type cladding layer was simulated. The device with Mg delta-doping showed improved current, radiative recombination rate, electroluminescence, and light output power compared to the conventional LED structure. Under the bias condition of 5 V, the improved device exhibited 20.8% increase in the light output power. This is attributed to the increment of hole concentration from stable ionization of Mg in p type cladding layer. This result is expected to be used for the miniaturization, power saving, and sensitivity improvement of the bio-sensor system.

• Journal of IKEEE
• /
• v.21 no.4
• /
• pp.368-374
• /
• 2017

In this Paper, we developed a low power type LED security light using LED lighting that substitutes a 220[V] commercial power source for a solar cell module instead of a halogen or a sodium lamp. in addition, a PWM type drive control circuit is designed to minimize the heat generation problem and the drive current of the LED drive controller. in developed system, The light efficiency measurement value is 93.6[lm/W], and a high precision temperature sensor is used inside the controller to control the heat generation of the LED lamp. In order to eliminate the high heat generated from the LED lamp, it is designed to disperse quickly into the atmosphere through the metal insertion type heat sink. The heat control range of LED lighting was $50-55[^{\circ}C]$. The luminous flux and the lighting speed of the LED security lamp were 0.5[s], and the beam diffusion angle of the LED lamp was about $110[^{\circ}C]$ by the light distribution curve based on the height of 6[m].