• 한국컴퓨터정보학회논문지
• /
• 제23권8호
• /
• pp.51-57
• /
• 2018

In this paper, we investigate the impact of channel estimation error on the D2D power control algorithm. In the previous work, D2D power control algorithm has been proposed under the assumption that the channel between the transmitter and the corresponding receiver is perfectly estimated. In reality, the channel estimation error is more often the case. The first question is that the power control algorithm designed for perfect channel estimation is still valid under the channel estimation error environment ? The second question is, if it is not valid, what could be the possible remedy for the channel estimation error ? In this paper, to answer the first question, we investigate the impact of the channel estimation error on the power control algorithm. We first review the D2D power control algorithm designed for perfect channel estimation. Then, we model the channel estimation error. Finally, we summarize the main results observed from the analysis of the simulation.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 추계학술대회 논문집
• /
• pp.85-89
• /
• 2004

This paper presents Power Control and Distribution Unit development of GEO satellite with 3kW power output. The sensing error of bus voltage produce control signal of the shunt switch assembly and battery power converter, and the tolerance of error signals generated decide the stability of proposed system. The dynamic characteristics of main bus according to the load changing and the control logic of FPGA are simulated. In order to verify the proposed design, the simulation and experimental results for solar array shunt switch, battery power converter and bus controller are shown.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 D
• /
• pp.2669-2671
• /
• 2000

In this paper, a new model error following sliding mode control is considered with a novel sliding surface for the error. This novel sliding surface has nominal dynamics of an original state of the error system and makes it possible that the Sliding Mode Control(SMC) technique for the error of the model following is used with the various types of controllers. Its design is based on the augmented system whose dynamics have a higher order than that of the original error system. The reaching phase is removed by using an initial virtual state which makes the initial error state sliding function equal to zero.

• 전기학회논문지
• /
• 제67권10호
• /
• pp.1388-1394
• /
• 2018

In this paper, the improvement of the control response by using the error compensator to improve the stability of the control in the power conversion system is verified. Typically a closed loop control method is used to improve the control response characteristics in a traditional power conversion system and this is accomplished by generating a PWM waveform. In this paper, the newly constructed Type3 compensator to overcome the existing such as PI controller or Type2 compensator has been developed to improve the control stability of these closed loop control systems and the effectiveness of the use of error compensation devices was verified by presenting technique to improve stability and select its parameters by expanding the range of phase gains. Stability improvements are shown by the extension of the phase gain range and parameter selection techniques and the effects of using the error compensation device are verified accordingly.

• 동력기계공학회지
• /
• 제17권5호
• /
• pp.86-93
• /
• 2013

This paper proposes the used of genetic algorithm for optimizing PI controller and describes the dynamic modeling simulation for the permanent magnet synchronous motor driven by simplified vector control with the aid of MATLAB-Simulink environment. Furthermore, three kinds of error criterion minimization, integral absolute error, integral square error, and integral time absolute error, are used as objective function in the genetic algorithm. The modeling procedures and simulation results are described and presented in this paper. Computer simulation results indicate that the genetic algorithm was able to optimize the PI controller and gives good control performance of the system. Moreover, simplified vector control on permanent magnet synchronous motor does not need to regulate the direct axis component current. This makes simplified vector control of the permanent magnet synchronous motor very useful for some special applications that need simple control structure and low cost performance.

• Journal of Power Electronics
• /
• 제17권4호
• /
• pp.983-990
• /
• 2017

This paper proposes a model predictive control based on the discrete Lyapunov function to improve the performance of power electronic converters. The proposed control technique, based on the finite control set model predictive control (FCS-MPC), defines a cost function for the control law which is determined under the Lyapunov stability theorem with a control error compensation. The steady state and dynamic performance of the proposed control strategy has been tested under a single phase AC/DC voltage source rectifier (S-VSR). Experimental results demonstrate that the proposed control strategy not only offers global stability and good robustness but also leads to a high quality sinusoidal current with a reasonably low total harmonic distortion (THD) and a fast dynamic response under linear loads.

• 한국통신학회논문지
• /
• 제22권8호
• /
• pp.1632-1642
• /
• 1997

In this paper, we studied the effects of the power control imperfection on the system performances of a microcellular DS/CDMA system. The maximum user capacity, defined as the maximum number of users can be serviced simultaneouly, meeting a given voice quality, is first considered. Then the performence degradation due to the control error is analyzed. The frequency selective Raician channel model is used to characterize a microcellular mobile communication environment. The DS/CDMA system under consideration uses BPSK modulation and convolutional coding/Viterbe decoding with soft decision for forward error correction. It is shown that the user capacity falls linearly down with the increase of the power control error(in terms of the standard deviation in dB) and the interference from users outside the third tier cells have a minor effect on the performance. And the performance of DS/CDMA with the imperfect power control model is made to be less than 50% of that with perfect power control moded.

• 동력기계공학회지
• /
• 제22권1호
• /
• pp.18-24
• /
• 2018

This paper focuses on systematic design about the membership ranges of the main design factors such as control error, control error rate, and sampling time for the fuzzy logic control of the variable speed drive refrigeration cycle. The upper and the lowest limit of the membership ranges are set up from the data of static characteristics obtained by experiments. Three kinds of membership ranges on the control error and the control error rate are tested by experiments. Especially, an effect of sampling time on control performance is also investigated in the same way. Experimental data showed the control error rate and the sampling time strongly effected on the control performance of the refrigeration cycle with a variable speed drive.

• 한국정보기술응용학회:학술대회논문집
• /
• 한국정보기술응용학회 2005년도 6th 2005 International Conference on Computers, Communications and System
• /
• pp.335-338
• /
• 2005

In this paper, we propose a downlink power control scheme to apply in the unequal error protection multi-code CDMA mobile medicine system. The mobile medicine system contains (i) blood pressure and body temperature measurement value, (ii) ECG medical signals measured by the electrocardiogram device, (iii) mobile patient's history, (iv) G.729 audio signal, MPEG-4 CCD sensor video signal, and JPEG2000 medical image. By the help of the multi-code CDMA spread spectrum communication system with downlink power control scheme and unequal error protection strategy, it is possible to transmit mobile medicine media and meet the quality of service. Numerical analysis and simulation results show that the system is a well transmission platform in mobile medicine.

• 한국ITS학회 논문지
• /
• 제17권4호
• /
• pp.150-158
• /
• 2018

본 논문에서는 전력선 통신을 이용하는 전기자동차 충전 시스템에 대해 소개하고 전력선 통신을 이용하는 전기자동차 충전 시스템의 제어 신호에 오류가 발생했을 때 딥 러닝 알고리즘을 적용하여 오류를 정정하는 방식을 제안한다. 제어 신호의 오류 발견과 정정은 기존의 오류정정부호 기법을 통해 해결할 수 있으나 딥 러닝 기반의 오류정정부호 기법을 이용하여 더욱 효율적으로 오류를 발견하고 정정한다. 그래서 딥 러닝 기반의 오류정정부호 기법에 대해 소개하며 이 기법을 전력선 통신을 이용하는 전기자동차 충전 시스템에 적용하여 시뮬레이션을 진행하고 비트 오류율로 성능을 확인하여 딥 러닝 기반의 오류정정부호 기법이 기존의 기법보다 효율적인지를 판단한다.