• KIPS Transactions on Computer and Communication Systems
• /
• v.2 no.3
• /
• pp.111-116
• /
• 2013

With technology scaling, soft error rate has greatly increased in embedded systems. Due to high performance and low power consumption, VLIW (Very Long Instruction Word) architectures have been widely used in embedded systems and thus many researches have been studied to improve the reliability of a system by duplicating instructions in VLIW architectures. However, existing studies have ignored the feature, called VLES (Variable Length Execution Set), which is adopted in most modern VLIW architectures to reduce code size. In this paper, we propose how to support instruction duplication in VLIW architecture with VLES. Our experimental results demonstrate that a VLIW architecture with VLES shows 64% code size decrement on average at the cost of about 4% additional cell area as compared to the case of a VLIW architecture without VLES when instruction duplication is applied to both architectures. Also, it is shown that the case with VLES does not cause extra execution time compared to the case without VLES.

• Nuclear Engineering and Technology
• /
• v.53 no.6
• /
• pp.1964-1969
• /
• 2021

We developed a Dual-PPACs detector for fast neutron measurements that consists of two sets of PPAC: conventional PPAC and fission PPAC. A²³⁸U(U₃O₈) coating is placed in the fission PPAC's anode, which is used as the neutrons conversion layer. An experiment was performed to measure neutron time-of-flight (TOF) in which ²⁵²Cf spontaneous fission source was used. An excellent time resolution of 164ps has been observed at 6 mbar in isobutene gas. With the excellent time resolution of Dual-PPACs detector, exact neutron energy can be extracted from the timing measurement. The experimental detection efficiency was 1.9 × 10^-7, consistent with the efficiency of 2.5 × 10^-7 given by a Geant4 simulation. Ultimately, the results show that the Dual-PPACs detector is a suitable candidate for measuring fast neutrons in the future CiADS system.

• Nuclear Engineering and Technology
• /
• v.51 no.5
• /
• pp.1417-1427
• /
• 2019

In this study, we evaluated the performance of a commercial pixelated cadmium zinc telluride (CZT) detector for spectroscopy and identified its feasibility as a Compton camera for radiation monitoring in a nuclear power plant. The detection system consisted of a $20mm{\times}20mm{\times}5mm$ CZT crystal with $8{\times}8$ pixelated anodes and a common cathode, in addition to an application specific integrated circuit. The performance of the various radioisotopes $^{57}Co$, $^{133}Ba$, $^{22}Na$, and $^{137}Cs$ was evaluated. In general, the amplitude of the induced signal in a CZT crystal depends on the interaction position and material non-uniformity. To minimize this dependency, a drift time correction was applied. The depth of each interaction was calculated by the drift time and the positional dependency of the signal amplitude was corrected based on the depth information. After the correction, the Compton regions of each spectrum were reduced, and energy resolutions of 122 keV, 356 keV, 511 keV, and 662 keV peaks were improved from 13.59%, 9.56%, 6.08%, and 5%-4.61%, 2.94%, 2.08%, and 2.2%, respectively. For the Compton imaging, simulations and experiments using one $^{137}Cs$ source with various angular positions and two $^{137}Cs$ sources were performed. Individual and multiple sources of $^{133}Ba$, $^{22}Na$, and $^{137}Cs$ were also measured. The images were successfully reconstructed by weighted list-mode maximum likelihood expectation maximization method. The angular resolutions and intrinsic efficiency of the $^{137}Cs$ experiments were approximately $7^{\circ}-9^{\circ}$ and $5{\times}10^{-4}-7{\times}10^{-4}$, respectively. The distortions of the source distribution were proportional to the offset angle.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.5
• /
• pp.349-357
• /
• 2022

Since the flight control computer of unmanned aerial vehicle (UAV) is a flight critical equipment, it is necessary to ensure reliability and safety from the development step, and a redundancy-based fault management design is required in order to operate normally even a failure occurs. To reduce cost, weight and power consumption, the dual-redundant flight control system design is considered in UAV. However, there are various restrictions on the fault management design. In this paper, we propose the fault detection and isolation designs for the dual-redundant flight control computer to satisfy the safety requirements of an UAV. In addition, the flight control computer developed by applying the fault management design performed functional tests in the integrated test environment, and after performing FMET in the HILS, its reliability was verified through flight tests.

• Journal of the Korean Institute of Gas
• /
• v.25 no.6
• /
• pp.1-6
• /
• 2021

In this study, we developed AMI terminals of 1 (reader): N (small transmitter). Currently, the government is focusing on the Gas AMI demonstration project to advance the outdated metering system of the urban gas industry, led by the government-sponsored ministries. The supply of gas AMI meters has the advantage of resolving uncertainties in privacy violations and measurement information and preparing for consumer safety through gas leakage detection. In the case of existing AMI meters, readers and transmitters were 1:1 methods, while this technology can be extended to multiple generations with a 1:N method, and a technology that can extend battery life by implementing a low-power design is applied. We hope that this research will contribute to the gas AMI supply project in the future.

• Journal of IKEEE
• /
• v.26 no.1
• /
• pp.36-42
• /
• 2022

This study presents an analysis of the human body channel as an electric signal path using body impulse response (BIR). The human body communications (HBC) has recently emerged as an effective signal transmission method to create wireless body area networks (WBAN). We provide body channel characteristics based on measured BIR in a proper experimental environment for the HBC using capacitive coupling with a customized channel sounding device, which can be applied as a guideline for the HBC system design. The frequency response of the BIR, extracted by a customized signal processing for the measure signals, shows the channel path loss (CPS) between 0 MHz and 100 MHz with an average CPS of approximately 46.8 dB. In addition, the relative noise power distributions can provide estimations on the signal to noise ratio at the HBC receiver in terms of capacitor and resistor values in the measured frequency band and the frequency band lower than 3 MHz considering the baseband signal detection.

• Journal of the Korean Institute of Gas
• /
• v.28 no.1
• /
• pp.53-58
• /
• 2024

Due to the development of industry and improvement of living standards, the amount of natural gas used in the world is constantly increasing, and related industrial facilities such as power plants, storage facilities, and supply pipelines are constantly increasing. Natural gas is a convenient and clean fuel that does not pollute the environment, but in the event of an accident due to leakage, it can cause human casualties, large-scale property damage, and negative effects on the global warming effect. In addition to the severe penalties under the Severe Disaster Punishment Act, it is necessary to ensure safety. Therefore, by applying the principle of laser-based absorption spectroscopy, we developed a long-range portable methane leakage gas detection system that can detect the concentration of methane leaking from a distance of up to 30 meters and verified its effectiveness.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.35 no.1
• /
• pp.61-67
• /
• 2015

Recently, the initiation of outside diameter stress corrosion cracking (ODSCC) at the tube support plate region of domestic steam generators (SG) with Alloy600 HTMA tubes has been increasing. As a result, SGs with Alloy600 HTMA tubes must be replaced early or are scheduled to be replaced prior to their designed lifetime. ODSCC is one of the biggest threats to the integrity of SG tubes. Therefore, the accurate evaluation of tube integrity to determine ODSCC is needed. Eddy current testing (ECT) is conducted periodically, and its results could be input as parameters for evaluating the integrity of SG tubes. The reliability of an ECT inspection system depends on the performance of the inspection technique and abilty of the analyst. The detection probability and ECT sizing error of degradation are considered to be the performance indices of a nondestructive evaluation (NDE) system. This paper introduces an optimized evaluation method for ECT, as well as the sizing error, including the analyst performance. This study was based on the results of a round robin program in which 10 inspection analysts from 5 different companies participated. The analysis of ECT sizing results was performed using a linear regression model relating the true defect size data to the measured ECT size data.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.12
• /
• pp.863-870
• /
• 2012

The market trends of automatic meter reading associated with smart water meters were investigated. Also, recent developments and field applications of key technology for automatic meter reading associated with smart water meters were analyzed. Smart water meters have been manufactured mostly in United States and Europe and have been expanded their business to Asia. Integrated water management system combining with the additional functions such as real-time consumption metering, cost notification, water conservation, leak detection, water quality monitoring, and flow control have been operated in automatic meter reading. Both water quality and quantity data measured from smart water meters and sensors were transferred to data concentration units through neighborhood area network, and then were transferred to integrated server through wide area network. The data transfer methods were determined by comprehensively considering urban scale, density of smart water meters, power supply and network topologies. Common data collection methods such as fixed network to data concentation units, vehicles drive by, people walk by, and drone fly by have been applied. The automatic meter reading associated with smart water meters are spread throughout the world, and both water and energy savings result in saving the money and reducing the greenhouse gases emission.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.1
• /
• pp.17-27
• /
• 2005

In this paper, we introduce a Parallel Interference Canceller (PIC) based sorting method to improve performance in the MC-DS/CDMA environment. A conventional PIC estimates and subtracts out all of the MAI (Multiple Access Interference) for each user in parallel. The parallel process ensures the low delay for the detection of all users. Also this scheme requires more stages for having better performance. Since the performance of PIC is strongly related to the correct MAI estimation, we introduce the IC (Interference Cancellation) scheme to estimate the accurate weaker signal group than the desired signal using conventional PIC. The principle of the proposed receiver sorts in descending order by the strength of signal and subtracts the MAI of the strong interferers from the desired signal for the accurate estimate of the weaker signals. Following this, the proposed scheme cancels out the improved weaker interference from the desired signal, using the output of the pre-step. In this result, the proposed system obtains better BER performance than the conventional PIC because the accuracy of the strong signal is improved. However, a disadvantage exists in that the processing time has slightly longer delay than the PIC owing to the power sorting and the MAI estimation process. The system performance evaluates and compares other non-liner It according to the number of sub-carriers in the limited-bandwidth.