• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.44 no.5
• /
• pp.84-93
• /
• 2007

In this paper, a Radix-8 structure for high-speed FFT is propose. Main block of the proposed FFT structure is Radix-8 DIF(Decimation In Frequency) butterfly. Even throughput of the Radix-8 FFT is twice than that of the Radix-4 FFT, implementation area of the Radix-8 is larger than that of Radix-4 FFT. But, implementation area of the proposed Radix-8 FFT was reduced by using DA(Distributed Arithmetic) for multiplication. For comparison, the 64-point FFT was implemented using conventional Radix-4 butterfly and proposed Radix-8 butterfly, respectively. The Verilog-HDL coding results for the proposed FFT structure show 49.2% cell area increment comparison with those of the conventional Radix-4 FFT structure. Namely, to speed up twice, 49.2% of area cost is required. In case of same throughput, power consumption of the proposed structure is reduced by 25.4%. Due to its efficient processing scheme, the proposed FFT structure can be used in large size of FFT like OFDM Modem.

• Steel and Composite Structures
• /
• v.24 no.4
• /
• pp.399-408
• /
• 2017

Of high strength bolts, the torque shear type bolt is known to be clamped normally when pin-tails are broken. Sometimes the clamping loads on slip critical connections considerably fluctuate from the required tension due to variation of torque coefficient. This is why the viscosity of lubricant affects the torque coefficient by temperature. In this study, the clamping tests of high strength bolts were performed independently at laboratory conditions and at outdoor environment. The temperatures of outdoor environment candidates were ranged from $-11^{\circ}C$ to $34^{\circ}C$ for six years. The temperature at laboratory condition was composed from $-10^{\circ}C$ to $50^{\circ}C$ at each $10^{\circ}C$ interval. At outdoor environment conditions, the clamping load of high strength bolt was varied from 159 to 210 kN and the torque value was varied from 405 to 556 Nm. The torque coefficients at outdoor environment were calculated from 0.126 to 0.158 when tensions were measured from 179 to 192 kN by using tension meter. The torque coefficients at outdoor environment conditions were analyzed as the range from 0.118 to 0.152. From these tests, the diverse equations of torque coefficient, tension dependent to temperature can be acquired by statistic regressive analysis. The variable of torque coefficient at laboratory conditions is 0.13% per each $1^{\circ}C$ when it reaches 2.73% per each $1^{\circ}C$ at outdoor environment conditions. When the results at laboratory conditions and at outdoor environment were combined to get the revised equations, the change in torque coefficient was modified as 0.2% per each $1^{\circ}C$ and the increment of tension was adjusted as 1.89 % per each $1^{\circ}C$.

• Ceramist
• /
• v.23 no.2
• /
• pp.184-199
• /
• 2020

The solid oxide fuel cells (SOFCs) are the one of the most promising energy conversion devices which can directly convert chemical energy into electric power with high efficiency and low emission. The lowering operating temperature below 800 ℃ has been considered as the mostly considerable research and development for commercialization. The major issue is to maintain reasonably high performance of SOFCs at reduced temperatures due to increment of polarization resistance of electrodes and electrolyte. Thus, the alternative materials with high catalytic activities and fast oxygen ion conductivity are required. For recent advances in electrolyte materials and technology, newly designed, highly conductive electrolyte materials and structural engineering of them provide a new path for further reduction in ohmic polarization resistance from electrolytes. Here, a powerful strategy of the bilayer concept with various oxide electrolytes of SOFCs are briefly reviewed. These recent developments also highlight the need for electrolytes with greater conductivity to achieve a high performance, thus providing a useful guidance for the rational design of cell structures for SOFCs. Moreover, cell design, materials compatibility, processing methods, are discussed, along with their role in determining cell performance. Results from state-of-the-art SOFCs are presented, and future prospects are discussed.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.6
• /
• pp.34-43
• /
• 2008

The state-space average model is extended to buck-boost, and buck-boost topology switching mode DC/DC converters and modified to have higher precision without increment of computation. The modified model is used in continuous conduction mode(CCM) switching DC/DC converters and some significant conclusions are derived. This paper discusses the discontinuous conduction mode(DCM) modeling of DC/DC converter and critical characteristic using average model of switch. Average model of switch approach is expended to the modeling of boundary conduction mode DC/DC converters that operate at the boundary between continuous conduction mode(CCM) and discontinuous conduction mode(DCM). Frequency responses predicted by the average model of switch are verified by simulation and experiment. A prototype featuring 15[V] input voltage, 24[V] output voltage, and 24[W] output power using MOSFET.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.4
• /
• pp.1123-1132
• /
• 1996

It has been reported that high temperature structural components represent the phenomenon of material degradation according to a long term service under high temperature and pressure. Especially, fossile power plant components using the fossil fuel and heavy oil are affected by dewpoint corrosion of $H_2SO_4$produced during a combustion. Therefore, the service materials subjected to high temperature and pressure may occur the stress corrosion cracking. The object of this paper is to investigate SCC susceptibility according to the material degradation of the high temperature structural materials in dewpoint corrosive environment-$H_2SO_4$.The obtained results are summarized as follows : 1) In case of secondary superheater tube, the fractograph of dimple is observed at the concentration of $H_2SO_4$-5%. When the concentration of $H_2SO_4$ is above 10%, the fracture mode is shifted from a transgranular fracture to an quasi-intergranular fracture according to the increment of concentration. 2) In the relationship between [$\Delta$DBTT]$_sp$ and SCC susceptibility, it is confirmed that the greater material degradation degree is, the higher SCC susceptibility is. In addition, it can be known that SP test is useful test method to evaluate SCC susceptibility for high temperature structural components. 3) When [$\Delta$DBTT]$_sp$ is above 17$17^{\circ}C$ the SCC fracture behavior is definitely observed with SCC susceptibility of above 0.4.

• The Journal of the Korea Contents Association
• /
• v.15 no.10
• /
• pp.336-345
• /
• 2015

This study conducted the following experiment to examine change of biophysical and physical fitness function on combined exercise program in 20' female university students with obesity according to heights of insole. Obesity related biophysical function was measured by basal metabolism and percent body fat(% Fat) and health related physical fitness was measured by isokinetic strength of quadriceps femoris muscle, muscular endurance, flexibility and power on comparative analysis of pre, post exercise and each groups(0cm, 5cm, 9cm) in 36 female university students with obesity subject according to heights of insole. These result lead us to the conclusion that each group were statistically improved at isokinetic muscular strength of quadriceps femoris muscle and basal metabolism, but 5cm group compared with 0cm and 9cm group was more significant improvement. Consequently, combination exercise applying appropriate heights of insole would be lead to positive increment of muscular strength and basal metabolism.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.17 no.4
• /
• pp.3943-3955
• /
• 1975

The purposes of this study are to evaluate the utilization characteristics of electrical power consumption, to grasp the present trends in the use of electrical equipments, to estimate the demand factor and load factor being held, and to evaluate the efficiency of electical uses for the recently electrified farms cultivating paddy rice. For the purposes, 109 sample farms located in eleven villiages electrified in six different years from 1968 to 1973, were chosen at random and investigated on 35 items concerning to electrical uses and wiring systems. The survey was carried out in 1975, in the vinicity of Suweon city. The results are summarized as follows: i) The average annual power consumption on sample farms is considered to be low, being 242.9 Kwh. in 1974, and varied according to the different electrified year and size of cultivated land, respectively. It has significant positive correlation to the area of farm, too. ii) Between the number of year of electrical uses and the power consumption, there is very significant positive correlation, which could be expressed as Y=43.041+16.108 X, where X represents the number of years of electrical uses. The annual increment of power consumption is much greater at the beginning of the electrification than that at the later years, its average being approximately 20 percent. However, it is recommended that any estimation of long-term increments should be carefully investigated. iii) The monthly power consumption varies considerably throughout a year, in which the heaviest farm load occurs in November. Observing the seasonal variation of consumption, the winter-time is the heaviest season while the summer is the lowest. The result implies house lighting is chief contribution to the present electrical consumption on the farms. Comparing the variation of monthly consumption ratios between the sample farms and industries, the electrical uses on the farms are independant of the industrial uses, and further, the agricultural uses are of inverse pattern to the farms from the results that there is negative correlationship between them, iv) The number of electrical equipments used on the farms are occupied chiefly by lighting sources. Next to the lighting sources, household appliances of small quantity and some motors are used. The mean electrical quantity is about 1, 127.4 watt, which corresponds to about 37.6 per cent to the contracted quantity. The composition of quantity is chiefly occupied by the electrical motor of about 1.5 hp., single-phased. The number of the annual utilization hours of each equipment is tabulated in Table IV-5. In contradiction to the high utilization of lighting sources and small household appliances, the motor is poorly used for approximately 22 hours in a year. v) More than 55 per cent of farms want to purchase new electrical equipments such as small household appliances and electrical motors in their number. The impulse of purchasing such items is stimulated by the contacts to the mass media and their knowledge on such equipments. Consequently, the increase of electrical uses could be prompted by such trials as education and demonstration. vi) The demand and load factors on the farms vary considerably according to the greater variation of the power consumption, daily or monthly. The daily demand factor is 22.4 per cent and load factor 18.6 per cent, while the annual demand factor is 1.3 per cent and load factor 70 per cent approximately. Therefore, the low efficiency of construction cost requires re-evaluation of the present contracted quantity of 3 Kw. or increase of electrical uses. vii) The electrical energy on the farms devoted chiefly to lighten the farm residences does not contribute to the farm incomes. Consequently, the cost of electrical consumption presses considerably upon the farm economy. Therefore, there is great need to build up the electrical uses on the farms through the development of new works and techinques to utilize any electrical equipments on the production of farm products. Further more, such the development should be related to increase the actual income of the farm consumers.

• Journal of the Korean Institute of Gas
• /
• v.23 no.6
• /
• pp.90-96
• /
• 2019

Natural gas has been regarded as one of major alternative fuels, because of the increment of mining shale gas and supplying PNG(Pipeline Natural Gas) from Russia. Thus, it needs to broaden the usage of natural gas as the increasing its supplement. In this situation, application of natural gas on the transport area is a good suggestion to reduce exhaust emissions such as CO₂(carbon dioxides) and soot from vehicles. For this reason, natural gas can be applied to SI(spark ignition) engines due to its anti-knocking and low auto-ignitibility characteristics. Recently, since turbocharged SI engine has been widely used, it needs to apply natural gas on the turbocharged SI engine. However, there is a major challenge for using natural gas on turbocharged SI engine, because it is hard to make natural gas direct injection in the cylinder, while gasoline is possible. As a result, there is a loss of fresh air when natural gas is injected by MPI (multi-point injection) method under the same intake pressure with gasoline-fueled condition. It brings the power reduction. Therefore, in this research, intake pressure was increased by controling the turbocharger system under natural gas-fueled condition to improve power output. The goal of improved power is the same level with that of gasoline-fueled condition under the maximum torque condition of each engine speed. As a result, the maximum power levels, which are the same with those of gasoline-fueled conditions, with improved brake thermal efficiency could be achieved for each engine speed (from 2,000 to 6,000 rpm) by increasing intake pressure 5-27 % compared to those of gasoline-fueled conditions.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.1 no.2
• /
• pp.120-126
• /
• 2006

In this paper, we propose for improving QoS in hospital wireless network using Cellular-IP/PRC(Paging Route Cache) with Paging Cache and Route Cache in Cellular-IP. Although the Cellular-IP/PRC technology is devised for mobile internet communication, it has its vulnerability in frequent handoff environment. This handoff state machine using differentiated handoff improves quality of services in Cellular-IP/PRC. Suggested algorithm shows better performance than existing technology in wireless mobile internet communication environment. When speech quality is secured considering increment of interference to receive in case of suppose that proposed acceptance method grooves base radio station capacity of transfer node is plenty, and most of contiguity cell transfer node was accepted at groove base radio station with a blow, groove base radio station new trench lake acceptance method based on transmission of a message electric power estimate of transfer node be. Do it so that may apply composing PC(Paging Cache) and RC(Routing Cache) that was used to manage paging and router in radio Internet network in integral management and all nodes as one PRC(Paging Router Cache), and add hand off state machine in transfer node so that can manage hand off of transfer node and Roaming state efficiently, and studies so that achieve connection function at node. Analyze benevolent person who influence on telephone traffic in system environment and forecasts each link currency rank and imbalance degree, forecast most close and important lake interception probability and lake falling off probability, GoS(Grade of Service), efficiency of cell capacity in QoS because applies algorithm proposing based on algorithm use gun send-receive electric power that judge by looking downward link whether currency book was limited and accepts or intercept lake and handles and displays QoS performance improvement.

• Journal of Korean Society of Environmental Engineers
• /
• v.39 no.4
• /
• pp.186-193
• /
• 2017

Microwave (MW) is an effective method for solubilizing organic solids because it has thermal, non-thermal and ionic conduction effects by dielectric heating and high energy efficiency. In this study, we evaluated the application of MW to the solubilization of cattle manure and investigated the solubilization ratio of cattle manure by solid concentration, MW power and target temperature. And $H_2SO_4$ and NaCl were added to investigated the effects on the MW-assisted solubilization. Also, we evaluated the solubilization efficiency by biochemical methane potential(BMP) test according to the solubilization conditions. Maximum SCOD increment per energy supply was 70.5 mg $SCOD_{increased}/kJ$ at 12% of the solid concentration, MW power of 800 W and the target temperature of $40^{\circ}C$. And SCOD concentration went up 153.2% compared to the initial concentration. In the MW-assisted solubilization with $H_2SO_4$ and NaCl as chemical catalysts, SCOD concentration was increased by 36% and 22.7%, respectively, compared to the result of MW. The methane production was increased by 13.3% and 11.3% with the addition of $H_2SO_4$ and NaCl. Therefore, MW is an effective method for solubilization of cattle manure, and it is necessary to use chemical catalysts to increase the solubilzation efficiency.